I'm trying to plot a pdf file that is approx 1MB. We have a HP designjet 500 plus, with 32MB of Ram. When I try to plot it though, The plotter displays a messag: 'Out of memory. Data Lost'. I unfortunately only have the PDF file. Is there any way for me to plot this file?
I tried to print it as a pdf by using a virtual pdf printer, but the end result is the same.
In AutoCAD 2014 and ASD2013 I cannot choose one of the printer, which is installed on Windows (OCE TDS600). It is strange, because Autocad sees it on the list of available plotters, but when I try to select it - it automaticly changes to "None".
The plotter is properly configured - I can print with it from Revit 2013 without any problems. Also when I switch account to any other (on that same computer) everything works fine.
I tried to add this plotter through "Add-A-Plotter Wizard", but each time I obtain an error massage "Autodesk Hardcopy component failed..."
[URL]
I have a new machine with windows 7 64 bit and autocad 11. When I choose the 6204 as my plotter I get the following message : "This plotter configuration cannot be used for one of these reasons: the driver cannot be found, the device cannot be found, or the driver has a problem. The None plot device has been substituted." it does not matter if I choose to try and print to the plotter or make a PDF this error comes. up..
View 8 Replies View RelatedI recently stopped using my HP755 plotter and am now plotting "dwg to pdf". The problem is when I go to plot I get a warning message stating that "this plotter configuration cannot be used" and it goes on to list a few reasons why and selects the "none" plotter. Then when at the plot setup page I can continue to plot as I normally would. Why am I getting this warning and how do I stop it?
View 2 Replies View RelatedI just got Autocad 2000i as an upgrade from 13 and 14. I have a summagraphics HiPlot 7200.It was set as a windows system printer on the old autocad versions, 2000i will not accept the widows driver (which works great on the old systems) and i have to use hpgl emulation wich sucks on 2000i
View 2 Replies View RelatedWe recently made the switch from R14 to 2000. In the LONG process of trying to figure out plotting in 2000, I ended up having a lot of plotter names to select from when I go to plot. We have 2 HP 450C plotters and 2 printers (HP5000N & HP 1220C) and I only have one pc3 file for each on the server. I want to nknow how to remove some of the plotter names from ACAD and have only the 2 plotters and 2 printers to choose from when you go to plot.
View 6 Replies View RelatedI was wondering if there is a way to set the plotter to cut directly after the drawing. i have changed the setting to extent but it still prints the whole page size.
View 9 Replies View RelatedI need to change printer/plotter (maybe PC3 file) on my drawings. For example I have 'printerN.pc3' setted and I need to set 'PrinterM.pc3'. Also need to change print scale. But since I have many drawing I need somithing thatcan do iy automatically. So what I need:
I need to replace specific plotter to anither plotter:
1. For example if plotter setted to "HP" -> change to "Canon"
2. If paper size (2) is A3, set Plot scale (3) to 1:1.015, if Paper size (2) - A4, set Plot scale (3) to 1:1.02
Seems like I can do it with AutoLISP.
*** Using AutoCAD 2009 and 2011***
I have problem with AutoCAD DWG to PDF printer. When I use a vector drawing with a raster map attached and print the layout with the DWG to PDF printer, all the vector elements looks perfect in the output pdf file, but the raster image is almost unreadable. It doesn't work if I increase print resolution and it looks if there would be some kind of default jpeg compression inside this printer but there aren't any settings to control it or simply turn it off. After plotting such a drawing on the HP plotter it is so awful that there is no use of such a file.
View 9 Replies View RelatedI get this message when I go to print in acad 2008.The following shortcuts in the plotter search were invalid and ignored: (invalid path is displayed here...) ending with .ink.The path exists and yet it says invalid and ignored. I hit OK and it continues to the plot dialog and everything works. How to correct the path or disable the dialog... I looked in the options/files(tab)/printer support file path and they are setup to our printers, but the error continues to pop up.
View 6 Replies View RelatedI don't need the capability to print directly to a plotter, but I need to set up a dummy plotter to generate plt files that will be changed to tif files with our Kip. Any plotter driver that works for this situation? Every one I have tried has generated a plt file, but the Kip would not convert it or open it.
