Software: ACAD LT 2010. Recently I upgraded to a new computer and Windows 7, from Win XP. Now ACAD is lagging and dragging. Also, sometime it takes forever to open a file.
Here are my new computer specs.
Dell Precision T3600,MT,425W
Four Core XEON E5-1607, 3.0GHz, 10M, Dell Precision T3600
Specs:
Autocad Civil 3D 2011 (64 bit)
AMD Athlon(tm) 64 FX-62 Dual Core Processor
NVIDIA GeForce GTX 260 (Graphics Card)
8 gigs of DDR2 ram
Dual monitors
Windows 7 64 bit
The cursor (crosshair / mouse) flickers constantly when I am moving the mouse around inside the autocad work space. If I draw a line the flickering gets even worse and it starts to lag slightly. The computer meets all of the recommended requirements as far as I am aware.
The CPU never goes above 45% usage and the RAM never goes past 21% usage. So the computer does not seem to be overloaded especially just trying to draw a line. All the drivers are up-to-date. Is it possible there is some sort of compatibility issue going on here or something I am overlooking?
When I go to draw a polyline, it feels like the snap mode is on and it takes forever to select my end point. It's almost as if it is lagging behind. I did not see this problem until I upgraded to 2012 last week. Going back to 2011, it seems to be doing the same thing.
View 8 Replies View RelatedYesterday (3/20/12) AutoCAD started lagging really bad when starting or ending certain commands (like "line") and I tried various things that didn't work first and then looked to see if I had gotten a recent windows update. Sure enough there was one right before the problems started. I did a system restore back to an earlier time and it fixed it right up. I actually had to restore back to 3/13/12 because for some reason it didn't want to restore to 3/15/12.
View 1 Replies View RelatedI have a ListView control from where I drag items to Drawing area. Whenever mouse leaves the ListView Control and enters the AutoCAD drawing area, AutoCAD claims the mouse cursor back to Cross Pointer.
Is it possible to change this cursor during drag operation to a pointer with some attachment? As normally happened in Windows Explorer while dragging and dropping files among folders.
Why does dragging on a Touch Screen change the cursor into a Hand Tool? This did not happen in CS 5.5 and I could edit on my touch screen monitor. With Photoshop CS 6, as soon as I start to drag, the cursor changes to a hand cursor. I have look at all of the system options and nothing seems to affect it so I have to assume it is something wrong with Photoshop CS 6.
View 3 Replies View RelatedI bought a new laptop Asus k73SV-TY081V version. When i'm working with autoCAD 2012, my videocard crashes and i get a message: "Display driver Intel Graphics Accelerator Drivers for Windows 7® stopped responding and has successfully recovered"
View 9 Replies View RelatedI've just performed a clean install of Lion on my MBP 2.4Ghz Mid 2010 with 8GB RAM running Photoshop 12.0.4 and lag when dragging or resizing windows. It's the only app running and I'm testing on any size file i.e. one that's blank and just bee created.
I've done the following:
- Restarted the Mac
- Repaired the d
how to draw 3d box in Dragging Using object arx.
View 2 Replies View RelatedMy cursor is very sluggish in AutoCAD 2010, works fine in 2009.
Is there a setting for the cursor speed or resolution that I'm missing?
My machine is Intel Core 2 Duo E6300, 1.86Ghz, with 3GB RAM,
Intel(R) 946GZ Express Chipset Family [Display adapter] on board video,
Windows XP Professional Service Pack 3, 32bit.
After an AutoCAD/Windows crash, I reboot. The system begins to load Windows (Win 7 splash), then the screen goes blank and a white Windows cursor appears -- nothing more; no desktop or taskbar.
Control-Alt-Del does nothing, however, the HDD light continues to flash as if it is continuing to boot. The same thing happens when I boot in Safe Mode (except cursor is larger due to different resolution).
I can boot from bootable CD and everything works fine. HDD scan and memtest both pass. I formatted the drive and reinstalled Windows and AutoCAD and everything works fine. However, two days later, the same exact problem occurred on the second of five workstations.
Details:
Win 7 Professional 64bit
MS Office Home and Business (with Outlook configured for IMAP)
i7 processor, 6GB ECC RAM, Nvidia Quadro 600 w/1GB RAM.
AutoCAD 2013 was originally loaded from a trial version, then purchased license key installed.We are using Xref on a file server and opening drawing on a file server across a ethernet Gbit lan.
