Is there a way to add the number of control points on the leaders? if i need to make it bend multiple times, is that possible?
currently i have two, one to control a "kink" and one to control the end point. can you add more to it or adjust a setting?
How to set 2 adaptive points (AP) to control the position and diameter of a circle. Have tried setting a ref plane driven by circle dia param but justs results in overconstrain when flexed. Is it possible to a) lock the centre to an AP and lock redius to AP?
Is it possible also to lock a ref plane to an AP so that the AP drives it rather than the other way round?
When I make my rooms for a building, I want them to be a specific distance from the previous wall, say 10'. But when Revit measures the walls, it measures from the center line of the wall and not the edges. How do I correct this so it is measuring from the nearest edge so I'm not constantly having to think about how thick the wall was on each side and manually add 5 inchs or whatever it is in order to get a solid 10' room.
Also, when placing rooms, I have found that the program keeps making the reference distances from points halfway across the house. For example, if I want to make a room 10'x 10', and go to place the top wall of the room. If there is another wall across the hall or something that may intersect if you extend an imaginary line, the reference dimensions won't be 10' from the bottom wall, but it would be something like 4' 5 7/16" from that other room that has nothing to do with the wall I'm trying to place. Does that make sense? How do I turn off or control the meaningless reference points?
I have a couple points that were part of an import event (data from a previous project) which I want to assign as control points for an incoming traverse, is there any way to assign those as control points? I can't seem to find a way to do that other than perhaps re-importing the specific points as control points and overwriting the existing ones.
View 2 Replies View RelatedIs it possible to have multiple leaders with one keynote?
View 6 Replies View RelatedAny export issue with Revit, where the leaders in the Revit model are exploded when the model is exported to AutoCAD. If so is there a setting or a procedure in Revit that fixes this other then redrawing the leaders in AutoCAD?
View 2 Replies View Relatedis it possible to change the line patern of leaders in text notes, from solid to dash or another one? I know I can change the tick type but can´t find anything for the line.
View 2 Replies View RelatedI need to use/write a iLogic code. I have a assy, in this assy i have parameter Height and Width. And it´s no problem to controlls this two rules/value.
But I have a problem with the rule when my height will control the number of parts
If my height is 500-1000, one part.
If my height is 1000-1500, two parts.
If my height is 1500-2000, three parts.
Is it best to use suppress or use a pattern in this case?
I just wondered if can I assign a particular ITEM number to a particular part, instead of relying on order in the assembly.
I unsterstand I can overrite it in BOM but can I have it controlled from the part, so any time I instert it into an assembly, this particular number in ITEM coulmn pops up?
1. With the pen tool/selection tools, if i've made a point and it has no control handles, how do i make it so that it has control handles?
2. If a point has 2 control handles, how do I delete one of them?
3. When im working on a path how do I make it so that PS doesn't create a vector mask based on that path every time I create an adjustment layer?
versed on controlling points in Illustrator, but some of those dont carry over to Photoshop.
I need to multiple select two control points on a box. Control, shift, other key combinations, etc. are not working. Control works in other apps; don't know why this is going on.
Any alternative to the key stroke for multiple selects in 3DS MAX?
In the screen grab here, you can see that "errors" in gradient smoothness coincide with control points..or maybe between certain control points....is there a way to prevent this error from happening?
View 7 Replies View RelatedI've VideoStudio x5 and I try to delete volume control points from my clip in the Sound Mixer. Tooltip says "Delete this control by dragging outside the clip" but it doesn't work.
View 2 Replies View RelatedPossible to view the control points of a 2d or 3d object. I know that we can view the control points for spline objects, but is it possible to view the control points also for every other object i draw?
View 2 Replies View Relatedwhat does it depends that how many control points are on an object in Designer Pro as default?
For example in Shape Tool creating a horizontal line (click and somewhere beside CTRL - click), at me it creates control points at the end of the lines plus two ones on the line.
That is super anyway because immediately can be seen where is the 33% of the line length, but could be set somehow this that how many control point should be as default?
When I select an element, in this case a building, to make changes, the entire file is selected instead of the building. There is nothing to ungroup when this happens.
View 1 Replies View RelatedIs it possible to create a shape and then edit the coordinates of the shape's control points? When I currently click on a shape's control point, it doesn't offer any way to fine tune the location of that point by manually typing in the X, Y coordinate.
View 2 Replies View RelatedIn Curves, when you want to see the deepest blacks and whitest whites, you hold down Option while clicking and dragging the balck and white sliders – and the dragging doesn't allow accurate control. It's okay, but I would find it better if I could nudge the black and white sliders from the keyboard while seeing the effect on the image. Is that possible when using Curves as an adjustment layer?