View 8 Replies View RelatedI have a question about plotting at Canon plotter (Canon imagePROGRAF iPF750) with possible has feature to plot as a drawn area.
Simply say I want to specified only one custom/roll paper size, make it custom size as a default. After that I want to plot exactly the accurate drawn area from my dwg. So with this settings I cannot specified custom paper size for each unique dwg.
For example I'm using this settings with another plotting device -- Xerox WF (picture to see the chosen settings) and working like a charm.
Although automatic rotating is on, the HP plotter DesignJet 500 plus uses the paper wasting method.
In the layout preview of Civil 3D 2012 the result looks good, but I need one meter of the paper roll for this plot.
In the process of releasing 2013 to the office. We have about 60 machines being loaded, varying from 64-bit Win 7, 32-bit Win 7 and 32-bit Win XP. I have gone through and created new PC3 files for our two KIP printers (3000 & 7000 series). I added one custom page size to each to create a PMP that goes along with them. These files have been placed onto a network folder for all users to access. This is where my confusion begins.
When other users go to utilize these files it is giving an error stating that "the plotter configuration cannot be found, driver cannot be found, device cannot be found, yada yada. The none has been substituted."
So we began to look at the PC3 files and see what the issues are. When the same file on the Server is copied down to a local machine it changes back to a KIP10 driver down from a KIP11 driver on the network. Make Sense?
In order to fix I began running the "Add-A-Plotter Wizard" on the local machine. Created a new PC3 wiih a different name and went back into the program. Now the PC3's that did not work before WORK.
In short, since the 2013 version has a new file format do we have to run the "Add-A-Plotter Wizard" on all local machines before the standard PC3 file will work effectively? Or does having 2011 version still on the machines have an effect on these files?
Win 7 Pro 64-Bit - Dell T1600
Intel Xeon 3.30Ghz
8Gb RAM
Civil 3D 2013
I made an attempt at drawing out what I'm trying to say in MSPaint. At my office we use an HP Designjet 800ps to plot our drawings, most everyone uses AutoCAD 2010-2011 and I use AutoCAD LT 2010. All of our drawings are ANSI C size (17"x22") and we use paper rolls that are 24" wide x 150' long. For some reason our plotter always prints our drawings sideways causing us (read 'me, the assistant') to have to trim the excess off of every single print. Not only is this time consuming but it is a huge waste of paper! If I can get it to rotate we will get 19 MORE plots out of every roll of paper!!!
I was wondering if there is some way to change settings somewhere so that our drawings are printed the correct way, saving me lots of time and saving our company lots of paper? Is it normal to plot this way?
In AutoCAD for Architecture 2010 I am having problems publishing to a DWF (DWF6 ePlot.pc3) as well as to a PDF (DWG To PDF.pc3). On one machine everything works fine. On another machine it has worked but doesn't now.
I have tried the following:
Repaired AutoCAD for Architecture
Reinstalled AutoCAD for Architecture
Recreated both .pc3 files
Numerous reboots and restarts
The only difference is that the machine it doesn't work on has AutoCAD for Architecture 2009 installed. Both machines are XP64 SP2 with identical hardware.
2004 and how to turn "plot to file" off? Any time they go to plot the plot to file is already set and grayed out. It has been way too long since 2004 and I don't know where to have them look although I assume it is in Options somewhere.
View 2 Replies View RelatedI am plotting a file that has a pdf referenced into it. The quality of the plot is degraded only at the inserted pdf. The rest of the AutoCAD file looks fine. The inserted pdf is a printed AutoCAD file which looks clear and even has embedded layers and linework I can snap to (which seems to indicate that there is vector information present when it is in Autocad.
I have attached an image with 4 zoomed-in screen shots to show what I'm describing.
How to turn plot and publish log file off? (see attached pic)
I found out how to turn the one off under plot stamp settings, but I would like this box to be unchecked also and I want to do it automatically for all my users.
[URL]....
Civil3D 2014 SP1
Win 7 Professional - 64-bit
HP Z400
Xeon W3550 @ 3.07Ghz
24GB of RAM
Nvidia GeForce GTX 760
We just started in 2014 last week. When we batch plot to PDF using the DWG to PDF driver we get multi-page files no matter which is selected in the Publish Options. Any way to allow single sheet PDF creation?
