Revit :: How To Handle Worksets / Design Options And Phases
Apr 26, 2010
These are three separate question :
1. When I link A revit model (having different worksets) into B revit model, We can control the worksets visibility at the time of linking. We can select any workset to be switched off and it will not be visibility in any view. Can we controll it after linking and on the basis of views, i.e. Can we switch off any single worksets of a link file in a particular view. My understanding is that We can't control worksets of a link file in our main revit model.
2. If A.rvt contains deisgn options. can we link those design options to design options in B.rvt, Can we set the visibility of a view in B.rvt to see desired design option from A.rvt. My understanding is that revit link does not contains design options information.
3. Similar rules applies with Phases. We can't link phases from A.rvt with phases in B.rvt, Also can not controll the visibility of phases of a linked revit model.Seeks experts comments to confirm my belief. What are the nearest possible work around for these issues.
View 9 Replies
ADVERTISEMENT
Nov 14, 2013
I have four floor plans of varying differences on the same level that have been set up in different views, and organized by 'Design Options'. It would be very beneficial to be able to overlay these plans (eg. to see the differences, to make relative manipulations) as one can with the 'Underlay' feature can with different levels.
I have thought about placing the views on the same sheet and then activating the view I want to revise, but there is transparency complications . Suggest an alternative for a Design Option Underlay ability?
/still holding out for the ability to organize the listing of 'Design Options'
View 2 Replies
View Related
Nov 6, 2011
I have a tenant improvement project: two side by side medical offices. The owners want to run a joined practice and are building it together, so I'm preparing one set of construction drawings. However for a permit drawings I have to prepare 2 sets of drawings with each office separately-what's the best way of doing it? Also how should I handle sheets?-should I create 2 series: permit and CD? I'm not sure how to do it.
View 2 Replies
View Related
Feb 9, 2012
Is there a way to organize Design Options (alpha numeric) once they have been created.
I work for a large home builder and we will have multiple elevations for each floor plan. The elevations are usually labeled A, B, C, D etc. If an elevation changes labels, say elevation D becomes elevation B, the order will now be A, D, C, B; they cant be reordered into alphabetical order. Which can become confusing. Make sense? Attached is an example of a basic Design Option from one of my houses. In a typical house we can have 50-60 design options, that can change names over years, and they need to remain in an easily read and sourced order.
View 2 Replies
View Related
Sep 7, 2012
I am trying to move multiple elements from one workset to another.
Everyone on my team have synchronized and closed their file. I have made all worksets editable.However, I am still unable to change the workset.
View 3 Replies
View Related
Aug 10, 2012
I am using Revit Architecture 2013 and I have a few different design options for the mian level of a house I am working on. I have the North wall of the house in a design option for the living room at the moment. But I have decided I no longer want that wall in the my living room option, I would like to move it to my kitchen design option so I am able to move a window that is located on that wall. I cannot seem to find a way to move a wall from one design option to another or have it in both if it is already part of a design option. How I can get this wall and the windows located on it into my kitchen design layout without having things being double counted in the schedules?
View 6 Replies
View Related
Mar 14, 2013
'm trying to create a new sheet , currently using design options, the create new sheet option is grayed out.
View 1 Replies
View Related
Aug 26, 2011
I have several architectural models linked into my central file on a project. For this project, there is an addition to the building that is a design option. When I look at the linked files, though, I can only see the existing construction. I also know how to copy/monitor levels, but I want to view the architect's room elevations in my model. How can I copy the architect's design options and specific views into my model?
View 1 Replies
View Related
Aug 19, 2011
I am doing several houses with design options, but we need all the information for the main model will be unique for all the options in every model in order to keep only one file and manage the information just like and xref.
View 4 Replies
View Related
Feb 10, 2012
I want to know if is it possible to create design options in a grouped project.
View 3 Replies
View Related
Jun 21, 2012
Baffing issue for us:
We have a "core & shell" model linked into a "fit-out" model. We are working with design options in the "fit-out" model with different design options.
1. In a 3D axo view and working in the main model, we can see the linked "core & shell" file.
2. In the same 3D axo view and working in the primary design option, we can see the linked "core & shell" file.
3. In the same 3D axo view and working in any of the other design option, we CANNOT see the linked "core & shell" file.
The visibility & graphics settings have not been changed. The worksets settings have not been changed. We have been unable to overcome this issue. We are simply flippiing between different design options and the linked model disappears.
View 2 Replies
View Related
Jan 31, 2012
Is it possible to copy a phase from one level to the other. For example, on Level 1 I have walls that are Existing, Demo, and New Construction.
If I select the objects and copy to clipboard and paste the objects to another level they will all switch to New Construction. Is there any way we can have the walls remain the same phase when copied to another level?
View 1 Replies
View Related
Oct 24, 2013
The issue is cutting an opening in an existing floor so that in only shows in a new phase.I have created a floor based generic family with an opening tool and added an edge liner as a sweep. It hosts onto the floor and cuts it OK (in section and 3D). BUT in plan view objects below dont show through - see blue dashed on the screen clip. You will see that the red dotted opening>vertical cut show the stair below OK. Have a go (floor opening lined.rfa) and tell me why the opening is opaque!
View 2 Replies
View Related
Apr 4, 2012
I have a project that has been completed in Revit. The designed facility needs to be split into two phases due to budget constraints. I have looked at creating two Phases - Phase I and Phase II. However the tricky part is having Phase II display greyscaled. Successful in having phase I greyescaled and displayed acordingly with Phase II. I have looked at the phase filters, but unsucessful in getting phase II to be greyscale since it is future work in the order of the phases.
