AutoCAD Inventor :: Full Round Fillet / Bullnose On Cylinder
Aug 30, 2013
Is there any way to place a full round or bullnose feature on the end of a cylinder without having to use any formulas or pay attention to dimensions similar to the three face selection of the full round fillet option?
Obviously you can take the diameter/2, but the three face selection of the full round fillet is quite simple, and if you didn't originally plan on having the full round it takes extra digging to come up with the right parameter to use.
View 9 Replies
ADVERTISEMENT
Oct 30, 2011
I'm currently modeling a propeller and i want to fillet the base of the blade to the hub but the way i have it will only let me fillet it towards the patched surface on top of the cylinder, what can I do?
I would also like to have the fillet be a large radii on the center and be small at the leading/trailing edges.I just tried posting it but the file I have available now is bigger than the limit and I cant compress it to 1.5 mb, while I get acces to the file on monday:
The blade is comprised of 2 lofted surfaces and patched surfaces to join them and make a closed loop, one of the patched surfaces ''hugs'' the cilinder outer surface (hub), when I try to fillet the it tries to smooth from the lofted surfaces to the patched surface, making the arc to the other side i want it to.
View 6 Replies
View Related
May 30, 2012
I want to "Fillet" a round angle. If I set the radius and then click the 2 lines then Autocad comes with the message: "Lines are non Coplanar" This problem just started in a drawing i was working in ( 50% were already done by Fillet perfectly ) , I draw only 2D.
View 2 Replies
View Related
Nov 11, 2012
In inventor 2013 I want to extrude a horizontal circle on surface of a bigger vertical hollow cylinder. but what i did it enters into cylinder, and i only want to extrude it on external surface.
View 1 Replies
View Related
Apr 8, 2006
How do I resize a full size photo to fit into a round locket, I'm using CS2.
View 1 Replies
View Related
Sep 1, 2013
Creating a compound curve bullnose ar intersection. Since the entrance is a short distance it is considered the secondary roadway and the looped road the primary. At the intersection of the two roads. I need to provide a compound curve curb return. The configuration is tangent to 25'R to 5'R to tangent with primary road. Need direction/recommendation on best way to input this configuration.
View 3 Replies
View Related
Feb 19, 2012
I have remodeled a part I was working on previously, but now an edge doesn't want to fillet, as it was on the old model ( in the top right corner )..
View 2 Replies
View Related
Oct 11, 2013
I am working on my project at home and I am having some problems with the fillet tool.
Attached is a picture of my problem with what it is doing.
I am trying to fillet A to E and E to C (B to D and D to F also)
On the left hand side when I fillet, it connects C to E instead of A to C and I do not know why it is doing that or what I am doing wrong.
View 2 Replies
View Related
Dec 7, 2011
How do i make the 3mm fillet go in the other direction.When i apply the fillets to the top of the pipes it goes inwards but i want the fillet to go outwards.(like a weld - i don`t want to weld though just use a fillet).
View 1 Replies
View Related
Mar 14, 2012
Is there a way to create smooth transitions for fillet welds for around corners?I have to create four separate fillet welds on all sides of the mating pieces and it breaks at the corners.
View 2 Replies
View Related
Sep 23, 2013
What kind of fillet i need for relax the edges in a eccentric reducer pipes's fitting, i can use fillet of faces for the sircular edge smaller , but am in troubles with the bigger .
View 1 Replies
View Related
May 6, 2013
I have a little issue with drawings where I cannot find out how to highlight fillet edges on the models. I dare say I am missing some simple setup option.
The picture attached shows what I mean. The left is how the model looks in drawing mode and on the right is how I would like it to look (taken from the modelling environment).
View 1 Replies
View Related
Dec 7, 2011
Can you delete part of a fillet feature? While still keeping part of it & adding to it.
I have a fillet feature with 2 fillets to a part. One is in the wrong place.The Feature Fillett1 if you edit it, you will see what I mean.
Keep the middle one. Both fillets are 0.25" / Replace the bottom fillet to the top corner.
I would like to keep the Feature in the order it is in, if possible.
I am using Inventor 2012.
View 2 Replies
View Related
Apr 16, 2013
I have searched the discussion groep and have not came up with any usefull information.
I have an inside web plate sketch that i want to offset but my offset does only do one line at a time.
So my problem basicly is that I want it to do the whole sketch in one click. Is it possible to join all the lines? or is there another function that I do not know of that will do this for me.
Attached is photos of the problem I have
1 picture - How do I join these lines
2 picture - How the whole sketch looks
3 picture - The offset does only do one line at a time (i want it to do the whole sketch)
View 6 Replies
View Related
Sep 14, 2012
I have been asked to change some of the default weld settings within the weldment template, i.e. set groove weld to full face full face, set the fillet weld to 6x6. so that when we do a new weldment these things are already set, have hunted high and low on here, through google, autodesk knowledge base for inventor but havent found anything, not sure if havent put the right keywords in or that it just isnt possible to do.
View 2 Replies
View Related
Sep 15, 2013
I generate 3 points, two lines between point 1,2 and 2,3 and make a bend between the two lines. Cannot do it correctly.
On one side the fillet is not trimmed correctly. I think it is a bug in Inventor. Also when I have the sketch I manually cannot make a decent bend/fillet in the 3D sketch I created.