View 12 Replies View RelatedHow does one implement the use of two pivot points to control movement concurrently in the X- and Y-plane?
I 've added a Link Constraint to the salmon colored component which is linked to the red cylinder pin at far left. This pin has a Path Constraint to an Arc path which is orientated left-to-right and arching up. The pin at right has a line Path Constraint that moves down and to the right. Still image 01 shows the retracted position. Still image 02 shows the animation at 50%, the Fowler hinge follows nicely the path of the left most pin quite well. Notice no movement occurs in the down direction that would be imposed by the right pin - if it worked/was set up properly.
Any way of viewing the coordinates of the Control Vertices (Control Points) of 3d or 2d NURBS Surfaces. I tried to use the "properties" of the 3d NURBS surface that i designed but i could not find them anywhere..
i would also like to ask if it is even possible to export these coordinates to txt or even more to Excel.
I have a question for all the mold designers out there! How do you control the number of side actions when designing multi impression tools?
I recently completed a job for a customer where the requirement was to have a 2 impression tool with one side action to control both of the impressions. I found that if you pattern a part within the mold design environment and then apply a side action, the side actions would be copied to each of the patterned parts. I have created a test part to try and illustrate this (which is way out of size and proportion!):- Even if I combine the inserts, I still get the same effect.
Is there's any LISP or Program that can increase the number of points in 3DFace?
View 6 Replies View RelatedI have a problem reducing the number of points that are to dense. they are so close together they basically form a line. problem is that there are about 5000 points at the line were I want to be 50 of them. deleting them manually would take forever...Is there a command that can reduce no. of points at one area?
I have ACAD2008 Civil
I am trying to set several hundred points along polyline verticies with the point number starting at 5000. There are no other points in my drawing, yet everytime I start the process, it begins at 1. I have set 5000 at my Next Point Number under Point Identity in the Create Points toolbar. I have also verified that the 'Save Command Settings" is set to yes under the 'Commands-Create Points'. We cannot get this to behave as desired.
This is a 2D polyline with no elevations.
Running C3d 2012 here, but haven't used prior versions. I'm using fieldbooks to import survey data. If there is an error of some kind and I "Re-import event" for the fieldbook, then the occupied points from the field book are deleted out of the survey database and I get the resulting error of "point invalid" during the import. My fix is to go into my control drawing and import the control points from the drawing into the survey database then run the "re-import" again.
View 9 Replies View RelatedI need to copy shapes over from Illustrator to Powerpoint. Now I'd like to maintain my groups so that I can ungroup them later in Powerpoint. Is that possible? Ideally, Illustrator would copy them in a way for me to change handle positions in Powerpoint later on.
View 17 Replies View RelatedI have a point cloud with 161 million points in it. This is basically fine and works well but I need to create equally high resolution surfaces from certain regions of the point cloud. No matter what size I choose my export shape, it will only create a surface from a ridiculously small 750,000 odd points, a 'feature' which has been documented on these forums before. I have POINTCLOUDDENSITY set to 100.
My question is, how can I build a surface from this high resolution point cloud data that has more than 750,000 odd points?
I'm thinking about mosaic'ing - ie. making several smaller surfaces over the required area and pasting them together.
In AutoCAD leader settings you can set the number of point so the leader looks standard. I am searching for this in inventor and am coming up empty. I have seen other engineering drawings where I can tell that the generated data in the balloon was entered from the parts column in the B.O.M. But instead of part numbers, I have seen text. and I have mine set up to generate the Balloons that way but I do not like the leader type it is giving me. The attachment is what my leaders are looking like in inventor.
View 1 Replies View RelatedI've got two trajectories from the bottom of two tires and I want to create a road surface, an object whose shape will match the trajectories, thereby creating a perfect shadow catcher.
The trajectories are virtually identical in shape and number of points because the two point helpers that created them were wired together. I've converted them into splines and messed with the loft tool, with not so good results. I ended up brute forcing the shape of the object into some kind of shape but I think there has to be a good, dependable way to do this in a program like max.
Any way to reduce the number of vertex points in a polyline or 3d polyline and retain the basic shape but without having to redraw over the top it?
Ideally, I would like any adjacent segments which are in the same direction as each other to become one segment.
In my image you can see the number of points it has, the majority of which are not necessary for my needs (it was imported from a client's drawing). My desired linetype will also not show because of this.
spline.jpg
C3D 2013. 64 bit. Windows 7.
Question 1.In C3D 2013 is there a ceiling to the number of points allowable in a C3D surface? Is it 1.5 million?
Question 2. In C3D 2013, when creating a surface from Point Cloud data is there a maximum point count based on the answer to question 1 - or is a different point count limit applied?