1. On the vertical upright pipes i want to make the the ends at the top flat (60mm lenght) .Can this be done from within the frame generator.
Inventor 2012
I've got the basics down, made a couple of basic parts and a simple assembly but having a bit of an issue with constraining a part at 2 ends.
basically, i've got a simple wheel with a piston attached, think steam engine drive wheel. Ive produced a frame to attached it all too and can position the wheel to the frame and piston to the wheel and the cylinder to the piston but when i try to constrain the other end of the cylinder to the frame it all seems to go wrong and things start jumping all over the layout.
Is there a way for forcing a flat pattern, when unfolded, to a specific length?
View 6 Replies View RelatedAfter having a formed sheet metal part finish the wrong size (.100" long on all sides), I discovered a glitch with the sheet metal flat patterns sizes being.
I created two identical parts, one in IV2013 and one in IVP2014, and came up with two different flat patterns. The two parts are 100% identical. The volume is identical for both, and I did an assembly overlay to double check (everything lined up perfect). However, the flat pattern on the IV2014 part was 0.130" shy of what it should be (total length in both directions).
I haven't been able to recreate this (happened with this part and with a different part that we had formed), but you shouldn't ever have to worry about something like this. I created the same part in 2014 for a second time from scratch and it then came out to the correct dimensions, which worries me even more that this is an intermittent problem.
The JUNK file is the one with the incorrect length.
Also, another IVP2014 issue I have been having is when saving a drawing as an AutoCAD drawing it saves it as a 2013 AutoCAD in a zip file instead of a 2007 as a normal file like I have it set up to. If I click "Options" when saving, then click cancel without selecting anything, it saves it correctly.
I am trying to stylize my .shp file lines so that they have flat ends.
View 2 Replies View RelatedI'm wondering if there is a function in AutoCAD to 'press' (crush, flatten, pinch, crimp not sure the exact or correct term to be applied) the end of a steel tube? I've attached an image of a real piece of equipment where the tube is pressed at the end with a swivelling pin. Tube is 50mm outer diameter with a 3mm wall thickness.
View 9 Replies View RelatedI'm trying to write a VB.Net program (Visual Studio 2010 Express) for Inventor 2012 that will add up the length of all the edges of a flat pattern including any cutouts/holes in the part. I need the total length to do an estimate on the amount of time required to cut out the pattern on a laser. How to get this info programatically in VB?
i7-2720QM Dell Precision M6600, Win 7 Pro 64-bit, 8GB RAM
Autodesk Product Design Suite Ultimate 2013
Autodesk Vault Professional 2013
I want to have a Blank size custom iproperty using flat extents length and width this is what i did but gives error is there a way to get this to work the way I want it to? I dont want a Length and width to be seperated would like it all in one.
iProperties.Value("Custom", "BLANK SIZE")=Round(SheetMetal.FlatExtentsLength, 3)"X"=Round(SheetMetal.FlatExtentsWidth, 3)
How I have come to this question is through the process of trying to realistically show a hydrant in profile view. First off it it possible to create a completely vertical pipe in C3D? Also if you can, is it possible to show that in profile view? Basically, what I am trying to avoid is representing a fire hydrant pipe by creating some sort of custom cyclinder part in partbuilder. I have done this, but do not like the results.
Civil 3D 2013 SP2 | Win 7 64-bit SP1
Intel Core i5-2500 @ 3.30GHz, 8GB Ram | ATI Radeon HD 5450
Reducing the Roundness of a calligraphic brush to 0% seems to create 'flat' ends to a stroke, but, on closer inspection, the ends are not perfectly flat/straight.
The line seems to start and end with a slight 'S' curve; it's less visible when the stroke has a different bearing, but I need it to be gone - is this possible? I'm trying to create a calligraphic brush with perfectly flat ends.
how can i make each end of the spring flat.How best to cut the end sections so the wire is flat
Invenotr 2012
I want make Screw Shaft from sheet metal and make Flat pattern.
[URL]
How Can I Make Flat Pattern From A Part Of Cylinder ? (2013 Version)
Like Attached Image.
I noticed when you put in vertical parabolic curves onto the profile tangents it will ask you if you want length or k.
however depend on which one you specify. it will hold on to that value when it comes to changing the tangent locations. for what i am doing now i want k by default. but accidentally i put in length because i just went through all the pi's quickly to put in the curves. but i see no control which allows you to control which type to hold. this is a property inside the vertical curve but it's not exposed to user. once you create by length that's it. until you delete the curve and re enter using k then it will hold k.
How the length of the vertical curve is calculated in the C3D?
