I am having trouble with my lines connecting...have tried adjusting the line effects, edge mode, jitter, line extension...but Trim and Facet are not working with certain lines not connecting or not trimming. I attached my dwg file.
View 2 RepliesThe yellowcurve is created by progect geometry of red circle on a solid(I delete solid after that).and there are some lines on circle and parallel to projection vector. now I,m going to trim or extend these lines by yellow curve. trim and extend don,t work and there is no intersection point between blue lines and yellow cure . What should I do?
View 4 Replies View RelatedWhen I initiate the trim command with a double enter (i.e. select all mode), I usually first zoom into the area I want to trim so I see no other objects, then start the trim <Enter><Enter> option, then pick the lines I want to trim. Even if these extend off the screen and cross other objects (not seen on the screen), they usually trim off completely. However, on occassion they don't. To replicate the problem try this:
Draw 2 vertical lines and 2 horizontal intersecting (like noughts and crosses)Draw a horizontal line that intersects both vertical lines but up near the top of those linesZoom in so you only see the square and extending lines (but not the short horizontal line)Trim <Enter> <Enter> and pick from bottom right to top left (i.e. around the squareZoom out.
The square is trimmed, however there are 2 line fragments left above the horizontal short line.
Fix: UndoTrim the same way and presto, it now works I found if I then moved the line above (so only a small amount), zoomed in again, tried to trim - same error.
I posted a file drawing of a basic symbol.....how do i trim the circle segment between the 2 red lines?
I have drawn this symbol in space....should i be anchoring it to the 0,0 co-ordinates?
Im having a little issue with connecting lines and circles but not sure how to shorten the question to do a search on here. I have 2 concentric circles (the two circles form the walls of a round tower wall) which have 2 lines (representing a wall) passing through them. I want to join the circles from the circumference to the lines, but each time I try to do it the line seems to default to the center of the circles and to the endpoints of the lines which is not what I want. The eventual aim will be to remove a section of the circles and the lines where the new line connects to them to form an opening in the walls.
Ive tried <shift>right click and selecting tangent on the circles but I cant figure out what to do on the lines and it constantly defaults to the end of the line not to where I want to intersect the lines.
Trim tool errors when cutting lines with lines CorelDraw X6
View 1 Replies View RelatedI use splines a lot to provide a contiuous smooth curve between two lines which are co-planar. The splines are drawn by connecting the ends of the two lines and then the tangent direction set by hovering over the end grips. I then use the FLATEN command to convert these splines to polylines that can have their lineweights set to a value other than 0. My problem is that sometimes when i use the FLATTEN command, the spline is erased.
View 7 Replies View RelatedHow or where I can get the Detail tools that was in the 2013 Tool Palette?
Batt insulation
drywall
Plywood
studs
pretty much everything you need to build a detail. Where are these tools?
I need to connect a rapport with others(print on fabric for textile industry). It looks like a mosaic, however the pieces doesn't connect side by side at the same height, but side by side sometimes higher, sometimes lower.
The thing is: when I try put then together the limit of the layers create an edge that prevents connection. I'm sending some images to try to make this clear: 1- all layers together with the thin line between the 2- closer to junction 3- closer 3200% to see what really happens.
I am trying to make a series of curved walls with windows in them as I place the windows they do not place into the walls because of breaks in the wall line between them. I have atempted to make a line out of the wall and convert the line into one single wall segment but it always breaks back down to the geometry of arc+ arc+circle exctra is there a way to make the wall one single wall or to make a series of arcs into a single polyline so I can convert it into a wall face?
View 1 Replies View RelatedI have a drawing of tower in 3d, i want to put all the drawing in 2d only so that i can trim some part of the lines, is it possible to put the 3d in 2d in one level only, i mean one axis.
View 9 Replies View RelatedI have a drawing from a surveyor showing contours which have been formed by 2D polylines. I have tried to trim out a portion of the contours, which i don't need, using extrim command but it doesn't trim any of the contour lines. Even with just the trim command i cannot trim them. i have tied exploding but still not managed to trim. How to trim these unwanted contour lines ?
View 5 Replies View RelatedIf you have a solid a there are inner lines you want to trim how do you do that in autocad 2013.
View 9 Replies View RelatedI need to create two separate enclosed objects (a & b) – both of which individually can be reduced/increased in size using the contour tool.
I initially created a rounded oblong shape and added two wavy lines. I'm having trouble removing the unneeded horizontal lines and connecting the other lines up.
I'm using ACA 2008 and used to be able to pick two lines that didn't physically cross each other and use the trim command to trim them based on where they would cross if they extended to each other. But it doesn't seem to do it anymore.
Best way I can describe it is it used to trim at the apparent interest ion of where they would come together. I'm sure there's some easy fix to this, just don't know where it's at.
We recently upgraded to Autocad Architecture 2013 and the trim command is driving me mental. Lets say I have a window mullion pattern with 4 intersecting lines and I want to trim out the center. (see attached example) I start the trim command, then right to left window to select the 4 lines, then use another right to left selection window to trim out the lines. It always leaves on of the lines leaving me to have to click one more time. This is a huge pain when you have to do this multiple times. That is a lot of extra clicks. What gives? I never had this issue before.