Private Sub Button1_Click(sender As Object, e As EventArgs) Handles Button1.Click 'add 3d sketchpoints in open partdoc Dim oPartDoc As PartDocument Dim oPartDef As PartComponentDefinition Dim oTG As TransientGeometry oTG = _invApp.TransientGeometry oPartDoc = _invApp.ActiveDocument oPartDef = oPartDoc.ComponentDefinition Dim oSketch As Sketch3D oSketch = oPartDef.Sketches3D.Add() Dim sp1(2) As SketchPoint3D Dim rod(1) As SketchLine3D sp1(0) = oSketch.SketchPoints3D.Add(oTG.CreatePoint(0, 0, 10)) sp1(1) = oSketch.SketchPoints3D.Add(oTG.CreatePoint(0, 0, 0)) sp1(2) = oSketch.SketchPoints3D.Add(oTG.CreatePoint(10, 0, 0)) rod(0) = oSketch.SketchLines3D().AddByTwoPoints(sp1(0).Geometry, sp1(1).Geometry) rod(1) = oSketch.SketchLines3D().AddByTwoPoints(sp1(1).Geometry, sp1(2).Geometry) 'bending it oSketch.SketchArcs3D.AddAsBend(rod(0), rod(1), 2.5) End Sub
The resulting part-file is added, for who wants to try to get a bend with both sides trimmed correctly.
View 2 Replies
View Related
Sep 20, 2011
I need to fillet part on an edge on the top face of the enclosed part, is this possible? I have tried a few things but the fillet command always selects all the edges on the face to fillet.
once selected it says in the selection box that 15 edges are selected, and I can't ctrl click to remove any of them singly, basically it will deselect them all? I have made sure I have loop select off.
View 2 Replies
View Related
Feb 24, 2012
I need to emboss ( cut in ) some grooves into a cylinder, but in such a way, so that they won't get narrower. What do you think would be the best way to do that?
View 2 Replies
View Related
Apr 28, 2012
I have made a sheet metal cylinder with a rip. I am trying to create a seam on this rip as is done in [URL] ....... about half way through.
I have tried to go through the same steps, but I can not select the inside of the rip to built hems and flanges on. I also tried to make the cylinder by sketching 350 degrees of the cylinder instead of creating a rip, This had the same problem.
Why I can't select these edges or how I can work around it?
View 2 Replies
View Related
Mar 10, 2009
How can I create a rib that touches a plane and the end of a cylinder? Inventor will not do it since the thickness of the rib does not touch the cylinder (see attachment).
View 8 Replies
View Related
Feb 16, 2012
i am learning publishing parts to content centre so as to use for frame generator.Success so far except i cannot work out how to change Fillet sizes with the Family Table.As i increase the sizes of beams i want to also control the fillet size within the Family table.Where do i add the fillet parameter?
INV 2012
View 4 Replies
View Related
Mar 23, 2012
I need to show fillet welds between the bar and the curved surface. There is a small gap there (3/8" bar against 2 3/4" O.D. tube) and IV and neither groove or fillet weld works. How to show the weld?
I am using IV2009.
View 1 Replies
View Related
Jan 8, 2013
I am looking for a way to add a welding symbol to an existing fillet weld. When I am creating a fillet weld, I get a chance to create a welding symbol based on the fillet weld size.
If this is not done when the weld is created, there is no way to add this notation. I don't have the "Create Welding Symbol" checkbox when editing an existing weld. The only solution is to delete the weld and recreate it.
I am trying to link the welds in the iam with the weld notes in the idw.
View 1 Replies
View Related
May 8, 2012
I don't understand why this Fillet would fail when it was fine before I changed the length of the edge. See before and after shots attached..
The geometry/features that are used to create the fillet are exactly the same.
View 1 Replies
View Related
Aug 10, 2012
I have a model that has been made up from a revolved sketch and then had loads of bits done to it etc.. Basically it is a tapered ring with a fillet on the top edge, I need a top face dxf export for profiling and to do this I need to remove the radius on the edge, but because it is a revolved sketch and it is not filleted it is not so easy to do with other references involved.
Is there a way I can temporally rebuild the edge to remove the fillet, I tried in fusion but it won't allow a Zero fillet edge?
I can't upload the sketch to show you unfortunately.
View 3 Replies
View Related
Nov 14, 2013
I am building a Crankshaft. How to build the connecting weights that attach the main journals to the connecting rod journals. I can post a screenshot of the design. I have a extruded face that is a half circle on the top.so I am trying to fillet or cut a section off of the rounded edge. I have tried to build tangent workplanes and projecting geomety, but to no avail.
View 9 Replies
View Related
Sep 7, 2011
I am trying real hard to fillet the edges of these designs but it keeps saying try again with a smaller radius.
View 5 Replies
View Related
Oct 10, 2011
I made a fillet earlier and then continued to work on the part. Now when I try to delete the fillet (to replace it with chamfer) Inventor gives me a box: "delete features" and the middle box can be selected which says "dependent sketches and features". If I check the box and hit ok, some of the unreleated holes and chamfers gets deleted and the fillet I wanted to delete doesn't get deleted. If I uncheck the box, different chamfers and threads dissappear, fillet I wanted to delete stays in place again and yellow box appears on the corner of the part. So what should I do to just delete the fillet and keep everything else?
View 4 Replies
View Related
Feb 28, 2013
I am trying to CAD a model rocket I just made so I can test the aerodynamics of it. I have all of the individual parts made in inventor, but I am having trouble getting the fins on the rocket.
How can I constrain the fins (which have a flat face) to the outside of the cylindrical rocket tube? The photo shows the fin and the face (the narrow and long face) that I am trying to constrain to the tube.
View 7 Replies
View Related
Dec 27, 2012
I want to do a simple bend of a cylinder. That is, I have made a 40inch length and want to bend it at several places.
I keep finding a reference to bend part but the tool does not exist in Inventor.
View 3 Replies
View Related
Mar 1, 2012
1. I would like to scribe number of lines in axial direction & around the circumference of a cylinder
2. Secondly, I want those lines to be visible on .idw file so that I can print my drawing
View 2 Replies
View Related