View 9 Replies View RelatedI have both ACad 2002 and 2012, (both 32-bit) installed. I have plenty of RAM.
I'm converting a .dwg file to a .pdf and plotting to the desktop to either send out the pdf file or print to myself.
My problem is that it takes "what seems like forever" to plot a .pdf file to the desktop using 2012.
My situation is:
1. In 2002, using the Adobe pdf driver it takes 6.7 seconds from the time I press plot until the pdf file appears on my desktop.
2. In 2012, using the same 2000 formated file opened in 2012 it takes 37 seconds for the file to appear on my desktop.
3. In 2012, using a .pc3 driver, the same file, qsaved and formatted to 2012 takes 34 seconds to appear on the desktop.
Acrobat was installed on my computer prior to ACad 2012 but I've uninstalled/reinstalled Acrobat and I get the same result as above.
Is there anyway to speed Acrobat up? I defrag'd, cleaned the registry but I get the same results.
I have an HP Destjet 9650 printer and am using Acad 2005. I can generate aPLT file, but how do I print it?
View 7 Replies View RelatedI'm using autocad 2000 and I have a problem printing & plotting. The print, plot preview only shows a section of the drawing. What settings do I need to change for the entire drawing to print for the paper size I need.
View 3 Replies View RelatedWhenever I plot the 3d drawings in PDF or in our plotter, Some lines or some drawings are not shown in the printed layout. sample.jpg. try to check the red circle, there should be other stuff inside it. and in the second circle the one with the line should have a line itself, i just put some red lines to show in the drawing, but please try to check all.
View 3 Replies View RelatedI have one drawing per file at model tab. When I need to plot a multiple page file, I use:
Print > Batch Plot.
The problem is that I have to set plot configurations ( plot style table, plot area, paper size, etc) in each file before use Batch Plot.
Now I received 722 files with a wrong Plot Style Table. For this time I change the associated *.ctb file at Plot Style folder, but I will need to associate the right *.ctb to each drawing. It's also common to have to change other properties.
I am trying to set default plotter and plot style so I dont have to select every time but AutoCAD is not keeping the setting. I went to "Options", "Plot & Publish" and selected my plotter I want to be default but it's not keeping that setting. I also changed the default plot style under "Plot Style Table Settings" under "Plot & Publish" but AutoCAD is not keeping that setting as well. URL...
View 1 Replies View RelatedWhenever I create a PDF file the capital Ms and Ws get "spikey", if that makes sense. I use the simplex font primarily. I have C3D 2012, but this issue has been present back to LD 2009, and maybe farther. Only happens when I make PDFs, not other formats.
View 1 Replies View RelatedCould we can use 1 ctb file for all drawing scale? The problem is the lineweight at 1:100 is OK but at 1:5 it is quite light.
Could we use scale lineweght?
I am new to autocad, I downloaded autocad 2013, When I tried to print/plot it always blank(white), Is there any settings I need to for print/plot?
View 1 Replies View RelatedRecently upgrade to ACad 2012 from 2002 and have a Designjet 500 at my office and am having trougble with a dot hatch in .plt files being sent to my printshop.At my office, I'm using a Designjet.pc3 file for both the 2002 and 2012 dwg files and they plot identically, no problem.
In creating a .plt file using a 750c.pc3 file for both 2002 and 2012 files for my printshop, the plt file for 2002 plots fine but the plt file for 2012 omits the dot hatch. Other hatches on both drawing plot fine. In print preview in both ACads both files show the dot hatch. I'm using ABviewer to check the hatch problem so I don't have to keep bothering my printshop about this. With the 2002 plt file it looks fine but in the 2012 plt file the dot hatch is missing. ABviewer shows results consistant w/ my printshop.
Am using identical pc3 files and identical CTB files. This problem goes across all my drawings....all hatches work between 02 and 12 except the dot hatch. All drawings were qsaved into 2012 from 2002 when I ungraded cads.
I have created a new 750c.pc3 file and the problem is found in that as well.Attached are just small samples of the problem showing 2002 and 2012 examples.I can only believe I am missing a setting somewhere in 2012 or there is a problem between 2012 and the 750c print driver.
Any good chart I can have that prints a sample of all the pens?
View 6 Replies View Related