I'm using Autocad LT 2012. If I draw in an isometric view, is there a way to look at each direction to see the different views? For instance if I make a cube, can I hatch all six sides with different colors to show if I'm looking at the correct view?
View 7 Replies
I need to check if all my three views are correct.
I attached the dwg
How do I annotate the views?
We have been putting dimensions on isometric views and the dimensions have been coming out fine. Now, however, we have an isometric and the dimension is about 400mm out and is not on the plane/face it should be.
View 5 Replies View RelatedI have an assembly that I would like to show dimensions on an isometric view. I am able to create the dimension, no problem. Issue I'm having is that when placed on a standard lettersize page, the dimensions are too hard to read. I've tried editing the size by double clicking the dimension & editing the font. It doesn't seem to make a difference what font size I enter, the size remains the same. How can I change the text size on isometric dimensions?
View 2 Replies View RelatedI am trying to create an automatic isometric drawing from the top, side and front views...
View 9 Replies View RelatedWhen I start an Iso drawing should I use the 3D Views under the View tab and set it to SW Isometric or should I use the Snap/Style/Isometric way? I like using the 3D views, but it doesnt set the drawing up the same. What is the accepted procedure.
View 7 Replies View Relatedon a couple of my lager project i have recently had issues with Autodesk Civil 3D 2012 Freezing in Model Space switching between Isometric views. the number of view changes varies each time but seams to freeze during regen of the model.
I have checked the performace tuner and updated my driver, see Attached Log.
We are in the process of changing our CAD Stations over to Windows 7 64 bit, but im not scheduled for a couple more months.
System:
Dell Precision T3400
Windows XP SP3 32 bit
Intel Core2 Quad (Q9550 @ 2.53GHz)
4GB RAM
I have not done much isometric work for quite a few years now but i have a new company i am doing some freelance stuff for and the last in house person did all his drawings as isometrics. My problem is not working in isometric but when I switch to paper space..how do I convert those isometric drawings to regular 2d?...this might be basic stuff for some but like I said I haven't done this in quite some time.
They are using AutoCadLT 2005 & Building systems MEP...I usually use AutoCad 2000 at home.
I have been asked by one of my clients to provide an isometric piping diagram for a product that we have modeled/developed for them. We have already provided models, review drawings, design drawings, and fabrication drawings for this product but what they are looking for is a simple isometric pipe diagram where they can hand write their weld test data and put the material data sheet number references. I have submitted a sample of a drawing we completed with an isometric view of this piping as a full view (iso view created by IV) but they are requesting something simpler like they are used to (one-line iso pipe spool-type thing with symbols instead of modeled valves, etc.). I am embarking on a process to get them to change their standard but I was wondering what you experts thought while I am doing this (in case they refuse).
I don't want to create drawing that isn't tied to the model somehow for obvious future-revisions-parametric reasons so I was wondering what you think my options would be for keeping this all in IV (instead of just doing something seperate in AutoCAD.
Inventor Professional 2013 (SP-2.3), Product Design Suite Ultimate
Desktop: Intel Core i7 3.4GHz, 16.0 GB RAM, Windows 7 Ultimate SP-1, 64-bit OS, (2) GeForce GTX 580 (331.81), Space Pilot Pro (3.16.1)
Laptop: Intel Core i7 3.9GHz, 16.0 GB RAM, Windows 7 Pro SP-1, 64-bit OS, GeForce GTX 780 (331.81), SpaceNavigator (3.17.7)
I've been running into issues in IV 2010 with the shading where I need to show a part in a perspective view on my IDWs and depending on the angle I rotate to the majority of the part is shown in shadow. It's frustrating because I need to show a feature in that particular orientation, but the whole part looks dark.
Especially when I am showing left and right mirrored parts. One side always seems to end up dark. FYI I almost never show the material as a texture map in my part drawings so I use white as the color default because I am simply trying to get across the shape of the part in a shaded 3D view. These don't really serve as renderings to me per say. Is there any way to control the light source direction for custom views in terms of shading? Could I make it more of an ambient light or similar to the Global Light Style in Inventor Studio.
