AutoCAD Print / Plot :: Print To Plotter Or Make PDF

Mar 8, 2011

I have a new machine with windows 7 64 bit and autocad 11. When I choose the 6204 as my plotter I get the following message : "This plotter configuration cannot be used for one of these reasons: the driver cannot be found, the device cannot be found, or the driver has a problem. The None plot device has been substituted." it does not matter if I choose to try and print to the plotter or make a PDF this error comes. up..

View 8 Replies


ADVERTISEMENT

AutoCAD Print / Plot :: Cannot Choose Plotter In Plot Manager

Jun 25, 2013

In AutoCAD 2014 and ASD2013 I cannot choose one of the printer, which is installed on Windows (OCE TDS600). It is strange, because Autocad sees it on the list of available plotters, but when I try to select it - it automaticly changes to "None".

The plotter is properly configured - I can print with it from Revit 2013 without any problems. Also when I switch account to any other (on that same computer) everything works fine.

I tried to add this plotter through "Add-A-Plotter Wizard", but each time I obtain an error massage "Autodesk Hardcopy component failed..."

[URL]

View 2 Replies View Related

AutoCAD Print / Plot :: Eliminating A Plotter

Jun 14, 2011

I recently stopped using my HP755 plotter and am now plotting "dwg to pdf". The problem is when I go to plot I get a warning message stating that "this plotter configuration cannot be used" and it goes on to list a few reasons why and selects the "none" plotter. Then when at the plot setup page I can continue to plot as I normally would. Why am I getting this warning and how do I stop it?

View 2 Replies View Related

AutoCAD Print / Plot :: Setting Up Old Hiplot Pen Plotter

Dec 6, 2000

I just got Autocad 2000i as an upgrade from 13 and 14. I have a summagraphics HiPlot 7200.It was set as a windows system printer on the old autocad versions, 2000i will not accept the widows driver (which works great on the old systems) and i have to use hpgl emulation wich sucks on 2000i

View 2 Replies View Related

AutoCAD Print / Plot :: How To Remove Some Of Plotter Names

Jan 2, 2003

We recently made the switch from R14 to 2000. In the LONG process of trying to figure out plotting in 2000, I ended up having a lot of plotter names to select from when I go to plot. We have 2 HP 450C plotters and 2 printers (HP5000N & HP 1220C) and I only have one pc3 file for each on the server. I want to nknow how to remove some of the plotter names from ACAD and have only the 2 plotters and 2 printers to choose from when you go to plot.

View 6 Replies View Related

AutoCAD Print / Plot :: Set Plotter To Cut Directly After Drawing

May 20, 2011

I was wondering if there is a way to set the plotter to cut directly after the drawing. i have changed the setting to extent but it still prints the whole page size.

View 9 Replies View Related

AutoCAD Print / Plot :: PDF File - Plotter Out Of Memory

Jul 30, 2012

I'm trying to plot a pdf file that is approx 1MB. We have a HP designjet 500 plus, with 32MB of Ram. When I try to plot it though, The plotter displays a messag: 'Out of memory. Data Lost'. I unfortunately only have the PDF file. Is there any way for me to plot this file?

I tried to print it as a pdf by using a virtual pdf printer, but the end result is the same. 

View 1 Replies View Related

AutoCAD Print / Plot :: Automatic Plotter Changing / Replacing

Mar 21, 2012

I need to change printer/plotter (maybe PC3 file) on my drawings. For example I have 'printerN.pc3' setted and I need to set 'PrinterM.pc3'. Also need to change print scale. But since I have many drawing I need somithing thatcan do iy automatically. So what I need:

I need to replace specific plotter to anither plotter:

1. For example if plotter setted to "HP" -> change to "Canon"

2. If paper size (2) is A3, set Plot scale (3) to 1:1.015, if Paper size (2) - A4, set Plot scale (3) to 1:1.02

Seems like I can do it with AutoLISP.