I’m wondering regarding the equation used to calculate the length of the vertical curve.
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
it is possible to make such a part from sheetmetal in order to create a flat pattern with Inventor 2010?
View 2 Replies View RelatedI have just made a new linetype but the ends look funny...I can't see why the ends, before and after the slash are different lengths? How to make them more even?
View 9 Replies View RelatedInventor 2013.
I want to make a contour roll and use the developed length option. How do I accomplish this.
The only way I can get this option to be available (not greyed out) is to have a closed loop sketch, if I have only a single line line sketch this option is not available.
I want to make a lintype where line starts with a point and ends with the point and in between is continuous line. Space from points to line should be 1 or 0.5 units depending on the scale I want to plot my drawing in.
View 7 Replies View Relatedtake a look to my Panorama, with attention to the sky. [URL]
It is made from this picture: [URL]
There is an error in the stitching because they are from different colors on the sides..
I can't find a way to create multi flat patters in one part from a lofted sheetmetal part. Also, didn't the developers fix the 'can't make a flat pattern from a derived part'?
IV 2010 Suite
Digital Storm PC:
EVGA & Intel components
Win 7 Pro 64 bit
I am looking to make a brush that I can use for cartooning in CS6 that starts out thin, gets thicker with pressure (I have a cintiq), and ends in a thin line.
View 22 Replies View RelatedI am using the design accelerator to create a shaft with multiple features. Works well. This shaft is 90"+ in length and although I realize we create in full scale, having it display into my drawing in full scale is unnecessary because one diameter is nearly 60" long. As such I would like to shorten it by using a shaft end, but cannot figure how to do it.
Just to be clear, by shaft end (term used in Mechanical) I refer to the squiggly lines that basically fudge the OAL of a component.
I recently bought Photoshop 12, having previously had Photoshop 9. With Photoshop 9 I could resize a photograph to 60mm by 40mm (say) and insert it into a text in Windows 7 at exactly that size and textwrap it. When I try to do this using Photoshop 12, the image fills the A4 page, even though it confirms that the resized photograph is 60mm by 40mm. What am I doing wrong?
View 1 Replies View RelatedWhen I open a drawing, Inventor 2012 update views. The default option is Background update". The problem is the update never ends... I can use Inventor, but the background update is ne finished, so I can't print a correct drawing.
If I disable Back upDate it is ok, but how can I use it ?
Basically a 2.5" id tube with a .06 wall thickness - 16ga exhaust tubing. Once I finaly got the drawing right, I cannot rip the part. The part has both ends cut. If one of the ends is left un cut I can create a sketch and put a point where I want to rip, and successully rip the part. If both ends has a cut end has a cut, there is a RIP error. How to overcome this headache? I am trying to make a template which If i can rip the part, I will be able to do so.
using autocad inventor
what I would like to know is the 'simple' way to create a keyway on a shaft in the middle that does not connect to the ends. End connecting keys are pretty basic to draw and extrude thru (maybe still a better way?)
File attached for viewing .
I am trying to export geometry found in a flat pattern sketch overlaid onto the flat pattern.
Since I am creating the output file manually I gather the flat pattern boundaries and bend center lines for output to a file.
When I add flat pattern sketch entities to the mix they do not overlay properly. What matrix would I have to push the sketch entities through to get them to the same coordinates as the flat pattern?
I have been trying to unfold round tubing made through the frame generator. Here are the steps I took:
1. Used Frame Generator
* both ends of the tube are notched
2. Opened part and converted into sheet metal
3. Used the following tutorial: URL...
4. Was not working so I drew sketches on both ends of the notched tubing and added points
5. Used rip tool (point to point) and did not work
* I made sure the thickness was the same
I thought I was doing something wrong so I generated a new round tubing frame with only 1 end notched and the other end flat and followed the tutorial. IT WORKED! I have came to the conclusion that you can not use the rip tool on tubing that has both ends notched.Is there a way where I can cut the tubing in half so I have 2 individual pieces/files of tubing with 1 end flat and 1 end notched?
I have a dxf file of a 3d model (cant attach as it exceeds the size limit) that I need to have put in a 2D dwg file. basically I need to flatten it to make a top and front view of the model.
I haven't work in 3d in some time and never worked with dxf files, so I'm not even sure this is possible. I tried opening the dxf in auto cad, but it doesn't seem to find the file..I cant see dxf extensions.
We work on animal designs for our jewelry. We would like to make lines going around the designs like a frame that would look like a rounded wire or pipe.
Handcrafted unique jewelry created in animal, wildlife, flower and western designs.