AutoCAD Architecture :: Crash After Changing Startup Value?
Mar 18, 2013
I changed the 'startup' value from 1 to 2 in ACA 2012, now program crashes. On start up it displays the first error message 3 times (see attached), then opens a blank drawing. Once a select a file it displays the second message 70 times then opens the drawing. After a few seconds a fatal error message is displayed and program closes.
Error messages are the same other than address location changes.
I have tried a repair and a reinstall to no avail.
View 2 Replies
ADVERTISEMENT
Feb 8, 2013
Civil 3D 2013, SP1.
Set STARTUP to 2, and make sure the Sheet Set Manager palette is visible.
Close Civil 3D, then restart it.
It should open in a zero-document state, with the SSM palette visible.
Now open a sheet set, and double click on a sheet in the SSM to open it.
When I do this, I get four "Unhandled Exception" dialogs in a row, then C3D disappears (crashes!)
View 5 Replies
View Related
Jul 10, 2013
I recently gave my windows a factory restore (fresh start windows original copy), I had no issues with autodesk software before the windows fresh start (i use Revit and 3Dmax too), i even installed and used Autocad 2014 on my laptop before the restore and it ran just fine, problem is now after the windows restore Autocad crashes everytime i open it, installation was smooth and succesfull with no error warninings whatsoever; the problem comes when i start Autocad 2014 for the first time, the initialization window opens and starts loading the files but then (everytime) crashes and freezes my laptop forever, not even the task manager is posible to open
My Specs:
Laptop: Alienware M14x R2
Processor: intel i-7 @2.30 ghz
16 gb RAM
Graphics: Nvidia GeForce 650M 2GB
running on Windows 7 64-bit
after the restore i downloaded the latest drivers for my graphics card, so that shouldnt be the issue, i also switched the processing tu GPU only.
i already tried lots of solutions i saw on other posts, but none seems to suit my need, i tried the .NET framework thing, switching off the windows Aero theme, but the problem remains the same, it still freezes completely my laptop everytime i try to run Autocad 2014, i even tried installing Autocad 2013, Autocad 2011 and Revit 2014 but the issue is the same in all of them they freeze at startup without any pop up error warnings, just freezes.
View 6 Replies
View Related
Jan 10, 2013
my tool palette causes a systematic crash at startup .
is there a way to launch without opening toolpalettes .?
View 5 Replies
View Related
Oct 11, 2012
Know it's old, but have been using Photoshop CS 8.0 on office Mac Pro and home iMac for years with no problems. OSX is 10.5.8 Leopard. Still works fine on Mac Pro, but has just started crashing at startup on iMac for no apparent reason. Graphic layout comes up and then shuts down. Reinstalled the application with same result.
View 1 Replies
View Related
Nov 13, 2011
I change my motherboard ans proc and memory yesterday, but i don't reinstall windows seven, and now i don't have time to reinstal windows now.Before change my motherboard, 3ds x64 worked good, and now he crash on startup with the report error on jpeg attachement.
3dsmax_minidump.dmp
dmpuserinfo.xml
dumpdata.zip
(and it's written version 3ds max 13 - 64bits)
But 3ds max 2011 x32 works very good I need 3ds max 2011 x64 for use the plugins hair farm.
I already reinstall a several times 3ds x64 but nothing, et try to remove the three dmp, xml, and zip, and also put on Open GL
windows 7 ultimate x64
intel i7 2600 3.4 ghz
8,00 gb ram
geforce 8800 gt
View 1 Replies
View Related
Nov 25, 2008
OS: vista 64bit (all latest updates)
nvidia 8800gts 512 (driver 180.48)
8 gb RAM + latest mobo bios
It was working totally fine then WHAM! I noticed it first when i minimized it to the taskbar to look for some other files on my desktop. now it suddenly doesn't want to start. the 'only' thing is that the pc went into hibernation while i was at lunch a few times this week (can't see that having an effect)
I start it up and it crashes +/- after 8 seconds. EVERY time.
