Creating a compound curve bullnose ar intersection. Since the entrance is a short distance it is considered the secondary roadway and the looped road the primary. At the intersection of the two roads. I need to provide a compound curve curb return. The configuration is tangent to 25'R to 5'R to tangent with primary road. Need direction/recommendation on best way to input this configuration.
View 3 RepliesConceptual design process for a new subdivision with say 100+ lots, and 5-6 roads within it.
What I'd like is to learn a workflow that lets me adjust the alignments/profile with a minimum amount of effort to re-layout 100+ lots, and which lets us explore design options more interactively. Once we pin down a few alignment options, I would create a simple corridor with multiple baselines to develop the grading concept.
One thing that irks me so far is that the Create ROW command is nice, but it's not dynamic to the alignments.How do you handle cul-de-sacs on this process?
I am new to all these parcel/row and different way of creating a subdivision.
I need to create a right of way of 65' (35' on 1 side, 30' on the other). How can I do that? I had created my alignments not sure how to do this.
I have a huge subdivision that we are about to do in civil 3d. The subdivision has over 1800 lots. I am wondering what is the best way to go about this. At the moment we are thinking we have to do the alignments, profiles and corridors all in one design drawing for it all to be dynamic? If so this file is going to be huge. Is there a way we can split it up and still keep everything dynamic?
View 9 Replies View RelatedI am working on a new subdivision where we made new property lines through an existing property. Is there a way to find out the bearings of the new lines made? The only way I can think to find this information is to dimension the angle and subtract it to get the new bearings.
View 4 Replies View RelatedWhat I have is a highway that is being twinned, however the divided lanes are not consistantly the same distance away (or the same width of roadtop). I would like to keep the number of alignments to a minimum. Both lanes would be based off the same vertical profile. So I would like to have a single assembly that could adjust the median width in the center, and the lane width. Targetting the horizontal layout you can see in the attached screenshot. (this is not all of the job of course)
Is this a feasible task for the targetting assemblys? Would be a fairly standard 4:1 side slopes, adjustable ditch bottom width, 2% crowned road otherwise.
Is there any way to place a full round or bullnose feature on the end of a cylinder without having to use any formulas or pay attention to dimensions similar to the three face selection of the full round fillet option?
Obviously you can take the diameter/2, but the three face selection of the full round fillet is quite simple, and if you didn't originally plan on having the full round it takes extra digging to come up with the right parameter to use.
Is there a way to speed up the entrance of text animation using Elements 10?
View 2 Replies View RelatedIs there as easy way to count the points on a divided line? Example....making contour lines and need to interpolate the points between elevations.
View 3 Replies View RelatedI'm trying to create a Dynamic Block of an 3/4" x 3/4" aluminium angle with holes:
Depending on the length the number of holes will vary.
The distance between each holes need to be somewhere between 8" and a maximum of 12".
The holes must be centered and start from 1 1/2" up to 2" from each ends.
Each distance must be not more precise then 1/16" (no rounded off dimensions)
I'd like to simply drag the handle of the linear parameters (No lookup or visibility for 2 hole, 3 holes, 4 holes etc.)
I have a an angular polyline (not horizontal or vertical). I want to equally divide the polyline with a specified length and get all separation co-ordinates at each interval. The line remains as polyline, I need to get only the co-ordinates of all the possible divisions for a given length.
I need a C#.Net function for this.
Why does Photoshop reckon 0 divided by 0 is 0 when doing arithmetic with colour components?I guess the program logic assumes 0 divided by anything is 0, never proceeding as far as considering that a divisor of 0 is involved. But I wonder if this handling of 0 / 0 is deliberate for a reason that eludes me.
For a non-zero number divided by 0, Photoshop produces the maximum value of a colour component (e.g. 255 in 8 bits). That is sensible and the same result should arise from dividing 0 by 0, surely. (Other graphics software does consider 0 / 0 to produce max.)
Look at the contrived example below. The black disc in Divide mode should result in a white disc, but wherever an underlying colour component is 0, the resulting colour component is 0 instead of max. (Don't bother measuring the pixels in the screenshot - they've been converted from sRGB to my display profile then to sRGB again without infinite precision.)
so this is the most annoying thing ever. I have a subdiv. i turned it to a poly (to get rid of the bloody shell in render view, i dont even know why its showing) when i did this previously, the shell went away when it became a poly, now its not. I'm new to how subdiv's work so am i missing something?
View 1 Replies View RelatedWhat level is it advisable to pose a model. Coz revently I posed at a high mesh level(level 6 subdivision) only to find out that there was a lot of distortion in the arms when i actually brought the model to a lower level after the posing.
View 5 Replies View RelatedI want to split the circle into the seven parts that have same length. Could you teach me an easier way to do that? All I can do is only like this(I did it with my estimation)
View 11 Replies View RelatedMaya 2012 64bit, Win7..I can not convert a polygonal model to subdivision with proxy (command failed),do not see error description in the script editor. What typical problems of convertation (poly->subdiv) do you know ?
View 1 Replies View RelatedI was making a helmet and I deleted right side then in modifier list i chosed symmetry. so far everything was fine but when I finished my helmet and clicked "use Nurms subdivision" helmet made holes in the middle .
View 5 Replies View RelatedAlthough I configured 'scene divided' the VS x3 captured only one file. On another computer the scenes were divided.
View 14 Replies View RelatedI've got a low poly mesh that looks great if sub-divided to level 3.
