I have a small problem, trying to print from R 2013 some pdf's of a long section of a building...aprox 30 m.With a scale of 1 to 20 ,,,the pdf just looks bad and unclear when you get to zoom a little bit in it.What am I doing wrong,although I use settings like highg quality pdf and so on.
View 1 Replies
i am wanting to do is enlarge a gif or jpg to about 4 feet tall and print it.
i have seen this done were it breaks up the pic into sections and prints each section as a different page that you cut and paste together,
We just upgraded a project from 2012 to 2013. After upgrading, there are two floors which do not show up as cut in any sections (they displayed correctly in 2012). The two floors in question appear in the section, but not as cut elements (no cut pattern) and it is showing edges of the floor that should be well behind where the section is cut. One floor is 8" concrete and has been made to slope using the modify sub elements command. The other floor is a variable thickness floor modified in the same way to be the earth below the concrete floor since the topo is not nimble enough to follow the shape of the concrete floor.
I tried remodelling the floors. No luck.
I can model it in a separate file, cut sections in that file and have it display correctly. If I insert or paste that into the main model, it goes back to displaying incorrectly.
Our structural engineer had copied the lake floor into their model which is linked into ours, so I deleted the lake floors in the structural model, reloaded it and then remodeled the floors again. And it worked... in only one of the dozens of sections that show the lake floors! So that's one more than before...
In one of the attached images you can see the sloping lake floor and the earth floor below it as it should appear and in the other image you see them both in elevation rather than section. The 3d image shows the lake floor and the surrounding "earth floors". The center of the lake floor is 7'-0" below the outermost perimeter of the floor.
I have a structural model linked into my architectural and I cannot seem to cut the link in sections. All I can see is the 'elevation' of the link whilst my architectural cuts. I have the link set as by host view and the view extents correct.
View 4 Replies View RelatedWhen i attempt to plot some layouts to adobe pdf, they are coming out with sections that are blank. They are scattered around the drawing but the drawing content is missing. when i use the built in pdf creator, it is shifting some things around to where they don't belong and i can't have that!
View 1 Replies View RelatedI am photographing and cataloging the paintings and drawings of an artist. There are over 3,000 of them. LR is such a good database that I am hoping I can use just that and add the details into the IPTC data - Title, Medium, Date created, Size, Price, whether sold and to whom, and - crucially - which shelf in the artist's store building they are located.
My idea was to use SlideShow Pro to publish the catalog to the web for dealers to browse, and my experiments show this would work very well, with IPTC data available on mouse-over.
I also need to produce a catalog with images and info for the artist's assistant so that she could quickly locate a requested painting on the correct shelf. Again this seems feasible up to a point as it is possible to print out the photos with IPTC information.
BUT - and here is my problem: I do not want all the info that the artist's assistant needs in the catalog to be available on the public slideshow, so have put different bits of info into different IPTC sections. But then I come across the limitation of printing in LR - only one section of IPTC info is allowed.
As it is I am at the moment also entering the info into a database (File maker Pro). I find on a good day with the wind behind me I can crop and adjust and catalog about 30 paintings an hour in LR. Also adding the info to File maker nearly doubles that. And more importantly it will be clunky and prone to error to have to alter or add to two separate databases in the future.
was setting up my printing sheets when i noticed my south and west elevations are showing up as sections. how to change back to elevation views.
View 3 Replies View RelatedI am laying out a simple structure. Bearing wall to bearing wall is 35’, with a few non bearing walls between the bearing walls. I will be using a truss to span from bearing wall to bearing wall. What would be the best work flow for the drywall ceiling material. The ceiling seems to require a core element. I cannot seem to manage drywall alone. If I create a ceiling with 2x4 core and drywall finish and create a ceiling over the whole area the ceiling seems to auto dim to the ceiling finish and not the core 2x4. Then there is the issue of the clean up at the top plate were the wall and ceiling finishes meet
View 1 Replies View RelatedIn Revit sections, we can add split segment in plan.
How can we show the Horizontal sections in sectional view and how can we split the horizontal section such that the drop is vertical.
I know that one workaround to show vertical drop is to use plan region on the Horizontal Plan View. But is there a better way? If not is autodesk looking forward to incorporate this in further releases?
I want to create sections and plans showing interior finishes. As walls are all of the same structure I used the split face tool. When applying 'paint' to the face it only gives me the options of materials not fill patterns i.e. hatches. How do I get it to apply hatches or is there a visibility setting that i need to change.
View 1 Replies View RelatedWhen I edit a note on a material tag on a wall section it changes multiple tags. For instance I have a wall section with insulation in it and have placed detail components (2x4's) as top and tie plates. When I tag the insulation it shows a question mark, I edit the question mark to the desired insulation note no problems. However when I go to tag the top and tie plates they come in with the same note as the insulation. When I edit the note for the top plate it changes the insulation as well. How do I keep this from happening?
