Created a family with category 'column' in order to make in room bounding.
This family is basicly some extrusions. nothing fancy about that. However when placed in my model these extusions merge with the wall and inherit their properties which I don't want.
I have to draw a bulkhead wall that connects to a full height wall and a gyp bd ceiling. This causes the entire end of the full height wall to skew in line with the butt joint above the ceiling level. I tried Wall Joins but all the options screw up the bottom half of the wall which needs to remain in line with the paired opposite. I also tried editing the sketch of the wall profile but Revit couldn't keep the elements joined. I tried trimming the two walls back together afterwards but the wall profile dominates and prevents a clean join above the ceiling.
Surely there's a way to have different kinds of joins at different heights?
I have 2 corners between 3 walls, one of which is of an odd construction. I want the outer layers of the two side walls to meet as they do when trimmed to each other but this creates a bit of angled wall inside the room on the upper left. I want that corner to look like the left and top walls are trimmed. The two corners are too far apart for wall join to clean the whole intersection and I can't really move any of these walls.
Here's a video of trimming the walls.
AutoCAD 2010
AutoCAD LT 2013
Revit Architecture LT 2013
I've been added and removed specific mullions along curtain wall grid lines and now have the mullions where I want them. Unfortunately, some of the glass panels remain divided along the grid lines even though the mullions have been removed. Is there some way to join the two panels into one?
View 9 Replies View RelatedI am drawing up my house in Revit to get use to the software. I created my house, and now my garage. I selected to create a roof by footprint but when I tried to join the roof to the adjacent wall, the overhang does not follow. I then selected the overhang to join to the adjacent wall but an error pops up: "Part of the roof to be joined misses the target face."
I attached a PDF of the roof.Also, you will notice a line that separates the two walls I joined together. I may separate them but how do I avoid this if I want to make one solid wall?
As for the wall selection, I have vinyl siding and would like to use properties that relate when selecting my exterior walls. I do not see anything regarding that besides wood siding. I thought that should be in my properties when I downloaded and purchased the software.
I'm trying to Join First and Second Floor walls that are interrupted by floor framing. I've separated sheathing and siding layers and extended these over to the lower wall. All looks good, except for the joint line. In section view, I use Join Geometry tool and it works, the joint is gone. However on Elevation and 3D viiews the line is still there.
View 2 Replies View RelatedIs it possible to create the Wall family in revit?
View 5 Replies View RelatedThe bread shaped object is a structural concrete column with two corners rounded.
Why can I see the new wall's lines ghosted through a structural column?
AutoCAD 2010
AutoCAD LT 2013
Revit Architecture LT 2013
I am creating a fireplace family in Revit Architecture 2012 with wall host (Speciality equipment with Wall host). I selected the template created the family, but in mean time i can't understand the wall is having delete option.(i.e it is released from host). I am surprised to see that in the family type, the wall host is missing.
View 1 Replies View RelatedI want to Create a Wall Nitch that will be in a tiled shower we are doing. Best way to create a family that cuts into a wall? I don't want to Create an opening, because I don't want it going all the way through the wall.
View 4 Replies View RelatedI would like to cut a void into the wall of a host window family. When I place a void in the family, it does not cut thought the wall.
I tried making the void on a plane perpendicular and parallel to the wall plane. I dont know if this has anything to do with how voids work. But its not working. I also dont have an 'opening' element in the window family.
I would like to create a family component using the wall foundation bearing footing as a template. I cannot find the file where the templates are located. I tried using the structural footing template but it would not give me the same flexibility the wall foundation bearing footing template does.
View 2 Replies View RelatedI don't know if this is possible, but can a door family read the rating of a wall and also have it read in the door schedule? I have tried applying a shared parameter on the door family and adding it in the project. I am not understanding how I can link the two together.
View 2 Replies View RelatedI am trying to build a curtain wall panel family (see attached). I want the extremities of the solids to be glued to the surrounding frame. I want to be able to scale the model inside the frame with different curtain wall panel system sizes. 5'x4', 6'x8' etc... I am having problems with restricted constraints. I do not know what I am doing wrong. the model inside the panel are created from soild extrusions. if I align the solid extrusion from one side of the frame , only that side will grow or shrink with frame, and makes the model look weird. I tried to group the solids with reference lines in them glued to the reference line grid i created in the panel and that did not work. I want to be to scale proportionally the model inside the panel.
View 6 Replies View RelatedI am creating a folding door model and would like to use a parameter called EXERIOR WALL OFFSET. I have used this parameter before but am having trouble getting it to work within my family. The only difference is that I created one frame/jamb instead of 4 seperate profiles. The question is, why can't i get the jamb to move within the wall using the exterior wall offset parameter? It seems to move the sash/panels just fine but the jamb is constrainted somehow.
View 1 Replies View RelatedI am working on my first real Revit project. i need to modify a windows family and in particular i want to change the axis of insertion of the window in the wall. I mean... my window should be placed on the outer edge of my wall. i try to unlock the dimensions that define its position and then i lock the dimension in the new position; the window seems to be ok but only in the RFA file. When i imported it in my project file, the windows moves in the wrong way in my real wall.
View 4 Replies View RelatedI am doing a five stories building and when ad the structural column with concrete cast in place material, the representation in plan view does not cover the block hatch of the wall. See attached image. I have read all about structural columns and did not find any solution.
View 5 Replies View RelatedI have a problem inserting the slanted columns when I use the "Beam/Column joints" commando. When I insert the slanted column, the beams are divided.
It should look like picture 1, but it always ends up as image 2. How can I solve this?
I'm trying to align a nested family to a reference line in my host family so that it rotates around a certain point.
I've created the reference line in my host family, locked the end point to two reference planes and then gave an angular parameter to the angle between the ref. line and the ref. plane.
I then inserted the nested family and aligned it to the ref. line. The problem is that when I flex the angle, i get a "Constraints not satisfied" error..
What could be wrong?
I'm using a generic face based family for both host and nested families...
Using Building Design Suite Ultimate 2014
I am trying to give an Expression like sqrt({Jx}/{Section}) in column properties in family table editor. but its not working.
Find the attached image .....
Inventor Professional Suite 2010
Windows 7
Any way to get a wall sweep that's set up in the type/structure properties to follow a wall if that walls profile has changed. For example, in the image below, I've split the wall and adjusted it's profile to create some cheesy angled parapet. How do i get my wall cap to follow along? I thought splitting it and changing it's height would work, but no. And if I change the profile without splitting the wall the wall cap just runs right through the wall, as if the profiel was never even changed.
View 3 Replies View RelatedI am trying to align the curtain wall with the edge of the concrete slab/face of wood framed wall (Core). I have tried to align and move however the whole wall moves as well as the edge of the slab. How I can move the Curtain wall leaving the other elements in place?
View 2 Replies View RelatedRefer to the attached file. How can I cut the RED part of the Wall 1 (W1) , where Wall 2 is sloped. I also want to cut a hole in wall 2 (W2) by the BLUE rectangle , but why I can't do that .
I also want to add a second floor to my project but I can only see the" Level" icon goes grey and I can't click it.
When I try to change the length of a wall it grows at both end. How to grow at one end only?
When I change the wall type to one with a different thickness, I cannot control which face of the wall remains fixed and which face moves. eg: change from 130mm to 250mm screws up my room width. How do I do this?
I am trying to make a floorplan of my house in Revit 2013, but I am having an issue when it comes to one wall in my house. I have an opening in the Master Bedroom that leads to the bathroom. This wall has a weird arched-like opening in it and I have no clue how to make this in Revit. I have attached a sketch.
Also, my exterior walls are 7' tall but the interior walls start at 7' and go up to 8' once in the middle of the house and reduce back to 7". How does one set that up in Revit?
EDIT: May have made the image too small to see, but the top is not arched, it is actually half of a decagon.
I have a question about wall profiles. I want to make a profile on a wall so I can make Zinc Panels on the wall that are 10" X 20". I've attached a picture of what I'm going for. I'd like it to have a 1/2" spacing between them and with a joint depth of 1" and I'd like to do this is the wall type so that I can use this wall in multiple places rather than having it model-in-place. Anyway I have made a profile that is 1" X 10" so that it can become my panel profile. But when I go to add it to the wall as a wall sweep as I have seen people do I get hung up on how to make it tile up the wall and also I don't understand how to make the profile so that it is 20" wide. I have a screen shot of where I'm editing this too. Below is the link of the site.
View 8 Replies View Related“Drag wall end” to the edge of the wall (indicated),In the attached screenshot, I wanted to drag the end of the temporary dimension from its location to the end edge of the wall but sounds not to respond!
How this temporary dimension can be dragged to the edge of the wall?
I have two roofs that I am trying to join. It consists of two Gables. The eaves and type of cuts are the same, but it still says they can't be joined. Attached is an example of what is happening. The shown highlighted image is actually what I am trying to achieve.
View 4 Replies View RelatedWhen working with mullions, there is a "Toggle mullion join" at the end of each mullion and you have to pick each one individually to toggle. Is there any way to pick a group of mullions and have them all toggle at once?
View 2 Replies View RelatedI have this house Im trying to make on Revive and I can't get the roof to join together at all. I've had this problem for awhile now and I can't seem to get past it.
View 7 Replies View RelatedNot sure this is possible. I'm modeling a box gutter using sweeps, is there any way I can join the 2x sweep?
View 1 Replies View Related
