AutoCad :: Plotter Doesn't Print Out Colors
Jul 18, 2012
I have just installed AutoCAD 2012 and a HP Deskjet 510 plotter. The plotter does not print out the colours in true colour i.e. when the line on the CAD file should print in red, it is actually printing out in orange. There are also problems with other colours not printing out as they should.
I have printed PDF documents to the plotter and using this route the colours will print as they should so the problem is not plotter related. I suspect its something to do with the AutoCAD
View 8 Replies
ADVERTISEMENT
Mar 8, 2011
I have a new machine with windows 7 64 bit and autocad 11. When I choose the 6204 as my plotter I get the following message : "This plotter configuration cannot be used for one of these reasons: the driver cannot be found, the device cannot be found, or the driver has a problem. The None plot device has been substituted." it does not matter if I choose to try and print to the plotter or make a PDF this error comes. up..
View 8 Replies
View Related
Jun 14, 2011
I recently stopped using my HP755 plotter and am now plotting "dwg to pdf". The problem is when I go to plot I get a warning message stating that "this plotter configuration cannot be used" and it goes on to list a few reasons why and selects the "none" plotter. Then when at the plot setup page I can continue to plot as I normally would. Why am I getting this warning and how do I stop it?
View 2 Replies
View Related
Dec 6, 2000
I just got Autocad 2000i as an upgrade from 13 and 14. I have a summagraphics HiPlot 7200.It was set as a windows system printer on the old autocad versions, 2000i will not accept the widows driver (which works great on the old systems) and i have to use hpgl emulation wich sucks on 2000i
View 2 Replies
View Related
Jan 2, 2003
We recently made the switch from R14 to 2000. In the LONG process of trying to figure out plotting in 2000, I ended up having a lot of plotter names to select from when I go to plot. We have 2 HP 450C plotters and 2 printers (HP5000N & HP 1220C) and I only have one pc3 file for each on the server. I want to nknow how to remove some of the plotter names from ACAD and have only the 2 plotters and 2 printers to choose from when you go to plot.
View 6 Replies
View Related
May 20, 2011
I was wondering if there is a way to set the plotter to cut directly after the drawing. i have changed the setting to extent but it still prints the whole page size.
View 9 Replies
View Related
Jul 30, 2012
I'm trying to plot a pdf file that is approx 1MB. We have a HP designjet 500 plus, with 32MB of Ram. When I try to plot it though, The plotter displays a messag: 'Out of memory. Data Lost'. I unfortunately only have the PDF file. Is there any way for me to plot this file?
I tried to print it as a pdf by using a virtual pdf printer, but the end result is the same.
View 1 Replies
View Related
Mar 21, 2012
I need to change printer/plotter (maybe PC3 file) on my drawings. For example I have 'printerN.pc3' setted and I need to set 'PrinterM.pc3'. Also need to change print scale. But since I have many drawing I need somithing thatcan do iy automatically. So what I need:
I need to replace specific plotter to anither plotter:
1. For example if plotter setted to "HP" -> change to "Canon"
2. If paper size (2) is A3, set Plot scale (3) to 1:1.015, if Paper size (2) - A4, set Plot scale (3) to 1:1.02
Seems like I can do it with AutoLISP.
*** Using AutoCAD 2009 and 2011***
View 2 Replies
View Related
Jan 27, 2012
I have problem with AutoCAD DWG to PDF printer. When I use a vector drawing with a raster map attached and print the layout with the DWG to PDF printer, all the vector elements looks perfect in the output pdf file, but the raster image is almost unreadable. It doesn't work if I increase print resolution and it looks if there would be some kind of default jpeg compression inside this printer but there aren't any settings to control it or simply turn it off. After plotting such a drawing on the HP plotter it is so awful that there is no use of such a file.
View 9 Replies
View Related
Nov 16, 2007
I get this message when I go to print in acad 2008.The following shortcuts in the plotter search were invalid and ignored: (invalid path is displayed here...) ending with .ink.The path exists and yet it says invalid and ignored. I hit OK and it continues to the plot dialog and everything works. How to correct the path or disable the dialog... I looked in the options/files(tab)/printer support file path and they are setup to our printers, but the error continues to pop up.