*** Using AutoCAD 2009 and 2011***

View 2 Replies View Related

AutoCAD Print / Plot :: DWG2PDF Plotter - Raster Compression

Jan 27, 2012

I have problem with AutoCAD DWG to PDF printer. When I use a vector drawing with a raster map attached and print the layout with the DWG to PDF printer, all the vector elements looks perfect in the output pdf file, but the raster image is almost unreadable. It doesn't work if I increase print resolution and it looks if there would be some kind of default jpeg compression inside this printer but there aren't any settings to control it or simply turn it off. After plotting such a drawing on the HP plotter it is so awful that there is no use of such a file.

View 9 Replies View Related

AutoCAD Print / Plot :: Shortcut In Plotter Search Invalid?

Nov 16, 2007

I get this message when I go to print in acad 2008.The following shortcuts in the plotter search were invalid and ignored: (invalid path is displayed here...) ending with .ink.The path exists and yet it says invalid and ignored. I hit OK and it continues to the plot dialog and everything works. How to correct the path or disable the dialog... I looked in the options/files(tab)/printer support file path and they are setup to our printers, but the error continues to pop up.

View 6 Replies View Related

AutoCAD Print / Plot :: Set Up Dummy Plotter To Generate PLT Files

Jan 17, 2012

I don't need the capability to print directly to a plotter, but I need to set up a dummy plotter to generate plt files that will be changed to tif files with our Kip. Any plotter driver that works for this situation? Every one I have tried has generated a plt file, but the Kip would not convert it or open it.

View 8 Replies View Related

AutoCAD Print / Plot :: Canon Plotter And Drawn Area Printing?

Dec 17, 2013

I have a question about plotting at Canon plotter (Canon imagePROGRAF iPF750) with possible has feature to plot as a drawn area.
 
Simply say I want to specified only one custom/roll paper size, make it custom size as a default. After that I want to plot exactly the accurate drawn area from my dwg. So with this settings I cannot specified custom paper size for each unique dwg.

For example I'm using this settings with another plotting device -- Xerox WF (picture to see the chosen settings) and working like a charm.

View 1 Replies View Related

AutoCAD Print / Plot :: Printing Is Always Wrong Rotated (HP Plotter DesignJet 500 Plus)

Apr 23, 2012

Although automatic rotating is on, the HP plotter DesignJet 500 plus uses the paper wasting method.

In the layout preview of Civil 3D 2012 the result looks good, but I need one meter of the paper roll for this plot.

View 2 Replies View Related

AutoCAD Print / Plot :: PC3 Files Not Working Properly / The Plotter Configuration Cannot Be Found

Nov 8, 2012

In the process of releasing 2013 to the office. We have about 60 machines being loaded, varying from 64-bit Win 7, 32-bit Win 7 and 32-bit Win XP. I have gone through and created new PC3 files for our two KIP printers (3000 & 7000 series). I added one custom page size to each to create a PMP that goes along with them. These files have been placed onto a network folder for all users to access. This is where my confusion begins.

When other users go to utilize these files it is giving an error stating that "the plotter configuration cannot be found, driver cannot be found, device cannot be found, yada yada. The none has been substituted."

So we began to look at the PC3 files and see what the issues are. When the same file on the Server is copied down to a local machine it changes back to a KIP10 driver down from a KIP11 driver on the network. Make Sense?

In order to fix I began running the "Add-A-Plotter Wizard" on the local machine. Created a new PC3 wiih a different name and went back into the program. Now the PC3's that did not work before WORK.

In short, since the 2013 version has a new file format do we have to run the "Add-A-Plotter Wizard" on all local machines before the standard PC3 file will work effectively? Or does having 2011 version still on the machines have an effect on these files?