If it is possible to create proper dimensions for 3D isometric drafting views? In AutoCAD I could set an oblique angle for a dimension but in Revit there is no setting. I can only dimension 3D model views.
See attached PDF for example.
Any way to move objects in vertical direction (z-axis) in 3d views, without having to turn the view everytime to be of frontal direction. I would like to move entire objects - for example mass objects - up or down directly in a 3d view of random orientation, now only top- or bottom face can be moved vertically, the whole object moves only on xy -plane. Can vertical movement of an object be done intuitively graphically and/or can it be be numerically, feeding coordinates?
Have tried all sources, but cannot find solution, and refuse to believe that Revit would be the only 3d/bim software on planet where direct vertical manipulation of objects is not possible.
I'm working on a drawing that has some plan views that I need to keep.. but I would like to import views from another drawing.
Is there a way to copy views from another drawing? Would be nice if when you insert another drawing as a block, it would bring the views along, same way that it brings along blocks, layers, linetypes.. etc.
[URL]
I need to put my 3d model on a piece of paper, so I need to have annotate and different views (FRONT and/or TOP and/or Right) of the model.
I tried to use FLATSPOT command, but all annotations (dimensions) are gone. Also, is there any easy way to do annotations?
How you constrain a section view so that is perpendicular to an axis. See "SECTION B" on the attached drawing for an example of what I am attempting. I have created the view but cannot make (constrain) the view perpendicular to the slot that is orientated at 30 degrees from the vertical centre line. I have lined up the view by eye so it looks close but it's obviously it's not accurate.
Product Design Suite
Inventor Premium 2012 - SP1 Installed
HP 8760w I7-740M Laptop
Windows 7 Professional 64
12 Gb DDR SDRAM
AMD FirePro M5950 Graphics Card
Been using Inventor from day one, never had a problem turning off the visibility of parts in darwing views till now.I cant hide parts in IDWs anymore.
* Select set to "Part Priority"... right click on a line in a drawing view... and "Visiblity" is grayed out.
* Browser Bar... find view of assembly, right click on a part.... and "Visiblity" is grayed out.
I wanted to create an isometric text in isometric view to indicate different names in different part.
Attached is the picture for reference.I did it using dimension, check the "hide dimension" option.But i can't hide the extension line.
how to create an isometric text?
I have created a linetype with the text GAS OPTION in it. The line is continuous with a break around the text. In a straight line the linetype works fine (breaks around the text etc). However, when I use a polyline and spline the line for a curved line the text aligns with the direction of the line at the start, but when the line bends, the text suddenly changes direction and reads in the opposite direction. It looks like AutoCAD is trying to keep the text upright rather than following the direction of the line. When the text changes direction it also changes its insertion point and overlaps the continuous part of the line. I have 2013 AutoCAD.
Here is the string I used for the linetype.
*GAS_Option_LINE,Gas line ----GAS OPTION----GAS OPTION----GAS OPTION----
A,8,-15,["GAS OPTION",STANDARD,S=2.54,U=0.0,X=-2.35,Y=-1.27],-12
I have cut several sections at different points along a road alignment. The sections are cut facing the same direction as the alignmnet. Is there a way to reverse the section direction without changing the alignment direction?
View 6 Replies View RelatedI have a drawing of a stone railing section and I have to change direction in the run direction of the baluster panel. Is there a way that I can move the details without changing th Y direction of the details. Please refer to the attached CAD file for details. I am trying to avoid having to redesign the panels if possible. railing detail.dwg
View 6 Replies View RelatedI have a path with a smooth point. The two direction points form a direction line with any non-45-degree-angle - say 11.8 degrees. I want to drag one direction point while keeping the angle of exactly 11.8 degrees.
Is there a key combination for that (Mac OS)?
I am trying to create a second base view (using Layout/Create View/Base from model space). The problem is, I need it to be rotated from the original base view. However, when I rotate the part in model space, ALL of my views change.
So I guess my question is, how do I create multiple views of the same part that are seperate from the other base views?
i have views lets say 3 views on a sheet but in the list of views theres mores that appears maybe i inserted the extra views that are showing but i deleted them to put them on another sheet
the problem is they show up in the list of both sheet and i can't delete them from the list of the sheet that they were before
We would like to make the transparency of glass-materials visible in views and section-views by using the "realistic style". During a 3d-view our glass-material looks like transparent. Isn't it possible for REVIT to display the transparency of materials in views ?