Is it possible to edit the mesh at level 1 while viewing the mesh sub-divided at level 3 - using Mudbox 2011 or 2012?
I have a character model in Mudbox 2014. I exported the face, body and hands as individual .obj files, each at its maximum subdivision level. But in Mudbox 2013 the sculpting layers are all flattened on the main layer.
Is there an option to keep the sculpting and painting layers intact?
I have run into an issue relating to the differences in the way Mudbox and Maya subdivide meshes. My workflow for creating blend shapes is as follows:
1. Create base head mesh in Maya
2. Import base head mesh into Mudbox and subdivide to level 2
3. Create a Mudbox layer on top of base head mesh to sculpt each blend shape (e.g., browsMidUp)
4. For each blend shape, export the level 0 mesh to Maya for use as a blend shape on the base head mesh
Here is where it all falls apart.
When I smooth the blend shape in Maya (either by choosing smooth preview or by selecting Mesh>Smooth), the smoothed mesh in Maya differs from that in Mudbox. In the case of browsMidUp, the blend shape created in Mudbox only modified the brows. However, in Maya when the blend shape is smoothed the mouth opens up (i.e., the lips smooth differently in Maya than Mudbox, causing the mouth to open).
This is incredibly frustrating because I did not discover this problem until after I created approximately 35 blend shapes in Mudbox!I believe I can work around my current error. However, I would like to know how others approach the creation of blend shapes.Do you use Mudbox? If so, how do prevent issues associated with smoothing differences?
How do you create an alternating curtain panel pattern in a hexagon divided surface curtain wall without individually selecting the panels?
I want the "rows" of hexagons to alternate between solid and void.
I have several images in my project bin, then use the Arrange icon to divide the workspace into "2 up."
There are now two images side by side.
Over the left one are several tabs, although not one for every image (they don't all fit).
Over the right one is a single tab, with the name of the open image.
How do I change which image is shown on the right?
I can change the left one by selecting the left image then double-clicking on the image I want in the project bin.If I try the same on the right, the image I double-click on goes into the left side of the window.I can't pick from tabs, because there aren't any (other than the currently open one) over the right window.
I am using PSE10 with Windows 7. I've looked at the on-line documentation and tutorials, and they don't go into details about controlling the division of the windows.
How do you create a perfect divided portions of two circle like the dial of a clock, it use to be so easy in previous version now in X6
View 5 Replies View RelatedI imported Google earth surface (at eye alt 600m) to civil 3d 2012 and created an alignment of length 181m.
When I exported same alignment to Google earth , it showed the length as 190m ( the difference increases with increase in length of alignment) And also the profile view of the alignment in the Civil D & Google earth varies.
I want to create a Layer Filter that excludes both Civil Layers and Xrefs.
I have created one that excludes Civil objects (Excel Civil.jpg) but when I add a filter for excluding xrefs as well the Civil objects appear in the filter again indeed all the layers are included again (Excel Xref.jpg) if I invert the filter nothing is displayed.
Is it possible to export created surface from civil to revit architecture? If yes , How? And if its not possible - maybe i can somehow import cogo points to revit?
View 6 Replies View RelatedI am trying to work on a previous file in my office, and when it opens on mycomputer, it does not display as it should.
In general, the purpose of the project is to reinstate the side slopes of a road abutting a river. Cut & fill sections have been generated on 20m station increments along the road corridor/surfaces in order to calulate cut and fill as well as to reference the design to flood levels.
When I open the file, all of these sections (and there are alot) have relocated themselves to various locations in model space, none of which are aligned with the viewports that are being used for printing.
Could it be software and/or hardware incompatibility with the computer they were originally created on? (I believe it was created with C3D 2010, or C3D 2011 - I am currently running 2012)
Just curious as to whether people use much colour in their production drawings, particularly for hatches...?
Working for Local Government, we tend to utilise colour hatches to show all kinds of information.
Generally, we have found that colour hatches are a good way to clearly show different areas and materials such as pavements, paths, landscape areas etc. Hatches can then be used to quickly ascertain areas for estimation and our construction team like them too as the plans tend to be easier to read.
The usual arguments about reproduction of plans and slowing down of computers doesn't seem to be an issue for us. Most photocopiers are in colour now anyway and we just make sure that even in black & white the plans are readable.
The way that Civil 3D deals with hatching doesn't seem to slow things down for us either.
Currently using Civil 3D 2013 & 2014 SP1
Right now, the only way I know of being able to see Civil grading objects (surface contours, spot elevations, slopes, etc) while using plain vanilla AutoCAD is to explode everything and export to a lower version.
I'm trying out a trial of AutoCAD 2013 to test things, and my Civil drawing shows up as boxes/text when xrefed into another drawing without doing the task above.
I'm looking for a more efficient way to see grading using AutoCAD (not Civil). Civil is expensive, and I'd like to downgrade the drafters who don't know how to use the Civil functions (and never will), but still need grading to show as a dynamic xref in the background of the drawings they're working on. Problem is, if I have to explode and export my drawing every time I want to update the grading xref in their drawing, it wastes more time than I'd like.
Is this the only way and I have to live with it, or am is there an easier way that I haven't dug up yet? I know I'm not an expert at Civil, so I may be going about this all wrong.
Is there a way to search for a text style in a civil style? I have a text style that our company is trying to get rid of and I would very much like to not have to go through our 72 company styles.
AutoCAD Civil 3D 2014
HP Z620 Workstation 64-bit
Duel Intel Xeon E5-2620 @ 2.00 GHz
Ram: 48 GB