Win 7 Pro 64-Bit - Dell T1600
Intel Xeon 3.30Ghz
8Gb RAM
Civil 3D 2013

View 1 Replies View Related

AutoCAD Print / Plot :: Plotter Prints DWGs Sideways - Wastes Paper

Oct 24, 2012

I made an attempt at drawing out what I'm trying to say in MSPaint. At my office we use an HP Designjet 800ps to plot our drawings, most everyone uses AutoCAD 2010-2011 and I use AutoCAD LT 2010. All of our drawings are ANSI C size (17"x22") and we use paper rolls that are 24" wide x 150' long. For some reason our plotter always prints our drawings sideways causing us (read 'me, the assistant') to have to trim the excess off of every single print. Not only is this time consuming but it is a huge waste of paper! If I can get it to rotate we will get 19 MORE plots out of every roll of paper!!!

I was wondering if there is some way to change settings somewhere so that our drawings are printed the correct way, saving me lots of time and saving our company lots of paper? Is it normal to plot this way?

View 1 Replies View Related

AutoCAD Print / Plot :: Print / Plot Preview Shows Section Of Drawing

Jan 20, 2012

I'm using autocad 2000 and I have a problem printing & plotting.  The print, plot preview only shows a section of the drawing. What settings do I need to change for the entire drawing to print for the paper size I need.

View 3 Replies View Related

AutoCAD Print / Plot :: Printing In 3D - Some Solid Items Print With Wire Frame

Jan 12, 2011

When printing in 3d with the vp set to 3dhidden and the shade plot set to hidden legacy some solid items print with the wire frame.  This usualy happens with torus and cones.  How do I stop this?

In the example look at the U-bolt.

View 2 Replies View Related

AutoCAD Print / Plot :: Can't Print To HP Designjet T770 From 2012 On Windows 7 Machine

Oct 14, 2011

I am having trouble printing to an HP Designjet T770 from AutoCad LT 2012, on a Windows 7 computer.

I am using the HPGL/2 driver. I can print a test page, and I can print from other programs.

When I try to print, it looks like it is sending it normally, but the printer just ignores it.

I am able to print to this printer from AutoCad 2010 on a Vista computer.

View 8 Replies View Related

AutoCAD Print / Plot :: How To Print Multiple Layout Pages In A Printer

Oct 14, 2012

I have multiple layout pages (58 pages) and would like to print them in a printer at once. How do I do that?

Currently, I open 1 layout at a time then print it 1 by 1, in which its killing me specially if I do have lots of drawings.

Publish does saving in DWF, PDF... But does not print in the printer.

View 3 Replies View Related

AutoCAD Print / Plot :: DWG To PDF Batch Print To Single Sheet File

Sep 30, 2013

We just started in 2014 last week.  When we batch plot to PDF using the DWG to PDF driver we get multi-page files no matter which is selected in the Publish Options. Any way to allow single sheet PDF creation?

View 9 Replies View Related

AutoCAD Print / Plot :: Screened Lines In PDF Print Blue / Purple?

Jul 14, 2011

I have a drawing where some lines have a 60% screening in there Plot Style.  The print great from AutoCAD.  But when I create a PDF and then print the PDF the Screened lines show up kind of blue / purple.

I am plotting to a Cannon iPF720 on 22x34 paper from Acrobat Reader X.  I'm creating the PDF from AutoCAD 2012.

View 1 Replies View Related

AutoCAD Print / Plot :: Fatal Error When Print To Acrobat Converter

Nov 16, 2011

I get "Fatal Error: Unhandled c000000dh Exception at 24079af3h" every time when I print to pdf with Acrobat 9 in AutoCAD 2012. However, the Acrobat converter is working properly in other applications. It only happens in ACad 2012.

View 1 Replies View Related

AutoCAD Print / Plot :: Same Line Weights On Different Layers Print Out At Different Scales?

Aug 1, 2013

I have two layers. One is set to red color, the other to blue color (using ctb). I have both layers defaulted to 1 mm line weight thickness. Blue is continuous and Red is dashed. 

When printing the blue layer prints at the correct weight of 1mm, while the dashed red layer prints at a much smaller thickness. All line properties are set to default or bylayer (this is not being caused by the lines having individual special properties).