I'm refining some SVG files, imported into GIMP as paths. I added numerous guides on the images and drag anchors to the guides. All the paths consist of straight lines only. The problem is that on some anchors GIMP performs the "drag curve" operation instead of the "drag anchor". As a result, my straight lines become broken (curved).
The only solution I've found so far is to apply maximum zoom level, say 400%, and repeat the dragging in this resolution. This makes GIMP work properly, at least, I'm able to "drag anchor" as expected. But switching back and forth to the 400% zoom level is a bit annoying and inconvenient.
Is there a better way to "say" GIMP that "dragging anchor" is the "dragging anchor", not "dragging curve"?
While making selection by drawing a selection window, the objects often get seelected and get dragged. These objects lie on the starting vertex of the selection window. Therefore I have to find the desired bjects to be selected in object manager lying in haphazard order. Is there a way , the objects don’t get dragged while making a selection window from left to right. That means, the objects get selected which are present in the selection window only.
Windows 7 [64-bit], Core i3 - 3.02 GHz, 4GB DDR 3 RAM
is this possible. A lot of programs auto-duplicate when you drag and press either the shift or ctrl or alt key. Its a habit ive gotten pretty into. Plus, its a little akward for me to go from a left click immeadeitaly into a right click with the mouse. I always feel like i've dragged the object a little bit when I switch fingers. it would be great to just add a hot key of shift+drag to this feature, wouldnt even have to turn off the standard right click option, I could deal with both being there.
View 1 Replies View Relatedmy problem is when i open cad 2012, the cursor keep become big.. i already try revert to default and it back to normal but when i close the program,cursor will revert again become big and hard to do draft.
My spec :
Acer aspire 4736z laptop
windows 7 64bit
4gb ddr2 ram
intel GMA 4500m graphic with latest driver
The instructions in Adobe Photo Elements 11 Classroom In a Book are the classic Windows "Drag and Drop" Method. However, when I try to do it, the cursor/icon I am dragging turns into a gray circle with a gray diagonal when it reaches the Media Browser pane in the Organizer and the folder/photo is not imported into the Organizer when I "drop." Do I need to change setting in Windows (Vista, SP2) or Photoshop Elements 11?
View 3 Replies View RelatedAt no specific time when using ACAD 2012 MEP the cursor disappears. cross hairs and all. the only way to get them back is to close ACAD and open it back up.
View 4 Replies View RelatedWith osnap on endpoint only, no other dynamic inputs on, no polar, 3dobject snap dynamic input, grid or snap on.
The cursor looks like it jumps up form the endpoint but actually it moves in the same Z as the osnap. Also when i zoom in i can't move my cursor to the upper or lower part of the screen depending on where I zoom too. If I turn magnet off it seems better but still not correct. In the drawing I uploaded I can't move the cursor up to the entities. If I open a new drawing everything works, on a different drawing everything works. If I insert this into a new file I get the problems back.
This is one issue that I really hate most in the mids of my drawing progress. Why my cursor are suddenly become invissible although it still active? My only option here to make visible again is to save and re-open it .
View 1 Replies View RelatedJust installed upgrade to 2012 on same machine as 2011. Within the drawing area of both Model & Paper space, cursor is jumping and slow across screen.
View 5 Replies View RelatedI wonder if it’s possible with Photoshop CS5 (OS: Win7) to control and navigate the cursor position automatically?
Situation: I have a layer with many scattered points.
Wanted: I would like to jump automatically (e. g. by mouse click) to every single point.
Or is it basically not possible because it is a Graphic- and *not* a Vector Software.
ON 3 different computers in my classroom, the cursor quits working in the graphics screen. You c an still click on any of the toolbars, palettes etc, type on the keyboard, but there is no response in the graphics screen area. In fact the crosshairs change to the "windows" arrow when the cursor is in the graphics area. I have had to re-install the whole system. I thought maybe is was a graphics crad/ driver issue but this is only occuring in AutoCAD 2013, I have not have any trouble in Revit, or other graphics based software that we use. I have video cards/drivers that are certified by autodesk. I have checked them for updates, etc. I have tried turning of the anit-virse stuff, nothing works except re-installing the whole system. It is random, I have 30 computers and so far 3 of them have done this. They are all configured the same.
View 9 Replies View RelatedI recently loaded several versions of AutoCAD on to a Windows 7 machine. ALL versions will open a drawing if double-clicked from windows explorer, but if I try to open through AutoCAD, the program freezes as soon as I click on the "Open" button. This is true for AutoCAD 2010 through 2012.
