I am having trouble printing to an HP Designjet T770 from AutoCad LT 2012, on a Windows 7 computer.
I am using the HPGL/2 driver. I can print a test page, and I can print from other programs.
When I try to print, it looks like it is sending it normally, but the printer just ignores it.
I am able to print to this printer from AutoCad 2010 on a Vista computer.
I have a template with layouts of different sizes that had been working fine with a previous Xerox 6204. My D size and E size automatically oriented with the 36" side parallel to the roll feed. I have since moved to a job that got a Designjet T2300. On this machine the D size orients the 24" side parallel. This wastes 1' of paper on the left and uses 1' extra as it runs the 36" side perpendicular. I have been unable to rectify the problem. I have tried printing in portrait, that actually cut off some of the image. I have tried all types of rotation within the driver and layouts. Tech support had me going into the machine settings and set rotation to 90. Nothing. There is a warning that "HP utilities" is not installed. Could this be a remedy? When the tech came to set up the printer he installed the necessary drivers but mad no mention of this utility.
AC2012, HP desighjet T2300
Looks like the format is not forwarded correctly to the printer when printing A3, it comes out as A4. If we change paper format in printer properties to A3 it works fine.
View 3 Replies View RelatedI am trying to plot a layout sheet 24'' W x 18" H. The frame on my sheet is 22''W x 16''L (inside the dash lines limits we see on the layout). I believe I prepare the print correctly:
- Select the printer (HP DESIGN JET PS)
- I use the window fonction to select the printable area ( left upper corner and then the opposite corner).
- Select Paper size Arch C (landscape)
- Paper orientation: Lansdcape
The preview shows that the upper and bottom lines of my frame will not print, and they do not, even if I try (see the attachement below).
Is this a driver problem?
I have a problem with print from Autodesk Mechanical on a HP Designjet 500 24.
The system is a Windows 7 Professional 64bit.
When I select the printer, the printer returns to "none".
I have tried several drivers, the HP Designjet 500 plus 24 or HP DesignJet 500 24+HPGL2 card.
I can select the HP DesignJet 500 24+HPGL2 card, but since that driver is incorrect for my printer, it doesn't print.
I have found this same problem for a HP Designjet T610.
Here is says to use a driver version from 10 feb 2010 or later. But there isn't any driver around or after this date for the HP Designjet 500.
Other program's can print just fine through the original HP Designjet 500 24 driver.
Client machines are windows7 64bit sp1.Having issues with one plotter at this point-- HP DesignJet T1200 HD MFP.
.This plotter worked fine with AutoCAD 2013 Autodesk software uses windows printer objects for printing not pc3s.
Plotter driver is the newest hpgl2 off hp's website for that plotter.
So far crashes when attempting to plot from autocad and revit. Gets the attached message.
Although automatic rotating is on, the HP plotter DesignJet 500 plus uses the paper wasting method.
In the layout preview of Civil 3D 2012 the result looks good, but I need one meter of the paper roll for this plot.
Printing pdf's to an HP Designjet 1055 using the new Acrobat X version. I can't change the page size from 8.5x11and nothing comes out at the 1055. Works fine to our Xerox 6204 printers. Looks like I could be going back to Acrobat 9.4...
View 3 Replies View RelatedCan users with a 64 bit computer share pc3's and pmp's with 32 bit users without adverse effects?
View 1 Replies View RelatedI'm having an issue with Autocad LT 2010 where when I xref in my title block which has our company logo in color, the logo will only print in black and white. If i open just the title block and print it, it will then print in color. I only seem to have this problem when the title block is xref'd in. I downloaded the 2012 demo version of AutoCadLT and it prints just fine?This has just started happening when my computer was upgraded to Windows 7 64 bit.
View 8 Replies View RelatedI recently upgraded from 2010 to 2012 and when trying to plot, using the very same page setups as before the upgrade, the quality (or resolution) of the plot is very poor and pixelated. I am using very high resolution aerial imagery. The output is not at all high resolution (totally pixelated, not presentable as professional). It seems like AutoCAD is reducing the image quality now. Is this a system variable that can be adjusted?
View 1 Replies View RelatedI'm using autocad 2000 and I have a problem printing & plotting. The print, plot preview only shows a section of the drawing. What settings do I need to change for the entire drawing to print for the paper size I need.
View 3 Replies View RelatedI have all of our .pc3 files on a server, and have created them in the order I would like to see them, however they come in a random order. I have moved them out of the folder, and back in the order I want with no luck. I tried renaming them with numbers in front, and then with letters in front to try and populate the list in a certain order. I only have 16 .pc3 files and MAXSORT is default at 6000.
We are using page setups as well which are not a problem, but the occasional time we need to print to a specific .pc3 file gets annoying having to sort through the list to find the one we want.
Just installed 2012 from 2000. Plot style table (file copied from old installation) has all colors set to grayscale=off but is printing with grayscale.
View 9 Replies View RelatedTwo of our computers have windows 7 and we are unable to publish or if we plot we have to wait until that page is completed before sending another page otherwise only some the information shows up when printed (ie. no dimensions or no title block). This does not happen on the other computer in the office which still has windows XP.
View 2 Replies View Relatedi used the page setup and creat new setup to print some area ..
ist possible to make a setup to print multi area .. - when i creat new one it ask to select what i want to print , but it just ask once ,if i want to print other thing i need to creat new setup ...
what i need is to selcect multi time .
Before upgrading to 2012 from 2010 (against our will), our publishing tool worked seamlessly with our XEROX 6604. Now, strangely only one user out of seven has the ability to publish a set of drawings without crashing AutoCAD. We are happy that it works on his machine, but it seems very odd that the rest of us are affected when our PCs are the same spec and setup.
