I would like to draw a Zig Zag Line, but I want that the line start in point "A" and finish in point "B".
The image below is similar to how I want the line, but I would like to have that "wavy" style. I use Illustrator CS6.
When I have been drawing things I often want to start drawing from an existing line but not on an existing node/end point/mid point etc. For example I need to draw a support collumn on a wall 20' from a corner, but everytime I start it will snap to the nearest endpoint or midpoint.
A similar problem is if I am trying to draw a rectangle that is centered on the midpoint of another object. The rectangle tool will snap to the midpoint and the placement will be off by 1/2 the width of the rectangle.
This is not an osnap issue, but more of a best drawing practices question. In the past I have used DIMLIN to create a node to snap my starting point to, or drawn a new line out to the point where I want to start. I don't like doing this because then I have to erase it later(just to keep the drawing tidy).
I need to design a walking track 1 mile (5280 feet) from a starting point and finishing at the same point. I need to go around buildings, ponds, etc. What is the best way to tackle this? I thought about 16 splines at 330', but as soon as the spline is moved the distance changes.
View 2 Replies View RelatedWhen trying to draw a line and choose a starting point, autocad decides that this is wrong and start the line in a different place. I've turned of autosnap and autotrack but this dosen't work.
What is it that I've forgot to turn off?
How to choose my starting point to be relative to another point without drawing help lines (which mean they must be drawn, selected, deleted = time).
For argument's sake, consider I am attempting to draw a cross. I use the line command, input a starting point; choose next point: @100<0 (to draw a line 100 units in length at an angle 0 [relative to X axis] relative to previous point).
Now I need a vertical line of equal length to cross the middle-point of the horizontal one.
I could snap to middle-point, draw a line of half-length at angle 90 and draw another of 2.(length) at angle -90. This produces 2 lines one of which is unwanted must therefore be selected and deleted.
This simple example illustrates my point.
I need a command which allows me to choose my first point (for the LINE command) as the point which is "X" units at angle "alpha" relative to a point "x,y" (or a coordinate selected by the SNAP tool if you will).
I have had this problem since I started using patterns. Basically when I put a pattern on a path I want to then move it along that path so it starts where I want it to start, not neccessarily on the path's starting point.
There is an image of how it looks like
I created a simple pattern to show my issue. For example I want to move this pattern along this circle so it looks like this (triangle points up)
As you can see I rotated the whole circle to get the right outcome I need, but if it was just a regular path I would not be able to fix it this way.
Is there a way to do that? Something like moving text along a path.
I am using Illustrator CC.
I want it to be a variable stroke, so I loaded up “Width Profile 2” in the profiles. The trouble I am having, is that Illustrator defaults to start the larger dots in the bottom right hand corner, and I would like the “starting point” to be in the middle of the line if you know what I mean. I'm still happy for the dots to start big, then gradually decrease in size, but I want to control where the “beginning” is.
View 2 Replies View RelatedI'm trying to draw a plan of my house in Autocad 2009 but I seem to be endlessly using trim and extend because I can't easily select the points that I want with osnap. Eg. imagine I have a box, and I want to start drawing another box inside it that has each side as 10 units smaller than the corresponding side on the outer box.
Step 1 - I draw a small line from the top left corner of the big box using the endpoint snap, typing in "5" for the length.
Step 2 - I then do the same at right angles to the first line to get me to the starting point of the inner box. This always leaves me with 2 small lines to remember to delete.
Step 3 - Then in order to draw the top line of the inner box I end up drawing to a random length because I can't say "draw until 5 units away from the right hand side of the big box", then I end up trimming it later once I've repeated steps 1,2 and 3 for the next side of the inner box.
I know in my example above I could have scaled the box down or something but that's not what I'm getting at. I really want a way of selecting line start and end points that are a known position away from an existing point.
Having a lot of issues manipulating points on paths in Illustrator CC - this is a fundamental feature of creating vector graphics and it's very annoying I'm paying for this and it's just not working. Eating up a lot of my time simply because I can't select or convert or add the anchor.
View 2 Replies View RelatedI have a VBA to insert a block I ask the user for an insertion point GETPOINT. Then I allow the user to select an angle. GETANGLE starting with the insertion point. If the user picks a point or enters a number there is no problem.
