I accidentally found a pyramid shape and imported on top of my solid part shape.
Where can I found it, so I can import it again, but this time as the main solid part.
I am trying to design 3 parts that assemble into the shape of my business logo.
I'm following a "Simple Mass Creation" exercise in a Revit book, which says to create a cube, a sphere, and a pyramid. It doesn't say how, though, it just goes on to the next step of dividing the masses into floors. After much research and trial and error, I figured out the cube and sphere, but how the heck do you create a pyramid? At first I was thinking of a blend, from a square to a point, but that's not an option. Then I tried to use void shapes to remove parts of a cube...and I'm getting an error message because my voids are overlapping and there's no solid to cut. There MUST be a faster and less complicated way to create such a basic form.
View 5 Replies View RelatedI am creating three shapes out of a pyramid. I figure if I split the pyramid in half, I can create two, then mirror them and blend the two together to make the final design. I have figured out how to create a pyramid by extruding a cube with a taper.
My pyramid is 40mm x 40mm x 40mm. I need to cut it in half, diagonally, top to bottom.
When I have the pyramid in the workspace, I see nothing that I can select - that will allow me to create lines where I need to - to cut them out.
I'll add a logo in 3-d that I am trying to create. (also, I am using this project to familiarize myself with the software.)
Using Mathcad, I can create a file with x and y values defining a 2D shape from which I want to create a swept volume.
I want to import these values into Inventor to use as a definition of a sketched line and then use the revolve function to generate the shape.
Is there a way to unfold a coil shape to get the flat pattern? When I try to unfold the attached part I get an error message (see attached error_msg.jpg). We have been using AutoPOL to unfold these kind of shapes (which works fine). But since we have a very old version which we really need to upgrade, I was wondering if nowadays Inventor could handle coil unfolds.
If this will not work with the current IV2013 release, will this then be implemented in a future release? Are there any alternatives or should I just go for the AutoPOL upgrade?
IV2013 Pro SP1
When i try to use Import Survey Database 'Create New Survey Database' i receive the following error.
Running Windows 7 Pro 64-bits and its fully updated. Also installed all the servicepacks available for Civil 3D
creating a existing surface single Curb/Gutter spot elevation label using two existing surface elevation points and not cogo points. I am a surveyor, and I want to be able to just click on both points one at a time (top of curb/gutter) to place the elevation label.
View 3 Replies View RelatedI want to engrave the text 'TEST' all the way around this clonal object. When I use the emboss tool, selecting the option 'wrap to face,' it gives me an error message that the "face selected is not tangent to the profile plane."
I am using a work plane that is offset from the XY plane. I included a screen shot and the file that I am using (Inv. 2014)
i am trying to draw an aircraft and after drawing the windows, i got stuck. i am trying to revolve a shape around the shape of the window (oval) but it won't recognise that shape as an axis. i can't click it. is there a solution to this?
here is a screenshot for extra info!
Having problems creating a helical truss/ shape. Ive managed to get a simple spline spiral. Which I'm still not 100 percent happy with. But it will suffice for right now.Now one of my problems is extruding, and offsetting. I'm pretty ok at 3d modelling, but when it comes to complex shapes i fall flat on my face. Ive including a dwg that shows a plan view of the structure, as well as my 3d spine. the small circles are the truss cords. Its a 16" flat truss, ran parallel with another to create a spiral ribbon.
The plan view is from the designer, I've noticed but maybe its not true... their helix doesn't seem consistent. I know im leaving a lot of info out.
I'm trying to create a linetpye .The line needs to be continuous with a solid(not hollow) circles at distances.This would be the same as FENCELINE1:
*FENCELINE1,Fenceline circle ----0-----0----0-----0----0-----0--
A,.25,-.1,[CIRC1,ltypeshp.shx,x=-.1,s=.1 ],-.1,1
but with filled-in circles.for example circles should be hatched or colored.An image of desired linetype is attached.
Assume that I have an odd pyramid 3D-solid say with a polygon basis that lies on a "floor". The apex was higher than the ceiling, so I "sliced" the pyramid to fit it right under the ceiling.
Now, I change my mind and want to make the ceiling slightly higher (say, 1"): after raising the ceiling I am left with a sliced pyramid that is cut 1"below the ceiling. Question is : what is the best way to re-extend the pyramid (and make it look like it was cut by the higher ceiling) ?
I cannot just "undo" because too many things happened in the meantime.
I can imagine re-creating the unsliced pyramid by press-pulling the upper sliced surface and then slice this extension with each side of the original sliced pyramid and ultimately re-slice with the new ceiling. Can I do better / faster than that ?
