The bread shaped object is a structural concrete column with two corners rounded.
Why can I see the new wall's lines ghosted through a structural column?
AutoCAD 2010
AutoCAD LT 2013
Revit Architecture LT 2013
I have to draw a bulkhead wall that connects to a full height wall and a gyp bd ceiling. This causes the entire end of the full height wall to skew in line with the butt joint above the ceiling level. I tried Wall Joins but all the options screw up the bottom half of the wall which needs to remain in line with the paired opposite. I also tried editing the sketch of the wall profile but Revit couldn't keep the elements joined. I tried trimming the two walls back together afterwards but the wall profile dominates and prevents a clean join above the ceiling.
Surely there's a way to have different kinds of joins at different heights?
Created a family with category 'column' in order to make in room bounding.
This family is basicly some extrusions. nothing fancy about that. However when placed in my model these extusions merge with the wall and inherit their properties which I don't want.
I am doing a five stories building and when ad the structural column with concrete cast in place material, the representation in plan view does not cover the block hatch of the wall. See attached image. I have read all about structural columns and did not find any solution.
View 5 Replies View RelatedI am having trouble placing a wall foundation under a curtain wall in my project. Revit says that a foundation has been added but it is not visible in any view. I've tried editing the visiblity properties but that didn't fix the probelm.
View 3 Replies View RelatedI'm trying to make a Wall Types Legend using the Legend function in 2011. I did the first wall type just fine, placed it in section, tagged the material, etc. Now when I go to place another wall in a section view, it tells me the component is not visible in selected view. They are both new construction phase, stacked walls.
View 3 Replies View RelatedI have some families in a project such as sinks and cabinets that are wall hosted, but when I try to place them on the existing walls of the linked file they do not go there. Is there a setting to get around this?
View 1 Replies View RelatedIs there a way to demolish (new construction) an opening into a wall that is an existing phase (existing wall)?
View 6 Replies View RelatedI have drawn an existing building thats needs a renovation. In the project i need to add 100mm insulation to the external side of the outer walls. Are there any way that i can add theese 100mm to my existing walls but only show the new 100mm in new construction ?
View 1 Replies View RelatedI have a problem inserting the slanted columns when I use the "Beam/Column joints" commando. When I insert the slanted column, the beams are divided.
It should look like picture 1, but it always ends up as image 2. How can I solve this?
Any way to get a wall sweep that's set up in the type/structure properties to follow a wall if that walls profile has changed. For example, in the image below, I've split the wall and adjusted it's profile to create some cheesy angled parapet. How do i get my wall cap to follow along? I thought splitting it and changing it's height would work, but no. And if I change the profile without splitting the wall the wall cap just runs right through the wall, as if the profiel was never even changed.
View 3 Replies View RelatedI am trying to align the curtain wall with the edge of the concrete slab/face of wood framed wall (Core). I have tried to align and move however the whole wall moves as well as the edge of the slab. How I can move the Curtain wall leaving the other elements in place?
View 2 Replies View RelatedRefer to the attached file. How can I cut the RED part of the Wall 1 (W1) , where Wall 2 is sloped. I also want to cut a hole in wall 2 (W2) by the BLUE rectangle , but why I can't do that .
I also want to add a second floor to my project but I can only see the" Level" icon goes grey and I can't click it.
When I try to change the length of a wall it grows at both end. How to grow at one end only?
When I change the wall type to one with a different thickness, I cannot control which face of the wall remains fixed and which face moves. eg: change from 130mm to 250mm screws up my room width. How do I do this?
I am trying to make a floorplan of my house in Revit 2013, but I am having an issue when it comes to one wall in my house. I have an opening in the Master Bedroom that leads to the bathroom. This wall has a weird arched-like opening in it and I have no clue how to make this in Revit. I have attached a sketch.
Also, my exterior walls are 7' tall but the interior walls start at 7' and go up to 8' once in the middle of the house and reduce back to 7". How does one set that up in Revit?
EDIT: May have made the image too small to see, but the top is not arched, it is actually half of a decagon.
I have a question about wall profiles. I want to make a profile on a wall so I can make Zinc Panels on the wall that are 10" X 20". I've attached a picture of what I'm going for. I'd like it to have a 1/2" spacing between them and with a joint depth of 1" and I'd like to do this is the wall type so that I can use this wall in multiple places rather than having it model-in-place. Anyway I have made a profile that is 1" X 10" so that it can become my panel profile. But when I go to add it to the wall as a wall sweep as I have seen people do I get hung up on how to make it tile up the wall and also I don't understand how to make the profile so that it is 20" wide. I have a screen shot of where I'm editing this too. Below is the link of the site.
View 8 Replies View Related“Drag wall end” to the edge of the wall (indicated),In the attached screenshot, I wanted to drag the end of the temporary dimension from its location to the end edge of the wall but sounds not to respond!
How this temporary dimension can be dragged to the edge of the wall?
I have a feature line as the top of a wall and want to grade up away from it to marry to existing ground.
View 1 Replies View RelatedI can create structural column schedule but i cant create for architectural columns.i wonder that i do something wrong or simply i cant be done?
View 1 Replies View RelatedWhen i load my column it follow wall hatching. How i'm going to remove the hatching from my column.
View 2 Replies View RelatedI am having trouble creating my own column and beam
structural column schedule
structural framing schedule
i do not know the settings to be ticked for me to create the schedules and make them appear after i create new scheduling...
also i want to know how the graphical column and beam works...
then setting the level in the schedule to make them reflect instead of using the comments section...
Attach here is a screenshot of the levels...
I am doing the structural frame of a house with curved walls and I needed to use the Model in Place command to create a curve shaped column. I defined it's category as Structural Column, but it takes the fill pattern of the wall. When I isolate the column, it has the same fill pattern as the column from the library. I need that the column will be displayed as the other structural column.
View 1 Replies View RelatedI am trying to model a column to a curved profile as shown in my sketch. I have opened the structural Column family and imported the curve profile i require it to follow om my required work plane and tried to model a sweep but i'm having problems...
The Sweep will not follow the line of the profile and the column is offset.
Look at the images.
How can we calculate the formwork of column & beam? Is it possible to add "Height" parameter in Column. Because we add formula into the Family file as below:
Perimeter = (2*Depth+2*Width)
Formwork Area = Perimeter*Height
Revit Arch 2012. I've got some large grids in the model and need to adjust their 2d extends in a matchline plan. However every time I try to do so, I receive the "Element is too small on screen" error.
Screencast of error in action.
[URL]
I mentioned in the vid that the grids were Copy/Monitor'ed from "another drawing"... I meant another model.
How to add this steel base plate, to a HSS column?
Actual column specs attached
I have Revit 2014 MEP
How can i draw column like this >>
View 1 Replies View RelatedHow to calculate Column quantity and gross volume.
View 8 Replies View RelatedI'd like to change the line thickness of these structural columns, but changing the view graphics doesn't override.
View 3 Replies View RelatedIn Bill of material i have custom PartQty column and is beside QTY column. I need all informations from QTY column to PartQty column to copy. Possible with iLogic? I'm selecting now manualy copy and paste but it would be nice to have automatic.
View 9 Replies View RelatedIs there anyway no wall gap line between floor when I copy 1st floor walls to 2nd floor. Not to use "Join geometry" & Line work: invisible line" tools? See attached picture.
View 3 Replies View Related