View 6 Replies
View Related
Apr 3, 2013
I have a multi-story model with "Existing" and "New Construction" phases present on each level. The graphic overrides are functioning properly on the 1st Floor (existing is displayed in lighter line weight and half-tone) but for some reason the overrides are not applying to the 2nd Floor.
View 1 Replies
View Related
Nov 9, 2010
I have multiple building pads in a model because I have multiple phases to represent. The problem I'm having is that the pads are cutting the topo surface in all phases. When I check the properties for each pads they all appear to bel properly identified as being created in the appropriate phase and yet there doesn't seem to be any way to turn off the building pad for future work in the existing conditions. See attached image.
I suppose the other possibility is that the pads are not really in the views, but the topo, having been excavated in one view,stays excavated in all views and won't fill in?
how to disable the pads where and when they're not needed? I've tried hiding the pad elements in the views, but that doesn't seem to do anything.
View 9 Replies
View Related
May 4, 2013
One of the common processes we have to do is to transilate file formats into a type we can use. Most the time it is for use in AutoCAD MEP...
Is there a good one-stop place to get info on import export options from / to softwares included in Autodesk Building Design Suite Ultimate?
View 1 Replies
View Related
Apr 20, 2006
Create an action that would reduce the dimensions of images in a folder. Then, save the reduced images for the web (Save for Web), then close the orignal image without saving it.
I believe I created the action properly, but when I use the batch command, things go horribly wrong. The first image in the folder, the one I open when recording the action, keeps getting reduced, and the other images never open.
View 3 Replies
View Related
Apr 22, 2013
I've been looking for a site / tutorial that outlines a detailed workflow for exporting a model from Revit and into 3ds Max for rendering and animation.
I'm particularly interested in how best to set a model up in revit to make this process less painful - particularly around material assignments, mapping etc. so that I can switch from the multi-material (using material IDs) setup that comes into Max over to the Architectural & Design materials.
View 3 Replies
View Related
Sep 16, 2011
Is it my inexperience with the product or is Revit Architecture far less competent for designing residential architecture than it is for commercial? I'm trying to design a large home and face workaround after workaround - many of which defeat the BIM materials inventory database I'd like to develop for quoteing the job. I understand that a Wood Framing Extension is available, but I'm still a student learning the software and the application is a subscription item and a high cost.
View 4 Replies
View Related
Jan 18, 2014
The problem that I am facing at the moment is the lines are showing through my design. I have tried making the lines invisible but I cant because if I do than the place where I need the lines to show will not.
View 1 Replies
View Related
Nov 2, 2011
I would like to know what is the best way to design a form of facade, similliar to the picture of the building I have uploaded and mentioned in the title of this post? Take note that I still am relatively unexperienced with the program
View 3 Replies
View Related
Dec 10, 2013
I have run in to problem with Design Option. When I try to change the primary option I get a error message, see picture below or picture attached.It says "Elements can't be duplicated".
View 1 Replies
View Related
Feb 17, 2011
I am currently trying to export models into dwfx format for design review and freewheel. However, I have a problem opening the dwfx files that are 16,000 kb in size or higher. How to make the file smaller in Revit.
View 2 Replies
View Related
Oct 18, 2012
I am using Revit Architecture 2013 and am trying to create a window family that has different grid options built into the family. I have included a copy of one of my window families I am working on and an image for an examples of what happens when I load all my windows into a project and place them. Some of the grid families do not automatically adjust to the size it should be. But if I click on the window (lets say it as no grids) and then select the no grid parameter again then it will adjust. How I can get these windows to adjust automatically so I don't need to do an extra step to make them look right!?
View 3 Replies
View Related
Apr 3, 2013
I am trying to design the border mullion of the curtain wall, in a way that its centerline aligns to the border gridline.
For default the border mullion aligns the external face of it to the gridline, but I would like it to act as the internal mulluon - aligning with the centerline.
View 4 Replies
View Related
Aug 23, 2012
I'm a model, I need to design a model for window curtains and bed with my blanket.
For example, I took the picture.
View 2 Replies
View Related
Feb 16, 2013
I'm trying to export Revit into Navisworks Simulate but there's no Navisworks tool in External tools. I did a full install of the Design Suite and checked Control Panel/ Programs/ Programs and Features for " autodesk navisworks simulate 2013 exporter plugins" but they're not installed. Are the plugins included in the Suite or do I download them from Autodesk?
View 2 Replies
View Related
Dec 11, 2013
In revit 2013, How do I control the Control File Save Options Settings globally. For example I want all files to save only one back-up file.
View 4 Replies
View Related
Dec 5, 2011
I just download my Revit 2012 and the Project Browser does not show options for Elevations and Sections.It only shows Floor Plan and Ceiling Plans.When trying to bring Windows or Door, it says it is not loaded. It asking if I want load it. Well! The next step has 20 something options but nothing to do with Windows or Doors. How to get out of this Nightmare?
View 9 Replies
View Related
May 2, 2013
I'm attempting to delete a design option that we created in order to alleviate model creation conflicts. We were testing whether it was to be a sub-category design option or a main heading, so I just modeled a couple things (in a floor plan that was created months ago in another design option) to try and get them to show up. When I realized that sub-category was not the way to go, I tried to delete that design option and it removed the floor plan I was using.
I examined the "Visible in Option" line and it has the name of an option that I'm not deleting, so....? Now what? I just want to clean up my model and remove that test design option.
View 2 Replies
View Related