View 6 Replies
View Related
Jan 17, 2012
I don't need the capability to print directly to a plotter, but I need to set up a dummy plotter to generate plt files that will be changed to tif files with our Kip. Any plotter driver that works for this situation? Every one I have tried has generated a plt file, but the Kip would not convert it or open it.
View 8 Replies
View Related
Oct 17, 2012
how to print two separate A2 drawings side-by-side in A1 paper space on an HP plotter? I'm assuming that this would be handled by a third party print management software or something along these line. I'm looking for any solution to save on paper!
View 1 Replies
View Related
Dec 17, 2013
I have a question about plotting at Canon plotter (Canon imagePROGRAF iPF750) with possible has feature to plot as a drawn area.
Simply say I want to specified only one custom/roll paper size, make it custom size as a default. After that I want to plot exactly the accurate drawn area from my dwg. So with this settings I cannot specified custom paper size for each unique dwg.
For example I'm using this settings with another plotting device -- Xerox WF (picture to see the chosen settings) and working like a charm.
View 1 Replies
View Related
Apr 23, 2012
Although automatic rotating is on, the HP plotter DesignJet 500 plus uses the paper wasting method.
In the layout preview of Civil 3D 2012 the result looks good, but I need one meter of the paper roll for this plot.
View 2 Replies
View Related
Jan 28, 2014
I have a DesignJet T1100ps and a DesignJet Z5400. I have a PDF from a client that has 2 pages that are ARCH D size and 3 pages that are 11x17. All pages in the PDF came from AutoCAD 2013 paper spaces. The plotters are in offices 50 miles apart.
When I print to the T1100 and state pick page size by PDF page size and choose the option actual size the plot print correctly. The plotter will nest the pages and print to scale. I get 2 Arch D pages and 3 11x17 pages.
When I print to the Z5400 the pages get changed to ANSI D pages and get cut off because there are 2 inches of paper missing. If I shrink the plot I can print them so they are not to scale but fit inside the ANSI D size page. This doesn't work when we need scale drawings. The Z5400 and the previous DesignJet 800 both have this issue.
Due to the distance of the printers I can not plot at one office for use at the other. I would like to try and solve the issue via software if possible. So far my only work around is to pick ARCH D in the plotter driver and print all pages to ARCH D by shutting off the option to print pages by PDF page size. This wastes a lot of paper because we print actual size. I can also print one page at a time.
We asked for the drawing and were able to get an original copy but it is GSA and they typically do not provide the originals. If I print form the drawing directly to the plotter from AutoCAD everything comes out the right size. AutoCAD also generates the PDF file correctly according to the page properties.
What might cause Adobe to change our CAD prints in a PDF from the ARCH D size to ANSI D size for this Z5400 plotter?
View 2 Replies
View Related
Nov 8, 2012
In the process of releasing 2013 to the office. We have about 60 machines being loaded, varying from 64-bit Win 7, 32-bit Win 7 and 32-bit Win XP. I have gone through and created new PC3 files for our two KIP printers (3000 & 7000 series). I added one custom page size to each to create a PMP that goes along with them. These files have been placed onto a network folder for all users to access. This is where my confusion begins.
When other users go to utilize these files it is giving an error stating that "the plotter configuration cannot be found, driver cannot be found, device cannot be found, yada yada. The none has been substituted."
So we began to look at the PC3 files and see what the issues are. When the same file on the Server is copied down to a local machine it changes back to a KIP10 driver down from a KIP11 driver on the network. Make Sense?
In order to fix I began running the "Add-A-Plotter Wizard" on the local machine. Created a new PC3 wiih a different name and went back into the program. Now the PC3's that did not work before WORK.
In short, since the 2013 version has a new file format do we have to run the "Add-A-Plotter Wizard" on all local machines before the standard PC3 file will work effectively? Or does having 2011 version still on the machines have an effect on these files?