- Tried using the "run as admin" = didn't work (tried it just in case)
- tried changing a few settings in nvidia control panel = nada!
- once i got it open within the 8 seconds, I turned off openGL completly = nada!
- I've used the "DisallowOpenGLWindows_OFF.reg" just in case and that doesn't work either. (its a pretty recent GFX card)
all other cs4 apps (master suite) are working fine!
this exact same thing happened just before i reinstalled vista x64 about a month ago.
View 39 Replies
View Related
Sep 6, 2008
It crashes before it even finished loading. I haven't even gotten the program to work once. Yes, I uninstalled and reinstalled. I have no printer, and I'm using Vista 64.
This is what it says.
Problem signature:
Problem Event Name: APPCRASH
Application Name: Photoshop.exe
Application Version: 10.0.0.0
Application Timestamp: 4601eae8
Fault Module Name: dlbktwds.ds
Fault Module Version: 3.107.0.0
Fault Module Timestamp: 45df4d5a
Exception Code: c0000005
Exception Offset: 00004da2
OS Version: 6.0.6001.2.1.0.768.3
Locale ID: 1033
Additional Information 1: fd00
Additional Information 2: ea6f5fe8924aaa756324d57f87834160
Additional Information 3: fd00
Additional Information 4: ea6f5fe8924aaa756324d57f87834160
View 28 Replies
View Related
Nov 1, 2013
I get the following crash meassage on booting AE 12.1 from Mavericks
I have re-installed & trashed Prefs.
View 3 Replies
View Related
Nov 29, 2008
In a moment of lax attention I've done something stupid to the Photoshop CS version (original 1) and told it to search C:/programfiles for plugins whereas I meant to tell it specifically where to look.
So now it crashes when it gets to the 'Scanning for Plugins' part and of course I can't alter it back to what it should be.
Now when I run Image Ready the plugins are still as normal...
System Restore doesn't change the settings. Uninstall of the Photoshop component doesn't put it right either.
(maybe uninstall/reinstall the entire CS suite - but I guess even then it will still have the bad settings)
So is it a registry thing and if so what needs to be done to stop it searching the entire hard drive programs for plugins.
View 3 Replies
View Related
Feb 22, 2012
The company I work for has just switched to Max2012 but my machine has a problem with it. I get this error on startup and whenever I open and close the ribbon:
-- Unknown property: "validobjfunc" in #StructolyBoost(undefined:<data>;Public)
It throws open the max script editor window and a message prompt saying the above text. If I press OK, the message goes away. When I close the editor the message comes back and we have a loop!
To get around it I can press OK. Then run script and go to max root > stdplugs > stdscripts > PolyTools.ms
I looked around and saw people had this error on previous versions of max and the fix was to place a copy of polytools.ms in the startup folder. I tried this and polytools.ms crashes instead on startup. To me from the error given it looks like the ribbon isn't loading a script somewhere that it should do. Placing it in the startup folder makes sense as a temporary fix but in this case it doesn't work. I can run the script after every time max has loaded but this is inconvenient and means I can't do any batch operations which I do quite often.
My PC specs are Win XP x64 SP2, Xeon W3550, 12gb ram, quaddro 3800 and dual screen monitors, I also use a Wacom tablet.
The problem happens in both x64 and x86 installations of 3ds max. We have reinstalled 3ds max countless times. My colleagues have identical computers, hardware wise, haven't had the same issues. We're using SP2 patched 3ds max 2012 too.
View 1 Replies
View Related
Aug 26, 2013
I have PSP 15.2.0.12, win 7 64-bit machine with ample power and graphics card. Regularly run multiple CAD programs and so on.
When I double-click the desktop icon to launch the product it crashes - always.
When I double-click an image in Windows Explorer, it launches OK and opens the file with the Edit tab active.
How to resolve the dbl-clk desktop death?
View 4 Replies
View Related
Oct 25, 2011
I though maybe this was a 2010 issue, but here I am in a brand new 2012 setup and experiencing the same problem. For some reason, my toolpalettes disappear on startup and sometimes when switching between projects. I have my workspace saved with the following anchored to the left side of the screen: Properties, External References, Layer manager, Project Navigator
Design Center, and Toolpalettes. When I close Acad (or it closes itself) and restart, sometimes the tool palettes are there and sometimes not. All of the other palettes are there save that one. They also have a habit of reordering themselves if you pin one open and the minimize it it drops to the bottom of the page. Very annoying when you think your PN is at the top, and it isn't, but i digress.
I am working with Windows 7, 64bit, dual screens. This happens with equal frequency in both 10 and 12. (Working in 12 to develop rollout for office and working out kinks. No I do not run them both at the same time.)
One more clue, I noticed in the command history that TOOLPALETTES loads and is followed imediatly by _ToolPalettes.
View 4 Replies
View Related
Aug 8, 2011
Got a problem with tool palettes ever since ACA 2012. When ever I start ACA, I have to push cntrl+3 to show the tool palettes. It's starting to get anoying that I have to do this, and I can't find any setting that will let the tool palettes display on startup.
View 7 Replies
View Related
Jul 29, 2013
I have been getting fatal errors during my user account but not in my admin account. I logged in as admin and repaired Autocad Architecture 2010, using the system disk. I got back the report that Autocad was repaired. However, when I returned to my user account, I get an unhandled expection error when I start up Autocad.Architecture 2010. Do I need to uninstall Autocad Architecture 2010 and then reinstall or should I just pick the option to reinstall Autocad Architecture and then do I have to another registration code?
View 1 Replies
View Related
Oct 25, 2007
we have 2 standard office lisp files that are in our startup suites. the problem we are having is that they don't load when you start ACA so you have to go into the appload dialogue box and click on the load button. then close and restart ACA before they'll work (or drag and drop from the library...
View 2 Replies
View Related
Oct 12, 2012
We just upgraded to 2013 software and anytime i change the ribbon to anything besides the default Inventor crashes.
View 9 Replies
View Related
Dec 2, 2013
This crashing of ACA 2014 on start-up is getting old.
A few times we thought we had it fixed only to have it return with a vengeance.
Seems to crash after loading Project Navigator files. Error log attached.
View 5 Replies
View Related
May 22, 2013
I need to re-install my ACAD 2013. I get to the Product License Activation Options and have the activation code when I first installed. This time it dont work. I bet it something to do with multiple install. Error code is: 0015.11.
View 2 Replies
View Related
Apr 2, 2012
OPEN and then try to browse to another folder and ACA crashes.It first started just when trying to SAVEIMG to save a just rendered to screen image. It would crash consistently when trying to change folders. Did a reinstall and it went away.Came back again and Now it's happening on OPEN as well. Every time. Have to drag files to ACA and save to which ever folder opens and then move it afterwards.I gather that ACA is using the windows folder system and there may be a clash there somewhere. I use AVG antivirus and I guess it's possible it is doing something like checking folders and causing problems.It has caused the browsers (IE and Chrome) to crash.Added an ignore acad.exe and whole folder to AVG but it still crashes.
Win7 sp1 64bit, 16gb RAM Core7 i7-2600 @ 3400ghz
View 4 Replies
View Related
Dec 10, 2010
I was using the 'Isolate Objects in Plan' on my Model when I experienced a fatal error, and my system went down. So I went to my latest Autosave and opened it back up, only lost 5 minutes at the most. No, big deal, right?
But now I have objects missing, and when I go to save it says...
..."Save command is not allowed when edit in view session is active"...
It must still be in Edit in view, the only problem is that the small dialog box which takes me out of edit in view is missing. So, how am I supposed to exit this session? I have nothing active in the ribbon, nothing in the tabs a the bottom of the screen.
View 3 Replies
View Related
Nov 16, 2010
I am using Windows 7 Pro (64-Bit) with Autodesk Inv 2011 (64-Bit).
I normally use this feature: "Realistic Appearance" and changing the material. However, when I accept (Clicked OK), the application crashed on me!
Please take a look at the error and the image...
Problem signature:
Problem Event Name: APPCRASH
Application Name: Inventor.exe
Application Version: 15.1.0.28200
Application Timestamp: 4c5b0492
Fault Module Name: ntdll.dll
[Code] ....
View 7 Replies
View Related
Mar 17, 2013
Everything you read says that to change the default AI (CS3) startup document you use this path:
Users > (User Name) > Library > Application Support > Adobe > Adobe Illustrator CS3 > New Document Profiles > *.ai
The problem is, under Mountain Lion that path doesn't exist. When I go to my user name, there is no "Library" folder at all. Under "Shared" there is an AI Library folder, but it has nothing of any value in it.
My AI startup document (that I've been using for ages) is found here:
HD > Applications > Adobe Illustrator CS3 > Plug-ins > filename.ai
However, if I navigate there and make changes, then quit Illustrator and re-launch it, nothing happens. I'm using the same old defaults as before. I know I need to upgrade to a later version of CS, but the prices have become so outrageous there's no way I can justify it as long as AI and PS are working. You need a mortgage to buy new Adobe products these days.
View 3 Replies
View Related
Mar 17, 2012
Both Photoshop CS5 (64 Bit) and Premiere Pro (64 Bit) Crash on Start up. 32 bit version of Photoshop works fine.
Here is the problem signature when they crash.
Problem signature:
Problem Event Name: APPCRASH
Application Name: Photoshop.exe
Application Version: 12.0.0.0
Application Timestamp: 4bbc5b10
Fault Module Name: CoolType.dll
Fault Module Version: 5.7.82.7602
Fault Module Timestamp: 4b980c97
[code]....
Both are referencing cooltype.dll. I ran Font Doctor on all system and non-system fonts and found no errors. Booted without Extensis Suitcase loading. Nothing works. All 32 bit programs work fine.
View 8 Replies
View Related
Jun 27, 2012
When a user closes ACA 2012 (sp2)he gets an empty crash message.
We are running win7 64bit.
View 2 Replies
View Related
Jan 17, 2013
Photoshop acting weird. I open it to make logo and I New document and I go to the text tool and click the fonts and it crashes. URL....
View 4 Replies
View Related
Feb 3, 2014
I select an audio clip in timeline to open it in Source Window.
I try to change the IN POINT from inside the Source Window and I crash. Every time.
Then I click CONTINUE and get this:
I am running PPCC 7.2.2 (4) on a MacPro with 10.8.5 installed.
View 6 Replies
View Related
May 30, 2011
How make changing in my operational system that I had chosen. I clicked on 32 mbit but know I want to have 64 mbit. I didn't install software yet, it is still waiting to install.
View 2 Replies
View Related
May 4, 2012
If I create a drawing in AutoCAD Architecture 2010 on a 64 bit machine is there any way I can still plot using my old 32 bit printers?
I'm thinking print to dwf or PDF then open the file on my old 32 bit machine for printing?
View 1 Replies
View Related
Dec 11, 2012
I'm almost done with my elevations! One last thing, though.... When I print it, it comes out all green. Is there anyway for me to change the colors so it's just black and white? Also, when I print it, there's a line between my 1st floor roof, my floor joist, and the floor for my 2nd story. Is there any way I can get rid of that, such as joining the walls? I'm using AutoCAD Architecture 2013.
View 3 Replies
View Related
Jan 17, 2012
I am currently using Autocad Architecture 2010 and would like to change the rendering options if possible. I have drawn something and can view it in realistic style, but when I render it, the lighting comes into play and everything looks too light. What I would like to know is how could I render my drawing in realistic view so that the rendering reflects what is on my screen in model space? Or realistic sketchy view for that matter?
View 1 Replies
View Related
