Inventor 2013.
I want to make a contour roll and use the developed length option. How do I accomplish this.
The only way I can get this option to be available (not greyed out) is to have a closed loop sketch, if I have only a single line line sketch this option is not available.
I'm having no problems creating the contour roll, but it won't let me add flanges to the outside edges. I have attached a file that shows the measurements that I want. I need to be able to create a flat pattern. The material thickness is .1046" and 3" deep.
View 1 Replies View RelatedA rather simple sheetmetal part won't result in a flat pattern. Pls. see attached screendumps.
The problem starts with the contour roll. Surpressing this contour roll feature (and dependent featured flange) results in a OK flat pattern.
IV Pro 2012, Win 7-64 Ult.
I've been having some issues recently with Sheet Metal parts. I am attempting to make a part that looks like this:
The only way I have been able to do this so far is by doing a contour roll to get the rounded part and then add the flanges on as part of an assembly.
I have attempted to do it as one Sheet Metal piece but I continually run into the problem where I cannot refold the part once I have the flanges.
Here are the steps I have gone through:
1. Created a contour roll to the necessary angle to get my desired dimensions
2. Unfolded the roll
3. Created my hole pattern
4. Folded back the flanges
This is where I got stuck. I attempted to refold the part between the bends but it will not let me do this. If I have one flange, I am able to refold but not when I have 2.
Another problem I have encountered is when I get one flange done, the thickness of it is larger than the rest of the part.
Autodesk Inventor Professional 2011
Windows 7 for Mac
80GB HDD Partition
Intel Core 2 Duo @ 2.66 GHz
2.75 GB Usable RAM
Inventor is awesome, quick to learn but sometime i get really blocked..Makes 2 hours i am trying everything to recreate a sheet of paper (a4) bended like a cone that isn t perfectly round but with the bottom flat.
I have attached a photo of what i am trying to create.I have tried to make it with using a triangle isosceles as the bottom and curve a sheet of metal using the "contour roll" between the 2 isocele sides.
I am getting an error message (see attached) when trying to create a contour roll using sheet metal, I have tried editing the sketch to open loop however I cannot get the contour roll to preview on the part.
The part is a short length of square hollow section from which I am trying to apply the roll to, there seems to be a problem in projecting the geometry on the end of the part
Inventor 2013 SP2 64-bit edition
Product Design Suite Ultimate 2013
64-bit HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
Inventor 2013-I'm working on a sheet metal cover using contour roll and I find when I dimension the flat pattern that radii that should be the same are not. Can my approach is fundamentally flawed? I tried making this part out of one 220 degree contour roll and I found when dimensioning that the center points of the arcs are not symmetric as expected. I then used two contour rolls to create the part basing the second contour roll on the first contour roll sketches and I still have the same issues.
View 4 Replies View RelatedI want to put a cable tray going from a sliding door to a fixed piece of steelwork. When the door opens and closes, I want the cable tray to adjust to suit the sliding door. I'll upload the file that I have made. When i drag the sketch it all moves accordingly, but when I placed in the assembly and make it adaptive it does nothing, it will not constrain and it will only bring up the errors.
Inventor 2012
Windows 7 64-Bit SP1
Intel(R) Xeon(R) CPU X5570 @ 2.93GHz
NVIDIA Quadro FX 3800 (Avail. Graphics Memory 4067MB - Ded. 1024 MB)
12 GB RAM
I am trying to design a welded Iron tank whose caps are made of sections, then welded together. I made one section using Contour Roll on Sheet Metal, and worked fine, but when I made the Flat Pattern it mades a square.
View 3 Replies View RelatedIf i draw e.g. the letter "R" i immediatly know height and width of this object. But what i want to know now is the exact length of the contour. How do i do that in X4?
View 2 Replies View Related1. On the vertical upright pipes i want to make the the ends at the top flat (60mm lenght) .Can this be done from within the frame generator.
Inventor 2012
produce a developed elevation of an assembly in inventor?
It is not sheet metal - I can't ask for a flat pattern.
Would it make any difference if I had an arc, or divided it up into numerous straight segments?
I need developed elevations for both arc and pentagon/hexagonal assemblies.
Refer to arc assembly attached.
"Developed Elevation" is missing from the "Place Views" toolbar.
I've done a grading "applying to entire lenght" but after done that I realized that I needed to do some located contentions. Is it possible to edit the grade for not applying it to entire lenght?When I go to the modify tab, edit grading, it does not appears the option "apply to entire lenght?"
View 9 Replies View Relatedi design shades and need to know is there a way to show material rolling up and un-roll from a roll in Inventor.
View 2 Replies View RelatedI want to make contour lines in autocad 2010 map 3d, but dont know how to start and where .
I have xyz coordinates in. txt format , something like this: [URL] .....