Win 7 Pro 64-Bit - Dell T1600
Intel Xeon 3.30Ghz
8Gb RAM
Civil 3D 2013
View 1 Replies
View Related
Aug 20, 2013
I'm using 2008 and trying to get one side of my plots to be 1/2" from the edge of the paper (from one of the ends, not the sides). When plotting from R14, our plotter understands just fine and prints a standard ARCH D sheet just the way we want it. With 2008, our standard sheet template sits outside the dashed line that indicates plottable area.
I think that autoCAD thinks that the printer can't print that close to the edge, but obviously it can. I've gone into the 'modify paper sizes' options and adjusted the bottom margin to allow enough space for the plot. Plot preview looks fine and nothing is getting cut off, but when I actually print, the printer just prints an extra inch of paper past the margin I redefined so I end up with a sheet that is 24 x 37 and the edge of the plot is still not 1/2" from the edge of the paper like I need it to be.
We are trying to move from R14 to 2008 (and eventually 2014) as the office standard and this is the last hurdle that is baffling us.
View 4 Replies
View Related
Oct 24, 2012
I made an attempt at drawing out what I'm trying to say in MSPaint. At my office we use an HP Designjet 800ps to plot our drawings, most everyone uses AutoCAD 2010-2011 and I use AutoCAD LT 2010. All of our drawings are ANSI C size (17"x22") and we use paper rolls that are 24" wide x 150' long. For some reason our plotter always prints our drawings sideways causing us (read 'me, the assistant') to have to trim the excess off of every single print. Not only is this time consuming but it is a huge waste of paper! If I can get it to rotate we will get 19 MORE plots out of every roll of paper!!!
I was wondering if there is some way to change settings somewhere so that our drawings are printed the correct way, saving me lots of time and saving our company lots of paper? Is it normal to plot this way?
View 1 Replies
View Related
Jun 20, 2013
How do I get the built-in PDF plotter quality up to my adobe pdf plotter. I want to do use publisher and make mulitple page pdf's and as I understand it I have to use the built-in plotter to do it. As of right now I have to sperate pages with adobe and then combie them to make a single pdf.
(how the built-in PDF plotter looks)
(How I want to have the built-in plotter look.) Without changing settings in my pdf viewer, I need to be able to send these out to customers.
I'm useing AutoCAD LT 2010
View 9 Replies
View Related
Jun 25, 2013
For years, we've been printing large documents to our plotter without issue. Suddenly last week, nothing large will print.
I've seen a few different error messages, and have tried different computers, and different versions of Illustrator, but nothing large will print.
When trying to print, I currently get the following:
I've also seen an error suggesting not enough memory is available, which is bogus. And I think another error that was more vague, something to the effect of "can't print"
I've setup a clean install of illustrator on a clean windows install, same issue. I setup an alternate print server with our rip software, same software we've been using for years. Same error on the alternate server.
Nothing changed, and it's effecting everything here, and new installs. I don't know what happened, but this is getting critical, we need the ability to print.
View 12 Replies
View Related
Jul 7, 2013
Just wanted to print a new photo and realized that the colors in print preview do not match the colors in soft proofing. In both cases I selected the same icc profile and rendering method. The print colors matched the colors in print preview. I never had a problem so far. All new prints will be checked with soft proofing and adjusted when necessary. I never paid attention to the color rendition in print preview and all prints perfectly matched the colors from the soft proofing. I was surprised when my print came out of the printer and the colors weren't matching the soft proofing colors, but that of the print preview.
I don't understand why Photoshop renders the colors differently in the first place. See attached screenshot for the difference in the blue/cyan colors. I don't care if the print view colors will match the print, but I do care when soft proofing is not working.
View 2 Replies
View Related
Jun 25, 2013
In AutoCAD 2014 and ASD2013 I cannot choose one of the printer, which is installed on Windows (OCE TDS600). It is strange, because Autocad sees it on the list of available plotters, but when I try to select it - it automaticly changes to "None".
The plotter is properly configured - I can print with it from Revit 2013 without any problems. Also when I switch account to any other (on that same computer) everything works fine.