View 3 Replies View Related

AutoCAD Print / Plot :: Cannot Print Imported Images - Large Bitmap

Sep 7, 2012

I work in AutoCAD 2010.

(AMD 64 X2 4200+, 2Gb RAM, C: 7Gb free, D: 17 Gb free)

I can not print imported images (JPG or TIFF) large size 80 - 260 Mb.

Print all but the raster! I tried to print on a plotter in JPG, TIFF, in whole or in parts, useless.

If I export the whole project in JPG 2000x3000 pix, all right, but I have 9000x10000 pixels - that size is not exported.

View 1 Replies View Related

AutoCAD Print / Plot :: Randomly Get Fatal Error Every 10 To 15 Drawings That Print?

Aug 23, 2011

When I am printing from AutoCAD LT 2012, I randomly get this error message every 10 to 15 drawings that I print. Considering that I print 10-15 drawings at one time, I am getting a fatal error every time I print a set. Why? I don't get this error when printing in AutoCAD 2011LT or 2012 Full Version.

View 1 Replies View Related

AutoCAD Print / Plot :: Xref Title Block Will Not Print In Color Windows 7 64bit

Feb 3, 2012

I'm having an issue with Autocad LT 2010 where when I xref in my title block which has our company logo in color, the logo will only print in black and white.  If i open just the title block and print it, it will then print in color.  I only seem to have this problem when the title block is xref'd in.  I downloaded the 2012 demo version of AutoCadLT and it prints just fine?This has just started happening when my computer was upgraded to Windows 7 64 bit.

View 8 Replies View Related

AutoCAD Print / Plot :: Acrobat Standard X Processing Very Slowly To Print Desktop File

Jul 4, 2011

I have both ACad 2002 and 2012, (both 32-bit) installed. I have plenty of RAM.

I'm converting a .dwg file to a .pdf and plotting to the desktop to either send out the pdf file or print to myself.

My problem is that it takes "what seems like forever" to plot a .pdf file to the desktop using 2012.

My situation is:

1. In 2002, using the Adobe pdf driver it takes 6.7 seconds from the time I press plot until the pdf file appears on my desktop.

2. In 2012, using the same 2000 formated file opened in 2012 it takes 37 seconds for the file to appear on my desktop.

3. In 2012, using a .pc3 driver, the same file, qsaved and formatted to 2012 takes 34 seconds to appear on the desktop.

Acrobat was installed on my computer prior to ACad 2012 but I've uninstalled/reinstalled Acrobat and I get the same result as above.

Is there anyway to speed Acrobat up? I defrag'd, cleaned the registry but I get the same results.

View 9 Replies View Related

AutoCAD Print / Plot :: Change Print Limits Of A Layout

Sep 12, 2012

I’ve done it before in the past so I know its possible but I have forgotten how. See the attached image I would like to change the printable area of my paper space layout.

View 5 Replies View Related

AutoCAD Print / Plot :: Print Preview Thick Lines?

Jan 8, 2014

I received an Autocad file from another person, opened it with Autocad 2011 LT, and it looks fine. But when I go to print preview all the lines are very thick, making the detail of the drawing difficult to see. I've tried manually changing the lineweights but it has no effect on some of the layers. Is there an easier way to fix this other than recreating layers?

View 1 Replies View Related

AutoCAD Print / Plot :: Can't Print Something In Real World Inches

Aug 3, 2013

im trying to make a simple rectangle thats 9" long and 1/2 " high. and when i set it up in autocad it will not print out that size not sure if im doing something wrong in the units settings or in the plot. farly new to the auto cad program 

View 4 Replies View Related

AutoCAD Print / Plot :: Fill Hatch Won't Print As Solid

Jan 10, 2014

I am trying to create logo's as blocks to insert into title blocks efficiently. I made the outline of the first logo and hatched it as a solid hoping it would print as a flat black but it is showing up as streaky, almost as if I used a different hatch at an extremely small scale. I don't think it is a printer issue because even when printed to .pdf format it still shows up as streaky.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved