When I open a drawing, Inventor 2012 update views. The default option is Background update". The problem is the update never ends... I can use Inventor, but the background update is ne finished, so I can't print a correct drawing.
If I disable Back upDate it is ok, but how can I use it ?
Why is it that individual views in an .idw always need to be updated? I will highlight a view, the thunderbolt icon lights up, I choose to update it, the view in the browser turns red and then the view up dates. if I highlight the view again it tells me the view needs to be updated again.
View 6 Replies View RelatedI am using the design accelerator to create a shaft with multiple features. Works well. This shaft is 90"+ in length and although I realize we create in full scale, having it display into my drawing in full scale is unnecessary because one diameter is nearly 60" long. As such I would like to shorten it by using a shaft end, but cannot figure how to do it.
Just to be clear, by shaft end (term used in Mechanical) I refer to the squiggly lines that basically fudge the OAL of a component.
Basically a 2.5" id tube with a .06 wall thickness - 16ga exhaust tubing. Once I finaly got the drawing right, I cannot rip the part. The part has both ends cut. If one of the ends is left un cut I can create a sketch and put a point where I want to rip, and successully rip the part. If both ends has a cut end has a cut, there is a RIP error. How to overcome this headache? I am trying to make a template which If i can rip the part, I will be able to do so.
using autocad inventor
what I would like to know is the 'simple' way to create a keyway on a shaft in the middle that does not connect to the ends. End connecting keys are pretty basic to draw and extrude thru (maybe still a better way?)
File attached for viewing .
I've got the basics down, made a couple of basic parts and a simple assembly but having a bit of an issue with constraining a part at 2 ends.
basically, i've got a simple wheel with a piston attached, think steam engine drive wheel. Ive produced a frame to attached it all too and can position the wheel to the frame and piston to the wheel and the cylinder to the piston but when i try to constrain the other end of the cylinder to the frame it all seems to go wrong and things start jumping all over the layout.
I have been trying to unfold round tubing made through the frame generator. Here are the steps I took:
1. Used Frame Generator
* both ends of the tube are notched
2. Opened part and converted into sheet metal
3. Used the following tutorial: URL...
4. Was not working so I drew sketches on both ends of the notched tubing and added points
5. Used rip tool (point to point) and did not work
* I made sure the thickness was the same
I thought I was doing something wrong so I generated a new round tubing frame with only 1 end notched and the other end flat and followed the tutorial. IT WORKED! I have came to the conclusion that you can not use the rip tool on tubing that has both ends notched.Is there a way where I can cut the tubing in half so I have 2 individual pieces/files of tubing with 1 end flat and 1 end notched?
I made a change to my materials library. I changed the color (from dark grey to light grey) of one material. I then saved this back to my library.
Now, when I start a new part, I get a warning that the material does not match the library. So, rather than using the material in the part, I opened the template and updated the material to match the library. (Manage >Update Styles).
This is where the problems come into play. In the update styles dialog, if I compare materials against my custom materials and then compare it to my Favorites, it just a continuious circle. It is like the favorites are stored inside the part and do not get updated to match the custom materials library. (I thought the whole idea behind using a library was to get the information out of the parts).
Here is a short video showing what it does. [URL] .....
The only way I can get the favorites to match is to delete the favorite material, update the style and the add the favorite back in. That is a bunch of work. The problem I got with this is that there are thousands of parts that have been created that has this favorite in it. The only way to update these is to open each part (if I knew which one), delete the favorite, update the materials and then add the favorite back in.
I see the same thing in 2013 and 2014.
1. On the vertical upright pipes i want to make the the ends at the top flat (60mm lenght) .Can this be done from within the frame generator.
Inventor 2012
I am wondering if it is possible to do a style update (or style update check) upon open of a drawing?
The example would be that I have stuff made from way back that the colors/dimension sytles ect dont match the current standard and upon opening a file where they are not current, it would either prompt to update immediatly OR update automatically with no prompting (preferred method).
I am doing a massive amount of updates from old files recently and to save myself 1 - 3 clicks per drawing would be wonderful.
I am trying to create a second base view (using Layout/Create View/Base from model space). The problem is, I need it to be rotated from the original base view. However, when I rotate the part in model space, ALL of my views change.
So I guess my question is, how do I create multiple views of the same part that are seperate from the other base views?
i have views lets say 3 views on a sheet but in the list of views theres mores that appears maybe i inserted the extra views that are showing but i deleted them to put them on another sheet
the problem is they show up in the list of both sheet and i can't delete them from the list of the sheet that they were before
How could I get the idw views to name themselves? Instead of ” view 1”, “view2” why not have it name itself the file name, the same goes for a parts-list added to idw sheets? When slow clicking them to rename they already have the file name referencing the view or parts list. I have multiple views and multiple parts list on many sheets. Re-naming them is starting to get old!
I took a quick look at “ILOGIC” because that’s my “ILOGIC” speed and nothing jumped out at me.
Is there a way to change the way the dimensions text shows up at arbitrary angles and make them all uniform?
View 4 Replies View RelatedI have two seperate parts that I have laid out on a drawing. I wish to align these parts.... Is this possible?
View 2 Replies View RelatedIs there a way of dimensioning the distance between the views on a .idw?