Machine Specs:
Dell Optiplex 990
250GB HD
8GB Ram
I7-2600 proc
AMD Radeon HD 6670 (1Gb) Video Card
I also cannot open multiple instances of ANY version of AutoCAD in Windows 7.
I try to load AutoCAD 2010 on windows 7 but it keeps on failing Language Pack - English failed installation aborted, Result 1624 so it rolls back and doesn't install.
View 9 Replies View RelatedHow to resolve the issue of : Displayed drawing keeps on vibrating everytime the cursor is move.
View 5 Replies View RelatedIs there a way to get a white cursor to automatically change to black when hovering over white images or hatches that doesn't involve turning off hardware acceleration?
System specifications: AutoCAD 2014 64-bit SP1, Windows 7 64-bit SP1, Intel Core i7-2600K, AMD FirePro V4900
16GB RAM, Crucial M4 SSD, 3 Dell Monitors (2 30" 2560x1600 & 1 20" 1200x1600)
For the past 2 months I've been using a Yiynova 10.1 tablet to design in Illustrator CS6. Later today I have an issue where the cursor would be on place but immediately move to a random area on screen. It is quick and I can keep my pen to point where I need to. However, everytime when I do close Illustrator the tablet seems to work perfectly. Photoshop and other programs seem to respond well with the pen and tablet, but Illustrator doesn't. I have ran a windows compatibility to all previous versions of windows and there are no results. I have reinstalled my Illustrator CS6 and the tablet doesn't want to play well still.
View 2 Replies View RelatedSystem Information:
Win 7 Pro 64-bit
AutoCAD Map 3D 2011 x64
Hardware:
Core i5- 650
8GB Ram
NVIDEA FX 580
Our company purchased two brand new computers and upgraded to Map 3d 2011 and it has resulted in major time lag and running slow issues. We use a 15mb city map as are main drawing file and in AutoCad Map 2004 it runs smoothly. After the upgrade thing are running very poorly. Selecting and deleting files that could be done in seconds in 2004 now can takes a 1/2 hour. The program also seems to get stuck periodical on a selected item , requiring restart. We have upgraded all the drivers and I have tried several different display drivers. I have saved the map as a 2011 file and I have repaired it. I have tried upgrading to Map 2012 but the problems persist.
I am currently drawing some roof tiles for a house in 3d. I moved the tiles to another drawing so i could get my machine to focus on the tiles rather than walls, windows, doors etc. My machine is still lagging hectically. Basically i would like to know is there a way i can perhaps make the roof tiles file smaller or a "block" of it so that my machine can run properly and i can import it into the drawing with the rest of the house. The roof tiles drawing is 40.3mb big. My machine isn't inadequate-hopefully.
I am on a mac running vmware fusion with windows 7 32-bit and when opening editing the roof tiles file my cpu % spikes to roughly 70% then backs quickly down to 50% and will not increase with Autocad not responding-leave it for a bit and it loads but lags a bit when i orbit, copy or whateva then back to not responding.
At work we have recently upgraded to Inventor 2013 Pro, Although Inventor isnt the most widely used program in the company so its hard to find time to do some set up and get it going smooth. My problem is that i am working on a large process plant all done in inventor and the file is quite large. It takes along time to load and is really laggy when inside the model. Now the model is based in my local office's server my question is if i was using Vault would it keep a local copy on my C:// rather than trying to refresh all parts from ther server. If it is a matter that when working with large files using Vault is the better option than i will need to take some advantages
View 3 Replies View Related-Inventor 2013 SP1.1 (Issue)
-Inventor 2011 SP2 (No Issue)
Templates have been coverted up from 2011, keeping copies of the old templates in separate folders all under the same parent directory.Have 2013 mapped to the folder with updated templates located on a network drive. Total of 18 temolates including the standard templates.
Computer specs:
Win 7 Pro 64bit Service Pack 1
Intel Core 2 Quad Q6700 @ 2.66GHz
8GB Ram
NVIDIA Quadro 2000
The Issue:I start Inventor 2013 or open an .ipt/.iam ect. I now want to create a new file so I click the "New" Icon.Inventor freezes for 10-15seconds and finally shows the templates.After that if you click on any of the templates it freezes instantly. Or if you scroll the browser bar down to navigate the folder. 15-35 seconds
After selecting the correct template it freezes for about 15 seconds.For those keeping track Thats 40-65 seconds just to open a drawing...
For Inventor 2011.Click, Click, Click. Open...Takes maybe 5 seconds.