I tried to add this plotter through "Add-A-Plotter Wizard", but each time I obtain an error massage "Autodesk Hardcopy component failed..."
[URL]
View 2 Replies
View Related
Jan 16, 2009
So I am working on this document and it has silver background. I go to print preview (Photoshop cs3 and cs4 on Vista) and I get color looking more like bronze looking but when I do print, it comes out just like it should (in working mode which is Monitor RGB with Proof colors checked).
This setting is the only one I've used to make sure image/psd looks exactly like what it should when printing. I tried the default Working CMYK with and without Proof colors but it's still showing me the bronze look instead of silver. I've looked on the net and no exact easy fix for this was found. I really really appreciate any help.
Another simple question is regarding size. I'm working on a document size of 17.5 x 8.7 inches and the actual Banners will be printed at size 175 x 87 inches (5 banners each at 35inch wide but combined into a big one). So essentially, I'm working at 10% the size of what the final print will be and my file size is 760mgs. You can only imagine how big the file would be if I work on the actual size.
View 4 Replies
View Related
Oct 13, 2012
How do I get my photos printed? I select a photo but I get the maessage that no photo was selected.
View 2 Replies
View Related
Jul 28, 2011
I'm running Windows 7 64Bit running Adobe CS5 Master Collection. But ever since I allowed CS5 Photoshop to control my printer (HP Photosmart Prem 310-C) to do a test print of a graphic that I created all of my Blues print a violet/blue color, no matter what color blue. It has even affected MS Word & MS Project when I try to print blue colored font or Gantt Chart blues will no longer print blue, but will print the same blue/violet color. I've even tried a brilliant blue which will all view great, but prints the same shade of violet blue! All my colors and Blues will view great! I've calibrated my monitor and I've reset my printer several times and still the same thing! I never had this problem before I downloaded Adobe CS5! A strange thing is that I can run check printer test and the data & image that is stored in the printer will print blues perfect, including running a copy direct from the scanner bed and it will produce perfect blues. I almost feel as though Adobe CS5 has possessed my PC and printer, how do I get it back to printing like it did before installing CS5 Master Suite?
View 2 Replies
View Related
Apr 26, 2012
I believe I have done this successfully before so I'm not sure what the problem is. Here is the situation.
AutoCAD 2013 Windows XP I have a drawing (Drawing A) that contains a PDF (using PDF attach) with text over the of it. I then have this drawing Xref'd into another drawing (Drawing B) in model space. When I print this drawing (Drawing B). The text prints but the pdf does not.
View 2 Replies
View Related
Jan 11, 2013
I have a problem when I print documents regardless of the printer I use.
If the document is on the network, colors are printing in black.
But if I copy this document locally on my computer, colors are printing normally.
Note : I'm using AutoCAD 2012 LT
View 7 Replies
View Related
Jul 30, 2013
I downloaded (from someone) a simple dwg cad file, that had 255 lines, each with a different autocad color (colors 1 thur 255). I used it to plot with different ctb files, so I could see at a glance the lineweight the color printed.
View 4 Replies
View Related
Mar 15, 2012
I've just replaced all the color carts in an HP DesignJet 510 42-inch inkjet plotter. I drew some parallel lines in ACAD 2012 to test the colors, and I'm getting weird results. The most noticeable errors are: Yellow prints out at a very pale green and Blue prints at purple. Red and Cyan seem to be ok, as well as Orange... I ran a color calibration on the plotter itself and the yellow prints out a very bright, correct yellow.
View 2 Replies
View Related
Oct 4, 2011
I'm trying to print in black & white, everything works except the true colors, i've selected a b&w ctb file were all the colors are turned to black & selected a printer to print b&w. I've even copied contents into a new file but still the true colors are printing in color!!
View 1 Replies
View Related
Jul 8, 2010
I just started a new job a couple weeks ago where they use AutoCAD (I have been using Microstation v8 for the last few years). I completed a drawing and printed it in black & white. Everything looks great except the yellow lines. I want them to print black instead of light gray.
View 8 Replies
View Related