I tryed to do with spline, but its pretty hard some times :/. I need something that i can import and let autocad draw the contours, if its possbile (import txt or another format if its possible) !??
I have to make a roll of tape in Inventor, but I'm not too familiar with/used to the program. It's the small invisible adhesive tape, like the kind you'd find in office. So far, I sketched and extruded the plastic part the tape gets wrapped around, which is basically just a small tube. I also have a rectangle that's really long for the actual tape part, and that's extruded but very thin. they're both made as standard.ipt files. I opened a standard.iam file to put them together using constraints, but I'm not exactly sure how. I have the edge of the rectangle on the outside of the circle, so I just have to wrap it around. I'm assuming I just bend the rectangle (tape) around the circle (plastic part), but I don't know how to do that.
View 1 Replies View RelatedI have two cooling rools( just two cylindrical drums) a sheet is been passed on this. Wonder how do i draw the flexible sheet, actually i have many cylindrical rolls placed at different locations - all i want is a thin sheet to be passed onto each of those drums. Just like belt and pulley, but here sheet and a drum. Its very difficult to calculate dimensions and constrain, instead am wondering how do i create a flexible sheet of fixed length and constrain it so that they rest on top of the drums.
View 1 Replies View RelatedI'm still new using autodesk inventor and still learning. I have trouble to cut the plate (Penahan Depan.ipt) follow the radius of the roll (Roll.ipt).
View 4 Replies View RelatedI would like to make a thesis about software civil 3d, the concept of how to make contour, if the result is close to the original surface these results affect the accuracy of the data because in indonesia does not yet exist that discuss this. How to make contour 3d civil concept?
View 1 Replies View RelatedI have this contour lines from dwg file (see attached) and I am trying to make a surface out of it. Initially i thought it is already a surface for C3D but i cant seem to follow tutorials. While browsing for solutions from the Internet, it seems it is not even a contour file that can be added in C3D. what is this file and how i can convert it into a surface in C3D?
View 5 Replies View RelatedI am trying to make my contour labels visible, indepently of the Visible status of the contours in the surface style of the original surface that I am working on. I have to do this due the final topo looks strange in the borders so I am displaying another contours -that do not have elevation- and make look the drawing better. The problem is that if I turn off the Visible property of the contours, the labels turn off even that they were created in a different layer and attached to a label style with its own layer property.
View 6 Replies View RelatedI have this sheet metal part in which i want to roll the wide section into a cylinder with a small split at the top.Cannot get it to roll.
View 2 Replies View RelatedThe wheels on the side need to roll inside the guide rail. I can let them roll in each part separately but not in the entire rail.
I already tried with transitional constrains but then inventor says that there are some problems.My project needs to become a sectional gate so there's going te be lots more than just 2 wheels in it..
The part i make is from solid model>The part needs to be in sheet metal.What steps do i use to make as sheet metal part and have option to flatten part.
View 1 Replies View RelatedThe contour lines themselves are in model space. The contour texts are in paper space. How do I make the line hide under the text?
View 4 Replies View RelatedI am trying to make a circular sign with text inside it that follows the contour of the circle. Half of the text will be on the top and half on the bottom.
View 6 Replies View RelatedHow do I make a custom brush shape follow the contour of a path made with the Pen tool?
View 2 Replies View RelatedI am using Building Design Suite 2012 and trying to open a file that was emailed to me, when I try to open it I get an error that says "This DWG file was saved by an application that was not developed or licensed by Autodesk. What do you want to do?" When I choose continue opening DWG file it will open the file but it seems as if things are everywhere and outside the limits of the title sheet. I would think that possibly this was the intent of the drawing and they control the items outside of the title block with clipping or layer control, but here is where the weird part comes in, when I saved the file to my computer and try opening it from there (as opposed to directly from the email) when I click on it and it gives me the preview before opening the preview looks correct like the drawing is supposed to be. I have tried opening the file in Architecture 2012 and in TrueView 2012 and get the same results.
View 2 Replies View RelatedI have this drawing that I just finished. There were a few dotted lines that were showing up correctly in model space. Then, when I switched over to paper space all of those lines were solid. I messed around with the option LTSCALE and set it to 0.01. This made the lines show up correctly in paper space, but now they are all messed up in model space. Is there an option to make it so they show up exactly the same in both model and paper space?
View 9 Replies View RelatedI made a sketch for a bracket and used sheetmetal/contour flanges tool to make solid.I had to use 2 contour flanges to get the shape as i could not get it to work with 1 contour flange.Is this not possible due to something wrong with my sketch?
Other question is have i used the Cut tool correctly for the cut out of the brackets?
Inventor 2012
I made this sheet metal part, selected the arc sketch and the perpendicular edge like in the picture, but the contour flange isn't created
View 7 Replies View Related