I am simply xref'ing a profile drawing into a sheet drawing to print out. AS shown on the attached, when the profile comes into the xref I lose all the band data and the EG line does not come in as a dashed 2 line as the layer is set to. It almost looks as if the PL linetype generation is off for this line.
View 1 RepliesWhat is the most current Civil 3D workflow recommendation from Autodesk, for people who are required to show and label three profiles: centerline, left and right gutter flowlines; on a plan and profile sheet for drainage review? The gutter flow line profiles are required to show their true longitudinal grade.
Just looking for the main salient steps at the conceptual level.
So I had to jump into the middle of a project. The Viewframes were already created but when I go to the plan and profile sheets for the viewframes the profile is not showing and I'm not sure how to choose the correct profile and display it in the corresponding plan and profile sheet.
View 8 Replies View RelatedHow can I show two proposed alignments in one plan and profile sheet?
View 3 Replies View RelatedExisting surface profiles not showing in xref. Constantly have to reload xref for profile to show. Even on opening drawing, reloading xref is required.
Civil3D 2013
Windows 7, 64 bit
Intel i7 2600 @ 3.40Ghz
16 GB RAM
Nvidia Quadro 600
I was given a horizontal centerline of a 5 mile bike path. We have to stake all the even stationing every 50 feet and all the VPC's and VPT's with vertical elevation. I have created the horizontal profile and also the vertical profile including all the vertical curve information. Is there an easy way to incorporate the elevation information back into the plan view so I can create points that carry x,y & z points that I can transfer out of autocad as a .txt file so we can upload it on our gps equipment?
View 9 Replies View RelatedIs there a way to easily add an object from a profile view to a plan view? I have developed a pipeline profile that has high and low points and I would like to show these points on the plan views.
View 9 Replies View RelatedI am trying to XREF my C3D Design file that has my profiles and sections in it into a drawing with a title block and viewport. Everything is fine in Model Space...but when I create the viewport in Paper Space none of the annotative text of the profile/section shows up...or is microscopic.
View 8 Replies View RelatedI found super elevation labeling for profile, but not for alignment in plan view. Is there a way to label alignment, f.x. in critical points of super elevation automatically?
View 2 Replies View RelatedI have a drawing with 13 profile views. 12 of them are working fine.
One profile view has 'lost' all its profiles. It should have one surface profile, and 6 superimposed profiles that are designed by layout in other profile views.
The profiles still show up in prospector and in the profile view properties, but you can't see them in the drawing. The profile view is on the same style as all the others, and the profiles are on multiple styles, but the same as their source profile and others in the drawing that are working fine.
I edited the alignment a little to see if that would 'jog the memory', then I turned all layers on and thawed. Still nothing. Then I superimposed a couple more profiles to see if they would show up. Again, they show in the properties, but do not plot in profile view.
I have a separate drawing with this alignment & profiles shortcut into it, and I'm seeing exactly the same behaviour there too.
i have some simple profiles and just want to show the pvi's in plan view on the alignment.
i made a reference label and it works great. now i am trying to figure out if there is a quick way to locate the pvi station on plan view other than doing something like create a point using sta. and offset as parameters hand typing in the info.
Is there a way to label corridor links in plan view ?. I would like to show my pavement cross slopes from corridor in plan view.
View 5 Replies View RelatedI'm working with plan production sheets and having some trouble. My vertical exaggeration makes me want to split the profile, but when I do it, they get glued together. My left vertical grid numeration stays on the middle of the grid and I get a lot of information overlapped. What I need is to put some gap between these, or split'em. Other issue is that the axis offset of my Profile Style isn't being applied, as well as other configs.
View 2 Replies View RelatedIs there a way of adding superelvation data such as full superelevation cross slope to an alignment curve label in plan view?
In my case we add a label for each horizontal curve with critical curve data such as PI Station, Delta, Degree of Curve, etc... but I can't seem to find a way of adding any superelvation information to the plan view as a label. Ideally I would like to be able to add the maximum cross slope value and superelevation critical stations to the label.
There is a way of adding the superelevation critical stations a labels to the alignment similar to how PC's or PT's are labeled, but it does not give the cross slope value.
I have 7 manholes in my network, only 3 of them are visibile in the model tab though.
There is structure label on all of the manholes
I can use select similar to mark them and i get "Structure (7)".
I can even see them in the object viewer.
AutoCad 2011 & Civil3D 2011. Product Version 3.
EliteBook 8560w
Intel i7 CPU 2820QM @ 2.3GHz
8 GB RAM
NVIDIA Quadro 1000M
Windows 7 Enterprise 32 Bit
I'm not too familiar with corridor styles. How can get points to show on my cooridor in plan view?
View 4 Replies View RelatedI have a label style creating a callout bubble for structures in a pipe network, but it keeps placing the label (and therefore, the leader when dragged) at the edge of the structure, and I want it to go to the center.
View 2 Replies View Relatedhow to show the inside diameter of structure in plan and profile view. Do I have to make sump and wall thicknesses 0 to do so?
View 5 Replies View RelatedWhen creating plan and profile sheets with multiple alignments in the view, what is a common practice in civil 3d?
- Data shortcut all alignments that are in the view into the plan and profile model
- Create a dwg that has all the alignments data shortcutted and xref that into the plan and profile dwg
- Create a dwg for each alignment and xref into an overall alignment dwg via attach and then xref the overall into the pp sheets dwg model.