The workaround to hide "glass" by using "overriding visibility" is not possible for us because some of our families and project families are using glass-materials inside (Showcases f.e.).
Software (German) :
RAC 2012+2013
Inventor Pro 2013
AcadM 2012
MaxDesign 2013
Sketchup 8 Pro
Since the end of Aug. 2012 I've been making families for a manufacturer. I left Friday evening with good families. This morning I am finding all the families I checked with a problem.
When I move the cursor across the various views it doubles the views. Rolling the mouse wheel one click either way to zoom in or out cleans the view but on the next time the cursor goes across the view it doubles it again. Now there are 4 views overlapping each other. The next time it is possibly 8, and so on. It is difficult to count them because they are overlapping but it looks like they are doubling each time.
The software is Revit Architecture 2011 and the computer is a Dell Precision T3500.Are the families corrupted or is it the computer? Is there a toggle I hit that I shouldn't have?
I'm using ACAD LT 2008.
When i try to copy paste some drawing entities from a heavy drawing file to any other file, the program blocks and says 'not responding', endlessly. So i always have to shutdown the program. I experience the same problem using the designcenter: when I try to copy a layout into another drawing, my computer gets stuck.
Another annoying problem with these files is that they are so heavy, while in fact they shouldn't be. I tried the aectoacad file command. In result the file id half as big, but after I open it and save it, again is the original size.
Every now and then I go back and try to use publish to speed up printing but I always go back to plotting one by one.
I work in a housing construction office and I have 10 separate drawings side by side in model space for house plans that I need plot separate to give to certain people. My problem isn't that I can't publish them separately its that I can't save them over existing pdf's individually predetermined.
Q1. do i just have to go through and change every layout name before or after i publish?
Q2. how do i change the output publish location?
Q3. can each layout be saved to a different existing pdf and remember it?
Q3. can i save these setting across to a new drawing?
I'm currently taking an CAD program and I'm having trouble drawing a few objects in isometric perspective. These objects must unfortunately be drawn in 2D. I've drawn the orthographic perspectives for each object based on the dimensioning given however I'm unsure how to proceed on certain portions of the drawing. This is all homework and I doubt using any customization is allowed.
The first image is a top view of a fixture. I'm having trouble with the central portion which I draw by first constructing the vertical arm then using the array command.
Is there some way to create an array of this object that respects the isoplane that I drew my isocircles in?
If not, I'm able to look at the original using the VPOINT from the 1,-1,1 point and get the perspective that I want. Is there a way to use the UCS and trace over the orthographic perspective then take that traced image back to the world X-Y plane? I've tried this before but once I get it back it simply looks like the orthographic perspective.
The following drawing I'm simply having trouble drawing one particular curve which the green arrow points to. The drawing is of two perpendicular intersecting cylinders one having a slightly smaller radius then the other and the curve in question represents the edge formed by the intersection. The research I've done indicates that it's an ellipse however I'm unsure how to draw it correctly and the one I put in is simply an estimate. How can I construct the correct curve? Even if I could change viewpoints I'm not sure I could find a way to trace this one.
How to draw 2D isometric images from orthographic projections in AutoCAD as it seems many of the sites I find are either trivial or focus on drawing by hand.
I have a 3D model, only poly-lines, i would like to turn it into a 2D isometric drawing (model space). Something similar to flatshot would do the trick. (flatshot works only on surfaces and solids...)
View 3 Replies View Relatedhow to chamfer an isometric box. I need to do the 2 front edges but unsure.
View 9 Replies View RelatedIm new to CADTutor, and fairly new to AutoCAD. I used to use Plant 3D which has the ability to create PCF's and Isometric drawings, but Im now using MEP. for the most part, a better solution for our company, but now we cant create isomtric shop drawings. AutoCAD now has Isometric WS CLoud. how we can create a PCF file from an AutoCAD MEP 2013 drawing? its seems rediculous that it cant?
it seems like Isometric WS is real loser if you can only use with Plant 3D