However if the user hits enter it crashes saying invalid input. What I want to happen that if enter happens it accepts it as an angle of 0.
How does one erase part of a circle from point to point ?
View 2 Replies View RelatedI am lost were you can put an arrow point on either end of a line, where do i find it
View 9 Replies View RelatedI noticed that if i draw a very short line (about 10 pixels or less) then cursor shifts back to starting point.
Tested on systems an drivers:
Mac OS X 10.6.4 or 10.7.4
Driver 6.3.0 or 6.3.3-3
Photoshop CS 5 (12.0.4)
Photoshop CS 5.5 (12.1)
Mac OS X 10.8.2, Driver 6.3.3-3 and Photoshop 6 (13.0.1) - same problem.
I have three Intuos 5 tablets for now and all have this bug so this is not a hardware problem i think. Corel Painter 12 - all good.
I do aerial photography with a large rc helicopter. Camera movement is hard to get rid of. I am looking forward to the upgraded Warp stabilizer "VFX" to work with that. I have been using the Warp in AE and motion tracking. I just don't know how to launch the multi point program in AE cloud.
View 1 Replies View RelatedI am trying to rotate the stroke on an end point of a line that I've drawn. Is there a way to do this while keeping the line in tact?
Before:
Desired Effect:
Notice the top point on this line. I've faked the rotation that I'm talking about. Is this possible to do without destroying the line, adding a white element above it to look like I cut if off, etc.?
I was doing the following steps when I encountered this problem:
1) I created a V shape with the Pen Tool.
2) After having changed my default selection tool to the Direct Selection Tool (so that I can use it later), I used the Convert Anchor Point Tool (Shift-C) to drag at the V junction to change it to more of a U shape & thus also creating a Smooth Point there, like this:
3) Then I grabbed one of the direction handles & dragged it a bit to make it a Cusp point. Like this:
As soon as I did this, the other direction handle disappeared & the anchor point also became deselected.
4) So I temporarily switched to the selection tool (the Direct Selection Tool in my case) by holding down the Cmd key and clicked on the anchor point.
Result: As soon as I clicked on the anchor point to select it and also make the other direction handle visible, the anchor point became a smooth one & the shape of the path changed dramatically - i.e., the cusp point I created was gone (see fig.)
and I had to rework on the changed path.
Is this expected? BTW, I'm working in Illustrator CS6 (Mac).
I have a curved path I imported into Illustrator, and I'd like to draw a line perpendicular to the curve at a particular point. I've searched google and this forum, but can't find any description of how to do it. Corel Draw has a button that lets you do this, so I'm hoping something similar exists in Illustrator...
i'm currently just calculating the angle at the point I want using the derivative, finding the angle, and then adding 90 degrees to it. But I need the line to be placed at a particular point, and the X/Y properties of the line are based on the ruler which isn't even in the center of the document (I want to position it relative to the artboard). As in, I just want to set the position of one endpoint of the line...
How can I draw a line from the endpoint of an existing line (snap to grid is on), without the lines being joined? Joining causes two problems for me:
1. The arrowhead at the end of the existing line moves to the end of the joined line, whereas I want the arrowhead in the middle of the combined line.
2. Even without entering isolation mode the new line gets joined to a line which belong to a group, thus becoming part of that group as well. This defies the use of grouping to create logically connected units.
I'm using CS4 on a mac.
Here's what I want: a filled rectangle in which the top and bottom line segments are straight, and the two side line segments are zigzag. I can't seem to find a good way to do that.
First thing I tried: Make a rectangle, then Effect > Distort & Transform > Zig Zag. That turns all segments of the rectangle zig zag, and I want the top and bottom to be straight.
Next: Draw four separate lines and join them to make a shape that I can fill. I can do that, right? Anyway, the problem: I draw a zigzag line, and a straight line and right angles. I select the endpoints with the pen tool (right?) to join them. When they join, either they both become straight or they both become zigzag. Which is not what I want either. Here's a picture of what I'm trying to do.
The other thing I noticed is that the Zig Zag effect doesn't give me additional anchor points (at least from what I can see), and doesn't give me anchor points where I want them. See in the above picture, where I have the left-hand line segment selected, the path is still straight so the anchor points don't line up with the zigzag line that is visible to me. Which means when I try to join the segments, they make funny shapes at the corner. Which is also annoying. This thread seemed to indicate that Zig Zag should give me additional anchor points at each corner: [URL]. Why don't I get that? Is it a CS4/CS5 issue?