I have a series of drawings to make, that consist of two view each. I need to make them as consistant as possible, as far as the distance from view to view, accross the drawings.
So I am trying to create section views that detail the correct assembly of two parts.
These parts are welded on top of each other so its important to have clear understanding of how they fit together.
So imagine a pipe bent in the shape of a circle, in the horizontal plane, then holes drilled into the top (vertically) and then another pipe fitting in the holes and being welded together. This is what is happening.
So I am trying to create a section view of one of the holes with the welding information.
When I go to create the section view, I draw a line that would pass through the center of the large horizontal circle (but doesnt) and the center of the hole I am trying to detail and through to the outside of the horizontal pipe.
Now with this line I should get a view of the assembly exactly perpendicular to the line from that point. This is what is called "Aligned" in Inventor and what I was taught as a "Section View". However, this is not the case at all. I get what is called a projected section view.
find a way to get an "Aligned" view of this without sectioning the entire assembly. I just want the small bit necessary to show the relevant information.
Let's say I have a flat pattern view of my part and the bended top view of the same part on the same drawing and I want both of the left side of each to be in line. (The right side shortends after the bends occur but the left side is not changed at all)
Work around:
1. Export to autocad and line them up with the osnaps, etc
I know how to sketch per view and project geometry but thats still on each view and when I try to line them up I am using my eye. Is there a better way to line both up even though their on different views?
oBaseView = osheet.DrawingViews.AddBaseView(otargetDoc, oPoint1, DrawingViewScale, kFrontViewOrientation, kHiddenLineDrawingViewStyle, "Default")oDraftView = osheet.DrawingViews.AddAssociativeDraftView(otargetDoc, oPoint1, DrawingViewScale)
I have one base view and one draft view created all at point1 with the same scale. It seems to me the base view's center is at point1. But not that of the draft view.
Just wondering how to overlay them to looks like one view with the same origin point. Or what coordinate I adjust, so I can draw on draft view, but looks like I was drawing on the base view?
Some additional lines are needed in drawing but can't get from projection of a model.
When creating Views in .ipn files, using View Reps from .iam files, you get "Options" window where you can check Associative box, or leave it unchecked. How do yo get back to this window once the view is created?
View 6 Replies View RelatedI have a problem with one of my Inventor DWGs.
It seems that whenever I save the associated model, there is a chance that it ruin the drawing by scattering views, dimensions and sketches randomly.
We recently started using Inventor DWG files (shifting away from IDW).
Part of the process for one of our programmers is to open a DWG file using AutoCAD Mechanical 2012, delete all unused dimensions and views, and use the remaining view to program his CNC machine. We are finding that this is not possible to do with the new format Inventor DWG files, as the views are not able to be selected.
What is the AutoCAD 2012 procedure for deleting views created with Inventor DWG?
I want to extract 2D drawing view of the attached model. I tried but could not succeed because most of the sketches are on the angled user defined work planes.
See the following links, I did the same for some of my other models:-
[URL] ...
[URL ...
How can I show the modelling process of this model with 2D drawings?
I create muliti solid parts. In the .idw view I want the section views to have same colour as the model. Is it possible?
View 6 Replies View RelatedI have a part given to me from a customer that has ALL custom planes turned on. This file is large and has many assemblies, part, sub assy's.... too much to go thru one at a time. Can I turn all 'plane views' off at once? Why? Because I find it messy... no other reason.
View 3 Replies View RelatedI have an IDW file that has a corresponding .IPT Everytime you import a .ipt onto a sheet, a text accompanies it. I want to write a macros to edit this text.
As an usual practise it gives "VIEW, DESCRIPTION and SCALE" .
Instead of VIEW , I want the code to pick something from the i-properties.
Eg. Instead of VIEW, it shopuld write the STOCK NUMBER from the iproperties of the part.
Is this possible ?
I am using Inventor 2013. For some reason I cannot dimension some of the model entities in the drawing views in an idw file. I can retrieve the model dimensions but it is usually easier to create the dimensions I need in each view. I can select the line, curve, etc. when dimensioning but nothing happens.
After I think about it. What I cannot dimension are lofts that I created with rails. These rails were made up of lines and curves, not polylines. How do I get the sketches for the rails I used for lofting to display in the drawing views so I can dimension those sketches.
How to edit the explode steps in an explode file? I have created an exploded view of an assembly, only I have edited the assembly by adding a whole bunch of fasteners etc. Now I want to go into the explode file and add the extra components to the related exploded steps - only there is no steps to add the new components too, each component is on its own. The functionality I am talking about is a sw thing and there is probably another process to do this, or a work around.
View 9 Replies View RelatedI made a drawing and later changed the part to an ipart.
The dimensions of the table part in the drawing are o.k. but the iproperties, the contents of the logo doesn't update and it has a strange number string.
There is the yellow lightning symbol and even though i press update all sheets nothing happens and also the lightning symbol remains
At times when dimensioning or creating views in 2D, items will disappear. These items are dimensions or even complete views. They return as soon as hit the scroll wheel on the mouse or my 3D connexion mouse.
View 9 Replies View RelatedHow to get orthographic views from a 3d model?
View 9 Replies View Related