All of the proper drivers and firmware are up to date.
On PC_71, While ploting(creating the pdf via autocad) the pdf,its everytime coming in portait format but we want in landscape format.
On PC_71, if we create the pdf of any document by our Adobe pdf printer PRT13 then its creating pdf properly for both portait and landscape format . But for any autocad drawing file , the pdf printer PRT13 is not creating in landscape format.
I also cross-checked all plot setting with other proper working PC , its same then also its behave differently.
And if we create pdf on any other PC then its creating the pdf properly for any drawing but not on PC_71.
Also 1 more typical point I noticed that if we delete any pdf file from PC_71, then after refreshing its again appeared on same location.
Note - We are using:
Software : Autocad 2012-64Bit , Naviswork 2013 , Inventor Ultimate 2014-64 Bit , Bentley Autoplant V8i - SS4 version : 8.11.9.140 ,MS-Office 2010 - 64 Bit.
Hardware : Workstation Dell Precision T3600
Copied the printer configuration (pc3 and pmp) from AutoCAD 2013 to AutoCAD 2012. Plot the same drawing with that same printer configuration. With AutoCAD 2013, it plots out fine - page orientation landscape. In 2012, it plots out wrong. The orientation of the drawing is correct, but the paper is changed to portrait?
The plot setting are exactly the same in both versions.
Coworker is setting up a new Win7 (64bit) machine but we don't have the ability to upgrade CAD at this time. So running AutoCAD Mechanical 2007. (Yes we know they don't always play nice) Two other workstations here are running the same OS & CAD and print without issues. This new machine AutoCAD does not see any system printers. Have made sure the "Hide System Printers" is not checked under options. I can add a plotter file for each system printer and that workaround is OK, but why this one machine can't see the system printers. They are Xerox workstations on the network - not local. We have already restarted AutoCAD and restarted the PC.
View 3 Replies View RelatedI am facing this problem that when i give plot command and preview the window it show fonts different other than my main window. Also it prints as per the preview window and not as per the fonts present in my AutoCAD model space and layout.
View 1 Replies View RelatedWhen printing in 3d with the vp set to 3dhidden and the shade plot set to hidden legacy some solid items print with the wire frame. This usualy happens with torus and cones. How do I stop this?
In the example look at the U-bolt.
I have multiple layout pages (58 pages) and would like to print them in a printer at once. How do I do that?
Currently, I open 1 layout at a time then print it 1 by 1, in which its killing me specially if I do have lots of drawings.
Publish does saving in DWF, PDF... But does not print in the printer.
We just started in 2014 last week. When we batch plot to PDF using the DWG to PDF driver we get multi-page files no matter which is selected in the Publish Options. Any way to allow single sheet PDF creation?
View 9 Replies View RelatedI have a drawing where some lines have a 60% screening in there Plot Style. The print great from AutoCAD. But when I create a PDF and then print the PDF the Screened lines show up kind of blue / purple.
I am plotting to a Cannon iPF720 on 22x34 paper from Acrobat Reader X. I'm creating the PDF from AutoCAD 2012.
I get "Fatal Error: Unhandled c000000dh Exception at 24079af3h" every time when I print to pdf with Acrobat 9 in AutoCAD 2012. However, the Acrobat converter is working properly in other applications. It only happens in ACad 2012.
View 1 Replies View RelatedI have two layers. One is set to red color, the other to blue color (using ctb). I have both layers defaulted to 1 mm line weight thickness. Blue is continuous and Red is dashed.
When printing the blue layer prints at the correct weight of 1mm, while the dashed red layer prints at a much smaller thickness. All line properties are set to default or bylayer (this is not being caused by the lines having individual special properties).
I work in AutoCAD 2010.
(AMD 64 X2 4200+, 2Gb RAM, C: 7Gb free, D: 17 Gb free)
I can not print imported images (JPG or TIFF) large size 80 - 260 Mb.
Print all but the raster! I tried to print on a plotter in JPG, TIFF, in whole or in parts, useless.
If I export the whole project in JPG 2000x3000 pix, all right, but I have 9000x10000 pixels - that size is not exported.
When I am printing from AutoCAD LT 2012, I randomly get this error message every 10 to 15 drawings that I print. Considering that I print 10-15 drawings at one time, I am getting a fatal error every time I print a set. Why? I don't get this error when printing in AutoCAD 2011LT or 2012 Full Version.
View 1 Replies View RelatedI have both ACad 2002 and 2012, (both 32-bit) installed. I have plenty of RAM.
I'm converting a .dwg file to a .pdf and plotting to the desktop to either send out the pdf file or print to myself.
My problem is that it takes "what seems like forever" to plot a .pdf file to the desktop using 2012.
My situation is:
1. In 2002, using the Adobe pdf driver it takes 6.7 seconds from the time I press plot until the pdf file appears on my desktop.
2. In 2012, using the same 2000 formated file opened in 2012 it takes 37 seconds for the file to appear on my desktop.
3. In 2012, using a .pc3 driver, the same file, qsaved and formatted to 2012 takes 34 seconds to appear on the desktop.
Acrobat was installed on my computer prior to ACad 2012 but I've uninstalled/reinstalled Acrobat and I get the same result as above.
Is there anyway to speed Acrobat up? I defrag'd, cleaned the registry but I get the same results.
I’ve done it before in the past so I know its possible but I have forgotten how. See the attached image I would like to change the printable area of my paper space layout.
View 5 Replies View Related
