When I initiate the trim command with a double enter (i.e. select all mode), I usually first zoom into the area I want to trim so I see no other objects, then start the trim <Enter><Enter> option, then pick the lines I want to trim. Even if these extend off the screen and cross other objects (not seen on the screen), they usually trim off completely. However, on occassion they don't. To replicate the problem try this:
Draw 2 vertical lines and 2 horizontal intersecting (like noughts and crosses)Draw a horizontal line that intersects both vertical lines but up near the top of those linesZoom in so you only see the square and extending lines (but not the short horizontal line)Trim <Enter> <Enter> and pick from bottom right to top left (i.e. around the squareZoom out.
The square is trimmed, however there are 2 line fragments left above the horizontal short line.
Fix: UndoTrim the same way and presto, it now works I found if I then moved the line above (so only a small amount), zoomed in again, tried to trim - same error.
We recently upgraded to Autocad Architecture 2013 and the trim command is driving me mental. Lets say I have a window mullion pattern with 4 intersecting lines and I want to trim out the center. (see attached example) I start the trim command, then right to left window to select the 4 lines, then use another right to left selection window to trim out the lines. It always leaves on of the lines leaving me to have to click one more time. This is a huge pain when you have to do this multiple times. That is a lot of extra clicks. What gives? I never had this issue before.
Noticed a change in the trim command between 2013 & 2014?
In 2013 (with out selecting trim all) the trim line didn't have to intersect the line you wanted to trim. We just upgraded to 2014 and I noticed that if I want to trim a line that the lines have to intersect. A line that doesn't intersect with the selected trim line will not trim.
The yellowcurve is created by progect geometry of red circle on a solid(I delete solid after that).and there are some lines on circle and parallel to projection vector. now I,m going to trim or extend these lines by yellow curve. trim and extend don,t work and there is no intersection point between blue lines and yellow cure . What should I do?
I am having trouble with my lines connecting...have tried adjusting the line effects, edge mode, jitter, line extension...but Trim and Facet are not working with certain lines not connecting or not trimming. I attached my dwg file.
I produce a lot of "Exploded View" style drawings for our equipment for assembly drawings and Operators Manuals. I model everything in 3D, set the perspective view, adjust the view I like, then use the Flatshot command to make 2D lines and arcs verions of the view to put into paperspace. Then item bubbles, notes, whatever. as of the last week, my flatshots, if they include a hex bolt head in the view, the arcs on the faces of the flats will be really stretched and skewed decidley toward the vanishing point in the completion of the Flatshot command. It does not happen on other arcs that may be in the model, seems to be exclusive with the hex. I doesn't happen if I do not make the view pespective but leave it "Parallell".
I'm working on this model and I am trying to use the surface trim command in cad 2011, but its not working and its pissing me off. I want to use the trim and use the dome in my model as the cutting edge to cut the parts of the curved walls that fall inside the dome but it is not working. I have the file uploaded.
I have a drawing of tower in 3d, i want to put all the drawing in 2d only so that i can trim some part of the lines, is it possible to put the 3d in 2d in one level only, i mean one axis.
I have a drawing from a surveyor showing contours which have been formed by 2D polylines. I have tried to trim out a portion of the contours, which i don't need, using extrim command but it doesn't trim any of the contour lines. Even with just the trim command i cannot trim them. i have tied exploding but still not managed to trim. How to trim these unwanted contour lines ?
I'm using ACA 2008 and used to be able to pick two lines that didn't physically cross each other and use the trim command to trim them based on where they would cross if they extended to each other. But it doesn't seem to do it anymore.
Best way I can describe it is it used to trim at the apparent interest ion of where they would come together. I'm sure there's some easy fix to this, just don't know where it's at.
I have drawn figure1 with rectangle and press/pull command. I have drawn figure2 with line command. I want to trim the lines of figure1 which are shown in red color in figure2.How to do this?
I drew 2 circles with ttr command (1 and 2). The problem is when I try to trim them to remove the part I don't need, it doesn't work cause the circles 1 and 2 aren't stick with the borders as they should. At the 4 red circle points, if you zoom you'll notice they don't stick the border, never faced this problem before (usually I cut the part I don't need without problem). I've done regen/all but doesn't seem to fix that problem.
I want to trim off the top of the lines in the picture below. I used white lines to cover the top to show you what look I wanted to achieve, However, I know that using white lines to cover it up is not a practical solution for my application. I know that I should be messing with the pathfinder tool but I just can't get it to work right for me. I am pretty new to illustrator and Photoshop.
I'm trying to learn illustrator cs2 on my own and am having some issues with a few basic functions. I am drawing shapes using the rectangle, ellipses and trying to join them together. How do i trim 2 lines together to make a corner. I would like to cut off the exess at the ends by cutting to the other lines. I know this seems basic but I can't figure it out. In the end I want to make a figure using all the drawing tools ( pen, line, shapes etc) and have the outline just one feature.
I m working in autoCAD'13. I have got this drawing from a client. I need to trim these surfaces to get only the outer surfaces. But since these are not intersecting at right angles, i m not able to trim these surfaces.
Please find attached a small part of the concerned drawing. The intersecting surfaces in the drawing have to be trimmed.
After installing the VBA Module, I get the message "Unknown command "VBARUN"". I've rebooted, restarted and tried reinstalling the VBA Module to no avail.
I press CTRL+9 to make the Command Line disappear while drawing. When I plot (or when doing a plot preview) , the Command Line appears again by itself. So I always have to turn the Command Line off manually after each plot
The bug still happens;
- if Dynamic Input is turned off or on - if I plot to a real device or in PDF - if the Cammand Line Palette i docked or floating.
This is not an issue in AutoCAD 2012 so I guess it has to do with the new way they programmed the revamped Command Line palette in 2013.
Is it possible to trim a 3d solid using another 3d solid as a cutting edge? I want to cut the edges of a dam using the natural ground surface (which is also a solid) as my cutting edge.
1. is there a faster way or command to which lines are flying?coz i got this file from a collegue and i was wondering why is it that lines doesnt connide each other... so when i tilt the file into front elevation... i saw all the lines were not on the same elevation.. so what i did is to change the value of Z into zero....
2. does i press something... i used to select the object, pan and drag ( to select and add more on my selected objects.).now if i select the object and use the center of my mouse to drag... point were gone out... so i input first the command then select and drag..
Everytime I use the label line command, when I go to plot my drawing I see a box around my label and the label is either chopped off or missing. A rectangle prints out around where the label is.
Okay. So our designer is using autocad 2013. He is using a pc and he is sending me the files (i'm on a mac) and the thinest lines do not show or print. But, they print/show on a pc! I need to be able to print these. I've searched the web and found nothing.
I face new problem in using solid hatch command ,when I choose poly lines and use hatch some unwanted lines appears inside hatch area which make my shape separate from others part be meant be unify. I am amateur in using auto cad .BTW , my scale is about 5 micron meter and when I export the drawing int pdf all straight lines become curvy .I upload the image which describe itself my problem. URLs...
