Revit :: Deleting Design Option Deletes Plan View
May 2, 2013
I'm attempting to delete a design option that we created in order to alleviate model creation conflicts. We were testing whether it was to be a sub-category design option or a main heading, so I just modeled a couple things (in a floor plan that was created months ago in another design option) to try and get them to show up. When I realized that sub-category was not the way to go, I tried to delete that design option and it removed the floor plan I was using.
I examined the "Visible in Option" line and it has the name of an option that I'm not deleting, so....? Now what? I just want to clean up my model and remove that test design option.
View 2 Replies
ADVERTISEMENT
May 30, 2012
I am working in a project where I need to represent the reflecting ceiling edges in the plan view. I put the first floor plan as underlay, and selected the RCP projection but I don't see the dropped ceiling lines to select them with the linework command. I have done every thing possible with the view range but I don't see the lines.
View 7 Replies
View Related
Jan 10, 2012
We have our first project in Revit that we are having to split among multiple sheets because of the size of the building, so I have made 3 dependent views from the main overall view, named them, cropped them and placed each part (A,B, and C) on separate sheets. Now that I am trying to do enlarged toilet plan views, I want to tag the plans with the plan callouts on the 1/8” sheets that are the dependent views, but all the view tags are referencing dependent view A since it is the first dependent view in the list. If I change sheet A to be named Sheet X for instance, all the view tags now reference sheet B since that becomes the first dependent view alphabetically. I want them to reference the sheet they appear in, but I can’t seem to figure out how to do that, even though they are in different dependent views completely and within the crop region, they all default to the first dependent view in alphabetical order.
View 4 Replies
View Related
Dec 10, 2013
I have run in to problem with Design Option. When I try to change the primary option I get a error message, see picture below or picture attached.It says "Elements can't be duplicated".
View 1 Replies
View Related
Dec 23, 2013
I was following a tutorial when he created a structural plan where he'd place his footings. when i tried it on my Revit Architecture 2014, i found out that i didn't have that feature. is there any way i can turn it on?
i'm not sure if he's using revit architecture because he just refers to it as Revit 2014. i made a floor plan below the 0 mark but things will be tidier if i could make structural plan views.
View 2 Replies
View Related
Jul 15, 2011
If i draw a beam in plan view en define the height, the beam disepare. Is there a posibility that the beam is in place and you can see a dash dot line and two dashed lines in plan view?
View 1 Replies
View Related
Mar 6, 2013
Currently I have created Rooms and a Legend such that I have a coloured Plan View by Room department.
The colour boundaries extend to the centre line of the defining Walls. Is there a way to get the coloured zones to follow the Room boundaries?
I realise I can overwrite the Wall pattern and use a Solid pattern to hide the colour - but this is not what I want ...
View 2 Replies
View Related
Jan 17, 2013
I'm currently looking into switching from Vectorworks to Revit due to a job application I'm being offered. What I really want to know is if the following floor plan is possible to make in Revit. I just want floor plans to be with color to better show the different things on it and make them more clear.
I also want to know if it is possible to show symbols in a plan view other than just a rendered hidden line view of the 3D part of it, so I can have a simplified version for the plan view and a detailed object for the 3D. Like you have a 2D-plan component for the plan views and e 3D component for all other views.
View 5 Replies
View Related
Nov 22, 2012
I need to create a wall the has a profile (in plan view).
View 1 Replies
View Related
Feb 24, 2014
How do I raise the cut plane in the floor plan view. I have windows that are not showing up in the floor plan because the sill is above the cut plane.
View 1 Replies
View Related
Aug 23, 2011
I am already using autocad and Covadis (because I'm road-design, etc. ...-); I'm new building and I use Revit Architecture 2011
Already I do not understand why my isolated foundations are not visible in plan view when the footings are beautiful and well visible in the plan view,...
View 1 Replies
View Related
May 15, 2012
I've got some troubles creating a proper ceiling plan. What goes wrong (imo) is that my wall sweep is shown on my ceiling plan while it shouldn't.First image shows the ceiling plan. (on image 3 you will see the wall sweep I mentioned in red).
This image shows the view range used.This images shows the section (right), 3d (top left) and ceiling plan (bottom left) highlighted the wall sweep.Why / how do I prevent this wall sweep from showing up?
View 9 Replies
View Related
Nov 28, 2011
Is it possible to add a color region to a family in plan view? I need to add a color region to the plan view of a single flush door family for training purposes (several co-workers see color filled areas better than black and white single lines with the projector we have). I would like to add a color region to the door and frame in plan view of the door family.
View 1 Replies
View Related
Aug 20, 2013
How do you make a wall that's not rectanglar (in plan view)?
See attached image.
The brown color at the end of the wall indicates the polygonal shape which should be part of the wall.
View 2 Replies
View Related
May 11, 2010
Explain the logic behind the differences between RVT Categories and how they display in Plan View?
Example:
I made a custom component (Family) that was set as the 'Generic Model'
Category.
When placed, its elevation was set above the Cut Plane but below the Top of the Primary View Range for the Plan View. The Object displayed in its entirety. I then decided that this component was really better categorized as
'Specialty Equipment'. So, I re-assigned it in the Family Editor, and re-loaded it into my Project. As I did this, the object disappeared from Plan View. I then switched to a 3D View to verify it was still present in the model - and it was.