Civil 3D 2012 SP4.0 Windows 7 Enterprise 64-bit
C3D 2014 SP1
Dell M6600, Core i7 @ 2.3GHz, 16 GB ram
Dell T3500 workstation, too much ram to post
I new to using the view frame groups we do allot of double plan view 11x17 sheets using an alignment on top of MrSid aerial drawings. It is very time consuming to setup the viewports along the alignment doing the old fashion method of copying the page setup and sliding the model space along the alignment for the next sheet. I understand the plan profile and cross section methods of creating multiple sheets and how the viewframe group works for those type of sheets. I'm just not sure how to create a dwt template for one plan view on top of another plan on the same sheet with to viewports. I know I'm not the only person that creates road cl double planviews when your not concerned about a profile.
View 3 Replies View RelatedI have used Autocad since 1991, and my current job required me to use Microstation. One feature I liked from Microstation is the ability to select and open an external DGN reference, and then match the view of the parent DGN, called the "EXCHANGE" command. In AutoCAD, you can also select and open an xref, but the DWG opens to the previous saved view, and not to the desired view that matches the layout.
My thought was to experiment with lisp or script and export the "Viewctr", "Viewtwist" and "Viewsize" variables to a text file, then importing the text file and using the "Viewtwist" as my "SNAPANG" value, then "Viewctr" as my "ZOOM, CENTER" value, and finally the "Viewsize" as the "Enter magnification or height:" value.
But, alas, I have no time, and not quite the knowledge to duplicate MicroStation's open-xref-and-zoom-to-view feature. I hesitate using the REFEDIT, which works fine for regular AutoCAD, but not so much for Civil 3D and the objects it creates (labels and other items with data shortcuts).
I'm setting up some plan and profiles (I DON'T HAVE CIVIL3D) with MAP3D. I have a couple of autolisp routines to work with the profile grid, but one thing that confuses me, the grid should be in paper space and the vertical scale set based on paper space, right? I'm assuming that the actual contours/polylines (once I have them georeferenced) will go in model space.
View 0 Replies View RelatedI am working in a project where I need to represent the reflecting ceiling edges in the plan view. I put the first floor plan as underlay, and selected the RCP projection but I don't see the dropped ceiling lines to select them with the linework command. I have done every thing possible with the view range but I don't see the lines.
View 7 Replies View RelatedPipe network storm pipes: Fairly new to Civil3D and trying to set up parts list for the storm sewer pipe and would like the plan view to appear as it does currently. We use a polyline for centerline of pipe, similar to dashed linetype but line and space are the same, width set to pipe width.
View 1 Replies View RelatedI am having some issues with surface profiles on a dreffed alignment no updating dynamically.
Currently it requires me to set them to static, then back to dynamic and they update.
I am well aware of the issue of dreffed surface profiles staying static. I am using the work around of dreffing in the surface and sampling in the drawing using the dreffed alignment.
Civil 3D 2014 (SP1)
Win 7 Pro x64
DELL Precision Workstation T3500
Intel Xeon 3.3GHz (w3680)
24Gb Ram
NVIDIA Quadro 2000 (1GB)
i draw up all of my walls, i connect them properly, cleanup etc. then i want to trim them with my roof slabs and what i see? i see my walls suddenly dissappear in 3d view but are still correctly shown on plan view? i know it has something to do with roofline because when i tried to project them automatically to ontu my roof slabs the walls dissappeared too!
View 1 Replies View RelatedI am trying to insert blocks into my drawings and for the most part I have been successful using Design Center. However, I have difficulties turning some of those blocks from the Plan View into the Elevation View, even when they show as elevation blocks. Even the downloads that show as 3-D end up being inserted as 2-D in plan view. In floor plan mode, I have no problem; so how do I turn them into 2-D in elevation mode?
View 1 Replies View RelatedI received a dwg plan in xref and the client whats me to make some changest to the plan what would be the best method of doing this? I tried xref editing and was able to make the changest but now it won't plot.
View 2 Replies View RelatedI have created room tags and would like to use the floor plan (with room names) as Xref. Is there a way I can locate the room names in one location per room on the main floor plan and then relocate the room names on the reflected ceiling plan and NOT move the room name on the main floor plan?
View 1 Replies View RelatedResidential custom home design. I come from the good old fashioned background of pencil and paper drafting. Although with the recent technology advances I have migrated to the AutoCAD side of the fence, and loving every minute of it. Upon purchasing a copy of AutoCAD 2004, I continued drafting the way I knew how, lines on paper. I have recently upgraded to AutoCAD 2007, and with no formal training, I am looking in drafting in 3D.
My main question has multiple parts;
What is the best way to draw walls in 3D?
What is the best way to add windows and doors? and is there a way to have the "plan view" relate with the "elevation view"?
How do you go about adding a roof?
I have played around in the isometric views attempting to solve the previous questions, although I have been doing all of it with line work. I know there has to be an easier and more efficient way of going about this....
We have our first project in Revit that we are having to split among multiple sheets because of the size of the building, so I have made 3 dependent views from the main overall view, named them, cropped them and placed each part (A,B, and C) on separate sheets. Now that I am trying to do enlarged toilet plan views, I want to tag the plans with the plan callouts on the 1/8” sheets that are the dependent views, but all the view tags are referencing dependent view A since it is the first dependent view in the list. If I change sheet A to be named Sheet X for instance, all the view tags now reference sheet B since that becomes the first dependent view alphabetically. I want them to reference the sheet they appear in, but I can’t seem to figure out how to do that, even though they are in different dependent views completely and within the crop region, they all default to the first dependent view in alphabetical order.
View 4 Replies View Related