View 1 Replies View RelatedWe have an issue here where a user has N/S/E/W elevations of a building or radial type layout. Then there are sections derived from these elevations. If you open up the section pointing north and south you can place radial dimensions on the view needed. If you go into the section pointing east/west you cannot. It starts the command, just doesn't allow you to pick anything. I will post a sample file in a sec.
View 9 Replies View RelatedIn sections the scale of the hatch appears very large. Attempting to change the scale via /properties/ material/ cut pattern/ fill pattern/ edit/ import/ change scale/... has no effect!
View 2 Replies View RelatedHow can i draw column like this >>
View 1 Replies View RelatedI just download my Revit 2012 and the Project Browser does not show options for Elevations and Sections.It only shows Floor Plan and Ceiling Plans.When trying to bring Windows or Door, it says it is not loaded. It asking if I want load it. Well! The next step has 20 something options but nothing to do with Windows or Doors. How to get out of this Nightmare?
View 9 Replies View RelatedThere is a way of controlling how much some objetcs extend outside the scope box? The levels, sections and grids extend too much to my taste and the space avaliable in my sheet.
View 1 Replies View RelatedI want to print to a pdf file. On the export files it list dwf and dwfx, but where is the export to pdf?
View 1 Replies View RelatedWhen attempting to print to PDF a view from Revit, I am running into an interesting problem: in preview, the image displays properly, but when the file generates, it is blank, with the exception of black lines on each side of the page.
View 1 Replies View RelatedI have a free program called PDF factory that lets me "print" to a PDF format to scale and works great. Except I tried to do it with a "shaded" building with sheet metal on as the walls, so evenly spaced vertical lines as the patter. The walls look perfect on the elevation views and the 3D view. but when I try to save the "print" to the PDF view the lines are not evenly spaced and there are not many of them. Is there a better way to export to a PDF? It says when I "print" to my PDF format that Revit will use Raster, could this be causing the problem? If so, how so I use vector?
View 1 Replies View RelatedHow do I print a PDf from Revit 2013?
View 1 Replies View RelatedWe usually print our sheets to PDF from REVIT. However, whenever a sheet has a 3D view with shade and shadow the PDF file has what appears to be a bunch of rasterized tiled boxes. Of which the borders of these boxes show up through the 3D image.
View 3 Replies View RelatedI know that some objects can be turned off from printing but is it possible to create a line style that will not print?
View 4 Replies View RelatedUsed to plot, but now it doesn't. The VG title block is checked.
View 1 Replies View RelatedI have made crop region lines to be heavy lines on elevations and it shows heavy lines on my monitor . When I created PDF file or print preview, it does not show any heavy lines of crop region lines.
View 1 Replies View RelatedI'm having issues with print quality on certain drawings, which is a shame as print quality generally exceeds that of AutoCAD Architecture.
The issue I have is with a SHADED and shadowed elevation drawing. When I go to print to PDF it insists line removal is done using raster rather than vector processing. This leads to a poor quality PDF both on screen and printed.
I accept that automatically generated shadows may make this necessary but with then turned off, I don't.
If I print a coloured plan, say a room or area drawing with automatically generated colours, it's quite happy to plot it using vector processing. I DO NOT see any difference between this and a shaded elevation without shadows! Any way of improving the look of raster processed output?
We have several users utilizing the same printer. To prevent sheets from different jobs from mixing, and a large quantity of pages sitting in the printer, each print job is queued in the printer until the sender requests that it be printed at the printer. With Revit, the problem is that each sheet is sent as a separate print job, meaning that a 300 sheet print jobe requires me to stand at the printer and request that each one be printed (300 requests). In AutoCAD, the PUBLISHCOLLATE variable sends all sheets in a publish operation as a single job. Is there a way to do this in Revit 2011?
View 2 Replies View RelatedI am trying to print from revit 2013 and every time I try and to print a sheet, view, or anything the program crashes saying "unrecoverable error". I have tried updating the software, reinstalling the software, and the error still continues.
View 3 Replies View RelatedWe have experienced this problem with multiple versions of Revit. When we plot to PDF (bluebeam driver), it will sometimes not create the final sheet that was checked in the list of sheets to print in the print dialog box.
View 3 Replies View RelatedIs there a way to print an area larger than my titleblock, so that I can include the border defining the edge of the paper in the final printed pdf?
My workflow requires me to open the pdf in illustrator and make adjustments before a final print. I need the boundary printed so that I can scale the drawing inside illustrator back up to proper size.
Maybe I need to make a custom titleblock with a larger boundary?
I have been trying to set up macros which stop lines from printing for our company title block, I have been using and following this website Making Lines Not Print (with Events) | Boost Your BIM - making Revit even better. It keeps coming up with errors and therefore I can't run it.
View 4 Replies View RelatedI am going out to see a client tomorrow and wondered if any of you have came across a problem like this before??
They are inserting images, mainly their logo and all looks fine untill they print...
When printing the images are all mirrored and flipped? I have tried it in my office and all prints fine.. Obviously this points to his printer but I am not so sure....