So why does Generic Model Display, and not Specialty Equipment, I ask? I've discovered that if I lower the Elevation of the Specialty Equipment to exist at or below the Cut Plane, but above the Bottom of the Primary View Range; it will display in Plan View. I've also tested and discovered that adding Symbolic Lines to the Plan View of the Specialty Equipment in the Family Editor and re-loading into the Project will not overcome this issue of elevation - if the object is above the Cut Plane the Symbolic lines will not display either.
I note that Specialty Equipment does not have a "Cut" setting for Lineweights in Object Styles, and Generic Model does. Is this the indicator for this display behavior that I'm experiencing? And if so, why is 'Specialty Equipment' regulated to this type of Category? Why not have a 'Cut' setting for it?
Quite a fair bit of an Architectural model gets lumped into this Category:
lockers, toilet accessories, kitchen equipment, medical equipment, etc.
View 6 Replies
View Related
Jun 7, 2012
i want to create a schedule that will show which views are visible within a Revit 2012-2013 plan view. Any way to do this or a work around?
View 7 Replies
View Related
Oct 11, 2013
I accidently deleted a section marker from a plan view. The section still exists and in shown in other plan views. I feel stupid for asking, but how can I get the section marker to reappear on the original plan view?
Infrastructure Design Suite Premium 2014
Self-built i7-3930K, 16Gb RAM, P9X79 m/board
SSD(system), HDD(data), Win7Pro64, Quadro K4000
View 3 Replies
View Related
Oct 26, 2013
bring back my site plan view!, and the ability to use shadow and realistic material!because when did another site view i am unable to use shadow and realistic view!
View 1 Replies
View Related
Mar 2, 2012
How do I turn on/off wall elements in my plan view? I'd like just the core structure to show for dimensioning purposes and turn off the sheathing etc.
View 6 Replies
View Related
Jun 1, 2012
Its a stair with parts below the view level shaded black and above parts shaded as material settings. What controls the "beyond - below" shading?
View 3 Replies
View Related
Oct 30, 2012
Is there a way to change the level that a floor plan view is associated to?
View 4 Replies
View Related
Oct 22, 2013
I have created a "Jersey Barrier" as an adaptive component (attached). It is basically a profile extruded along a series of reference lines hooked to adaptive points.
In some plan views, under certain geometric configurations, the extrusion disappears in the view. The points highlight if you mouse over them. In a parallel 3D view, the component is still there. If I adjust the geometry in certain ways, the component will reappear in the plan view.
Here is an isolated view (3D on left, plan on right) with a configuration where the object does not appear in plan.here's a view where I have moved one of the adaptive points, and it appears in plan.
View 3 Replies
View Related
Nov 18, 2013
by default. I forget what but there's some routine to make this family cut properly in a plan view. Why they made viewing the top of the family the default position I DON"T KNOW but what do you expect from programmers?
AutoCAD 2010
AutoCAD LT 2013
Revit Architecture LT 2013
View 7 Replies
View Related
Oct 30, 2013
I created few families then loaded into project when i placed them all one of the type was not visible in Level view.
View 2 Replies
View Related
Aug 6, 2012
In floor plan view how do I make a wall have a concrete texture inside instead of the default (criss cross)?
View 9 Replies
View Related
Apr 23, 2012
I use all the time L shape and U shape winder stairs in combination with the Monolithic Type.
We use to concrete the monolithic part of the stairs and then dress the stairs with treads and risers. The new tool looks that working very nice.
So OK I draw the U shape winder stair and of course i want to construct the stairs.
I want to prepape a detail plan view with dimensions only for the Monolithic Part (Concrete) of the stair but i can't find a way to dispay only the monolithic part without Treads and Riser.It is possible in 3d view but no in plan view. The news tool that calculate winder stairs is "half job done" if i can't print with dimension the concrete part of the winder stairs.
View 7 Replies
View Related
Nov 4, 2013
The Cut Plane in a Plan View doesn't really represent the cut component but instead some kind of projection.In my case, I use a lot of Face Based Windows and Doors since my walls are often slanted. The Plan View representation of these components doesn't look right. A workaround is placing these components in a Component/Model in Place environment.
View 3 Replies
View Related
Mar 2, 2012
How can i get Floor plan etc to drafting view whitout export to Auto cad and back to revit 2012?? Or freeze a Floor plan will be okay.
View 2 Replies
View Related
Jan 3, 2012
I would like to place a parameter in the title block to indicate the view in the plan layout.
View 1 Replies
View Related
Feb 23, 2012
Is it possible to create a non-plottable line style that is only visible in a plan view? I want to use something other than the invisible line.
View 3 Replies
View Related
Apr 24, 2012
I'm trying to find a way of filtering the 'work in progress' section visibilities from a plan by view filters. The filter I use is 'Sheet Name' equal '<None>'. Then turning off visibility. It works when used in the Browser organisation filters but not in the view filter for the sheets.
I don't want to create a check box or dialogue box for the sheet as this will add to the required maintenance.
View 1 Replies
View Related