I was given a job where i need to create a surface from a gis file. have been messing with my civ 3d 2013 a little bit and have been able to get a surface comprised of a bunch of polylines to appear (not a true surface). I will need to create profiles so i need a true surface. I downloaded a compressed shape file from the county and need to know how to insert this into a drawing and build a surface using my own surface style.
The files i have to work with:
.dbf
.idx
.prj
.sbn
.sbx
"autocad shape source"
.shp
"autocad complied shape"
I want to create a pyramid with a base of three sides with different lenght. In the end i want to have a solid where i can drag and move the notes to change the hight,lenght and the angle of the sides.
I already managed to draw it in 3d but now i want to convert the drawing into a solid and keep it flexible to change the parameters by draging the notes.
I also tried to extrude a triangle with a specific angle but then i was only able to move the top note up and down changes the hight. Doing it this way the top note also kept beeping in the center-point of the triangle.
Can I make a pyramid has a rectangular base instead of a square?
View 7 Replies View RelatedHow would I create a pyramid where the base and top are rectangles not squares?
View 6 Replies View RelatedI am trying to produce a sketch in 3D of a truncated pyramid, base 11 meters square and top 20 meters square. Its 80 meters high and I need to twist the top 45 degrees to create an iconic tower for a friend in Brazil.
Have drawn the pyramid but how can I twist the top and make the vertical lines follow?
I have a series of boxes or polygones that I would like the program to find the 1/2 distance and create two seperate polylines from the one object.
Example:
I have a square with pt1,pt2, pt3 and pt4 respectively. After I have ran the program it would create a diagonal from pt1 to pt3 and join the rest of the lines now to create the one polyline. Also it would do the same to create another exact polygonal shape for the other half. Thus creating two shapes of equal value from one.
Is there any way to put the 2011 topobase and the 2011 ArcGIS plugin into 2012 or 2013? Seems such a shame just to lost all of that functionality.
View 2 Replies View RelatedI want to create a custom linetype that uses a solid rectangle 0.5wide and 1.0 long. Basically I want to create a shape file from an existing block I have so that I can insert it into the linetype definition. Is there an easy way to do this in ACAD 2009?
View 8 Replies View RelatedI have been trying to create a 3D pyramid using Illustrator CC. All the tutorials I have found have been telling me I need to create a custom bevel, but the Bevels.ai file is not in the plugins folder as it used to be. How do I create a custom bevel in Illustrator CC?
View 9 Replies View Relatedto create a curved shape is. So say you have a rectangular shape running down the left side of the page, but the right side of the shape is curved.
View 6 Replies View RelatedI open a new project and add a layer, then create a rounded rectangle, is there a way to fill just that rounded rectangle with a gradient. I keep getting a message that the layer is not directly editable or something. I need to just play with the thing, I'm sure - eventually I'd porbably sort it all out. But I got a job creating a web page for a mortgage company and I wanted some custom buttons with a gradient fill -
View 2 Replies View RelatedI created this video to achieve this using Xara P&GD. The video is here and the .xar file you need is attached.
This video shows how to create an angle based object for visual presentation, any object created with this method should not be used in manufacturers drawings where precision is paramount.
Alright I am trying to create a shape made up of tons of instances of a symbol (best example of what I am trying to achieve is here )
I hoped I could just use draw inside mode and the symbol sprayer however I am not able to ensure the instances don't colide and that they actually completely fit inside the shape without being cut off.
I am obviously going about this the wrong way but have searched for unsuccessfully for any instruction on how this could be achieved.
Just doing my normal practise in Illustrator. Ive came across designing a dome sphere shape. And Im using the 3d revolve techniqe, So I have my symbol to map onto the 3d elipse. but towards the top of the sphere the symbol tends to get distorted, and it looks aweful. So I also tried another technique to envolope distort with top object but its hard to achieve making it look 3d, because the sphere faces dont go around.
View 13 Replies View RelatedI'm new to illustrator and I'm trying to achieve something I hoped would be quite simple. I want to take a bitmap, live trace it, then create an outline of 2px wide only around the outside limits of the shape. I want to then get rid of all of the live trace vectors and be left with my very simple outline of the original image. Eg.
I've tried image expand, I've tried outline, but nothing seems to work as I need it to.
How can I take these groups of white dots and have them go around the entire object while also taking it's shape?
View 9 Replies View RelatedHow do you draw a truncated pyramid from scratch; notwithstanding the Revit family pyramid?
View 2 Replies View RelatedI'm creating navigational elements in photoshop and I want to be able to adjust the outline by itself, as well as there are some elements that are only an outline with no fill. How do I create shape outlines without the fill?
Adobe Photoshop CS4, PC.
i've scannd somthing, and i want it to look like its behind a glass window.. the object is pressed to the scanner so i got the behind somthing feeling.. now how do i make it look more like a glass window? a glass wall..?
View 9 Replies View Related