I made a long line with a complex stroke profile. I decided to remove a section, but it distorts the new ends with the excess profile. How can I delete a mid point on a line and keep the profile visually intact?
View 5 Replies View RelatedThe above image shows my problem. All have the same zig zag effect setting, but due to inconsistent anchor point spacing there is inconsistent waviness. Is there a way to make a wavy line that is not a distortion based on anchor point distances? I'd like all my wavy lines to look nice and consistent like this:
The only reason they're so consistent is the absolute setting has been used but these lines are all straight and have only 2 anchor points, start and finish, hence the wave is consistent. It's harder when the lines are curvy and have a different number and spacing of anchor points.
I would like to create a wavy line (the zigzag feature is not exactly what I need here) to outline a shape and then fill it with a solid color.
This is approx what I want; however the undulation needs to be more round and less peaked.
I have a path with a smooth point. The two direction points form a direction line with any non-45-degree-angle - say 11.8 degrees. I want to drag one direction point while keeping the angle of exactly 11.8 degrees.
Is there a key combination for that (Mac OS)?
I have a line or a pline segment and i want to start a line from a point laying there and go perpendicular outwards. Is there a way to do it with tracking?
Yes, i saw the command draw line at an angle but i find it a little bit complicated for a simple task like that. I am sure autodesk have a simplest solution about that.
If i am already at the draw line mode and i can easy catch the tracking perpendicular to previous segment but if i want to start from another line and go perpendicular i cannot make the tracking work.
I need to find a way how to insert a point or a * on the center point of a hole and put it on a different layer. The reason for this is - I am a CAD tech for a welding shop and we cut parts out of steel and we use the dxf file format for our plasma table to cut parts. For example : if i have a 1 inch thick plate and want to put a 3/4'' hole in the plate the hole will be distorted because the hole is smaller than the material thickness. For these situation we can use the plasma table to burn a point or a dot on the center point of the hole. But to do this the point or dot must be on a different layer in the dxf.
View 2 Replies View RelatedI am looking for something a lisp or program that would do a light point by point of fixtures in a plan.
[URL]
Civil 3d 2012..I used 3d orbit, it crashed. My points, point groups and newly updated description keys are gone.I have looked at all my backup files etc, and they do not want to display.
View 4 Replies View RelatedIm still new to Civil 3D and i would like to know how to connect inported points using 3D polylines. I imported my points from Excel in a PNEZD format. How do i get the 3d poly line to snap to my points so I can Connect them? someone mentioned using a feature line to connect the points but im not sure how or what that would do.
View 3 Replies View RelatedWhat's the difference between the "Point" Parameter and the "Base Point" Parameter in the Block Authoring Parameter Pallet?
HP DV7 Laptop
Intel Core i7-3820QM 3rd Generation Quad Core 2.7 GHZ CPU
16 GB DDR3 RAM ( 2 DIMM ) / 180 GB SSD
Nvidia GeForce 650M Graphics w/2 GB Memory
Windows 7 Professional 64 bit / AutoCAD Civil 3D 2014
I have a database of points I am trying to import, and the point data for each point includes a hyperlink. I've created a set of custom User-Defined Property Classifications for all the data types in the point database, and I've created a point file format to use to import the points.
It's a database of existing curb ramps, the data includes things like widths, slopes, some text, and a hyperlink to the Google Streetview at each ramp. I've created a custom point label that will show the data I need to see at each ramp.
All goes great except that the import fails because of the hyperlinks. I've tested it by removing the hyperlinks from a small test portion of the data set, and the test points are then successfully imported. I suppose I can delete the hyperlinks from the entire database, but if there is a way to include the hyperlinks in the point import I would prefer that.
Win 7E 64-bit, Intel i7, 12 GB
C3D 2012
In uploading the Point input data into the AutoCAD Civil 3D 2013 software program, is it possible for me to add more Point Attribute items after Point Number, X, Y, Z? I need to have the chemical results/data attached to the (sampling) Point that has the Point #, X, Y, Z - like Point Number, X, Y, Z, Arsenic, Lead, Mercury in the input .txt (or .csv) file.
View 9 Replies View Related