Revit :: Isolated Foundation Not Visible In Plan View
Aug 23, 2011
I am already using autocad and Covadis (because I'm road-design, etc. ...-); I'm new building and I use Revit Architecture 2011
Already I do not understand why my isolated foundations are not visible in plan view when the footings are beautiful and well visible in the plan view,...
I am having issues with isolated foundations not showing as cut when the cut plan is through the foundation. The wall foundations are shown cut, but I cannot get the isolated foundations to show cut. I verified by wall sections that both foundation types are definitely passing through the cut plane.
I'm having problems seeing the walls I drew at the foundation level in this project. The walls should be shown but I can't get to see them except in a 3d view. Also, when i intended to draw them, I think I should have done it from the foundation level plan but I could not set the plan view to see the above objects in order to draw from them. I drew it from another level and then I modified their base and top constraints afterwards..
I tried to modify the view range of the foundation level without success.
I am having trouble placing a wall foundation under a curtain wall in my project. Revit says that a foundation has been added but it is not visible in any view. I've tried editing the visiblity properties but that didn't fix the probelm.
i draw up all of my walls, i connect them properly, cleanup etc. then i want to trim them with my roof slabs and what i see? i see my walls suddenly dissappear in 3d view but are still correctly shown on plan view? i know it has something to do with roofline because when i tried to project them automatically to ontu my roof slabs the walls dissappeared too!
I am working in a project where I need to represent the reflecting ceiling edges in the plan view. I put the first floor plan as underlay, and selected the RCP projection but I don't see the dropped ceiling lines to select them with the linework command. I have done every thing possible with the view range but I don't see the lines.
Autocad Architecture 2012: my dwg is fully visible in 3D View but partially visible in plan View. What could be causing this problem? See screen shot attached.
I have a model done and cutting a Foundation plan and then dressing it out. I want to use the architectural dimensions but needing to offset the column bubble at the stair pad as you can see on the attached dwg. I cannot figure out how to adjust the dimensions with out having to manually draw a dim line.
I drew a structural wall with the 'rectangle' function, but this error appears and the wall is not visible in the floor plan 'level 1' ?
"Warning: None of the created elements are visible in Floor Plan: Level 1 View. You may want to check the active view, its Parameters, and Visibility settings, as well as any Plan Regions and their settings."
I am trying to place a receptacle on a wall and I keep getting this message "None of the created elements are visible in Floor Plan: Basement Demo. Plan - Electrical View. You may want to check the active view, its Parameters, and Visibility settings, as well as any Plan Regions and their settings." I have everything turned on in my visibility graphics.
Am getting warning "None of the created elements are visible in Floor Plan: 00 GF View. You may want to check the active view, its Parameters, and Visibility settings, as well as any Plan Regions and their settings". Phase settings are correct, no hidden elements etc. Cannot add anything by create similar, build panel. Its Revit 2013 - I have been getting a lot of cannot continue crashes but is this a forthcoming fix issue?
We have our first project in Revit that we are having to split among multiple sheets because of the size of the building, so I have made 3 dependent views from the main overall view, named them, cropped them and placed each part (A,B, and C) on separate sheets. Now that I am trying to do enlarged toilet plan views, I want to tag the plans with the plan callouts on the 1/8” sheets that are the dependent views, but all the view tags are referencing dependent view A since it is the first dependent view in the list. If I change sheet A to be named Sheet X for instance, all the view tags now reference sheet B since that becomes the first dependent view alphabetically. I want them to reference the sheet they appear in, but I can’t seem to figure out how to do that, even though they are in different dependent views completely and within the crop region, they all default to the first dependent view in alphabetical order.
I was following a tutorial when he created a structural plan where he'd place his footings. when i tried it on my Revit Architecture 2014, i found out that i didn't have that feature. is there any way i can turn it on?
i'm not sure if he's using revit architecture because he just refers to it as Revit 2014. i made a floor plan below the 0 mark but things will be tidier if i could make structural plan views.
If i draw a beam in plan view en define the height, the beam disepare. Is there a posibility that the beam is in place and you can see a dash dot line and two dashed lines in plan view?
I'm currently looking into switching from Vectorworks to Revit due to a job application I'm being offered. What I really want to know is if the following floor plan is possible to make in Revit. I just want floor plans to be with color to better show the different things on it and make them more clear.
I also want to know if it is possible to show symbols in a plan view other than just a rendered hidden line view of the 3D part of it, so I can have a simplified version for the plan view and a detailed object for the 3D. Like you have a 2D-plan component for the plan views and e 3D component for all other views.
I've got some troubles creating a proper ceiling plan. What goes wrong (imo) is that my wall sweep is shown on my ceiling plan while it shouldn't.First image shows the ceiling plan. (on image 3 you will see the wall sweep I mentioned in red).
This image shows the view range used.This images shows the section (right), 3d (top left) and ceiling plan (bottom left) highlighted the wall sweep.Why / how do I prevent this wall sweep from showing up?
Is it possible to add a color region to a family in plan view? I need to add a color region to the plan view of a single flush door family for training purposes (several co-workers see color filled areas better than black and white single lines with the projector we have). I would like to add a color region to the door and frame in plan view of the door family.
Explain the logic behind the differences between RVT Categories and how they display in Plan View?
Example:
I made a custom component (Family) that was set as the 'Generic Model'
Category.
When placed, its elevation was set above the Cut Plane but below the Top of the Primary View Range for the Plan View. The Object displayed in its entirety. I then decided that this component was really better categorized as
'Specialty Equipment'. So, I re-assigned it in the Family Editor, and re-loaded it into my Project. As I did this, the object disappeared from Plan View. I then switched to a 3D View to verify it was still present in the model - and it was.
So why does Generic Model Display, and not Specialty Equipment, I ask? I've discovered that if I lower the Elevation of the Specialty Equipment to exist at or below the Cut Plane, but above the Bottom of the Primary View Range; it will display in Plan View. I've also tested and discovered that adding Symbolic Lines to the Plan View of the Specialty Equipment in the Family Editor and re-loading into the Project will not overcome this issue of elevation - if the object is above the Cut Plane the Symbolic lines will not display either.
I note that Specialty Equipment does not have a "Cut" setting for Lineweights in Object Styles, and Generic Model does. Is this the indicator for this display behavior that I'm experiencing? And if so, why is 'Specialty Equipment' regulated to this type of Category? Why not have a 'Cut' setting for it?
Quite a fair bit of an Architectural model gets lumped into this Category:
lockers, toilet accessories, kitchen equipment, medical equipment, etc.
I accidently deleted a section marker from a plan view. The section still exists and in shown in other plan views. I feel stupid for asking, but how can I get the section marker to reappear on the original plan view?
bring back my site plan view!, and the ability to use shadow and realistic material!because when did another site view i am unable to use shadow and realistic view!
I have created a "Jersey Barrier" as an adaptive component (attached). It is basically a profile extruded along a series of reference lines hooked to adaptive points.
In some plan views, under certain geometric configurations, the extrusion disappears in the view. The points highlight if you mouse over them. In a parallel 3D view, the component is still there. If I adjust the geometry in certain ways, the component will reappear in the plan view.
Here is an isolated view (3D on left, plan on right) with a configuration where the object does not appear in plan.here's a view where I have moved one of the adaptive points, and it appears in plan.