View 5 Replies View RelatedI have drawn figure1 with rectangle and press/pull command. I have drawn figure2 with line command. I want to trim the lines of figure1 which are shown in red color in figure2.How to do this?
View 4 Replies View RelatedI drew 2 circles with ttr command (1 and 2). The problem is when I try to trim them to remove the part I don't need, it doesn't work cause the circles 1 and 2 aren't stick with the borders as they should. At the 4 red circle points, if you zoom you'll notice they don't stick the border, never faced this problem before (usually I cut the part I don't need without problem). I've done regen/all but doesn't seem to fix that problem.
View 9 Replies View RelatedI want to trim off the top of the lines in the picture below. I used white lines to cover the top to show you what look I wanted to achieve, However, I know that using white lines to cover it up is not a practical solution for my application. I know that I should be messing with the pathfinder tool but I just can't get it to work right for me. I am pretty new to illustrator and Photoshop.
View 2 Replies View RelatedI'm a Autocad 3D newbie! How to trim a solid from a sphere. well here's an image that will explain better!( it's the pink part from the green) .
View 8 Replies View RelatedI'm trying to learn illustrator cs2 on my own and am having some issues with a few basic functions. I am drawing shapes using the rectangle, ellipses and trying to join them together. How do i trim 2 lines together to make a corner. I would like to cut off the exess at the ends by cutting to the other lines. I know this seems basic but I can't figure it out. In the end I want to make a figure using all the drawing tools ( pen, line, shapes etc) and have the outline just one feature.
View 8 Replies View RelatedI m working in autoCAD'13. I have got this drawing from a client. I need to trim these surfaces to get only the outer surfaces. But since these are not intersecting at right angles, i m not able to trim these surfaces.
Please find attached a small part of the concerned drawing. The intersecting surfaces in the drawing have to be trimmed.
Noticed a change in the trim command between 2013 & 2014?
In 2013 (with out selecting trim all) the trim line didn't have to intersect the line you wanted to trim. We just upgraded to 2014 and I noticed that if I want to trim a line that the lines have to intersect. A line that doesn't intersect with the selected trim line will not trim.
I am an SL netizen, SL being SecondLife. I did a couple of earrings and gave them to a friend to sell and he says I should go into jewelry making. I do have a little experience in PS as I already make t shirts for sale in SL. But jewelry making... I am a little lost on making the jewels and gems. The primitive part will be easy, but I'll need the textures to put onto the facets, and this is where this delightful forum and my post comes into play. How do I do gem / jewel facet textures?
This is some jewelry I bought earlier...
how she did it would be a faux pas, like asking Mars Candies how they make M&Ms, ya know? But I hope with someone's help I can make my own just as good version for using on my own jewelry.
I draw a rectangle, and I want to draw a line coming out from the rectangle. Normally I would use OSNAP to get midpoint and endpoint, but this time I want to draw it from any part of the edges of the rectangle.
How do I get the cursor to "snap" to the lines of the rectangle? Similarly, I would like this function for the MOVE tool as well, I used this method in Sketchup before and really liked it a lot.
How do I achieve this in AutoCAD? I tried Nearest, Perpendicular, but they don't work as well.
edit: just found out my subject line is not related .
Total buffoon when it comes to getting GIMP to do what I want to do. I'm just practicing with making maps, black lines on a white background, and I've run into some issues I'm wondering if I can get rectified.
1) For whatever reason, the line weight of everything has shifted throughout the file, ending with some lines lighter and grayer than others. Is there a way I can get GIMP to trace all the lines in a uniform black, with uniform thickness?
2) I have tried locking the white background, but often when I select and move my black lines, if I don't click in just the right spot it moves the white background instead, which is really, reeeaaaly aggravating. How Do I get that background to be completely untouchable?
3) In trying to colour the image, I've run into problems with their being a white outline between the colour and the black lines. I think I need to sharpen the image or somesuch? How can one correct this issue?
4) Is there anyway to convert the black dotted lines of the paths tools into straight black lines, in regards to an older file? If not, is there an easy way to trace them?
5) I find the scale too tends to make my image too jagged. I want to take a section of my map, move it too another file and enlarge it to do detail work - what's the best way to do this in order to have a clear image?
6) Any way to translate an image from a MErcator Projection ot a Winkell-Trippel projection, one that works on a Mac?
Open options window from menu Tools>Options (or shortcut Ctrl+J)
Go Workspace area and select Edit.
There are some options for users. And tehere is Minimum extrude facet size . What is it? How it use?
BonusTools 2013 menu doesn't show in maya 2013,how can show it.
View 3 Replies View RelatedIs it possible to trim a 3d solid using another 3d solid as a cutting edge? I want to cut the edges of a dam using the natural ground surface (which is also a solid) as my cutting edge.
View 3 Replies View RelatedWhen I search on Express Tools in the Help section I am told to type EXPRESS TOOLS int the Command Line. That produces the error msg. no such command.
View 2 Replies View RelatedUsing Autocad 2013 I'm having this massive slow down when I choose a tool such as trim. All I have to do is select the trim (or chamfer etc) button for example and it's as though I get a framerate of about 5. I've never had a problem in 2012.
Rough pc specs:
win7 x64
8gb ram
i3-2100 3.1ghz
amd radeon hd 6700 (latest drivers installed)
The pc specs are fine - perhaps an issue with the graphic card?