AutoCAD Civil 3D :: Multiple Profiles On Plan And Profile Sheet?
Aug 5, 2013How can I show two proposed alignments in one plan and profile sheet?
View 3 Replies
ADVERTISEMENT
AutoCAD Civil 3D :: Three Profiles On A Plan And Profile Sheet
Aug 27, 2012What is the most current Civil 3D workflow recommendation from Autodesk, for people who are required to show and label three profiles: centerline, left and right gutter flowlines; on a plan and profile sheet for drainage review? The gutter flow line profiles are required to show their true longitudinal grade.
Just looking for the main salient steps at the conceptual level.
AutoCAD Civil 3D :: Getting Profiles Into Plan And Profile Sheets
Jun 17, 2013So I had to jump into the middle of a project. The Viewframes were already created but when I go to the plan and profile sheets for the viewframes the profile is not showing and I'm not sure how to choose the correct profile and display it in the corresponding plan and profile sheet.
View 8 Replies View RelatedAutoCAD Civil 3D :: New Plan And Profile Sheet?
Nov 2, 2013How can I create a own Plan and Profile Sheet?
I already spent much time trying do it but it was failed.
AutoCAD Civil 3D :: Plan And Profile Sheet Production
Nov 30, 2011I am having a "problem" with creating plan and profile sheets due to the large level differences in my profile. The plan and profile sheets are produced but the profile gets chopped off and I can't figure out how to get around it short of manually creating the sheets (which is a bit counter intuitive given Civil 3D's capabilities)
Is there a way of getting this to work??
AutoCAD Civil 3D :: Plan And Profile Sheet Layout?
Apr 9, 2013When creating plan and profile sheets is it possible to create the plan view with the alignment moved down to show more of project above the alignment? The default setting puts the alignment at the center of the plan view window.
View 2 Replies View RelatedAutoCAD Civil 3D :: How To Show 1500 Feet Of Stationing In Plan And Profile Sheet
Feb 21, 2013When I run my production sheets I'm only seeing 1300 feet of my profile and I like to see 1500 feet of my profile at 50 scale. Is there a way to show 1500 feet of profile?
View 9 Replies View RelatedAutoCAD Civil 3D :: Create Sheet Drawing That Has Two Plan Or Profile Views On Same Layout?
May 27, 2013I would like to create a sheet drawing that has two plan views or two profile views on the same layout?
View 2 Replies View RelatedAutoCAD Civil 3D :: Creating Plan And Profile Sheets With Multiple Alignments In The View
May 3, 2013When creating plan and profile sheets with multiple alignments in the view, what is a common practice in civil 3d?
- Data shortcut all alignments that are in the view into the plan and profile model
- Create a dwg that has all the alignments data shortcutted and xref that into the plan and profile dwg
- Create a dwg for each alignment and xref into an overall alignment dwg via attach and then xref the overall into the pp sheets dwg model.
Civil 3D 2012 SP4.0 Windows 7 Enterprise 64-bit
C3D 2014 SP1
Dell M6600, Core i7 @ 2.3GHz, 16 GB ram
Dell T3500 workstation, too much ram to post
AutoCAD Civil 3D :: Editing Profile Style Of Single Profile Instead All Of Profiles?
Mar 5, 2012I have a group of profiles in a drawing and I want to change how one of the profiles is displayed through the profile view style manager, but I do not want to change how all of the profiles look. Is there a way to change the way a single profile looks without changing all of them?
View 2 Replies View RelatedAutoCAD Civil 3D :: Xref'd Profiles In Plan View?
Aug 28, 2012I am simply xref'ing a profile drawing into a sheet drawing to print out. AS shown on the attached, when the profile comes into the xref I lose all the band data and the EG line does not come in as a dashed 2 line as the layer is set to. It almost looks as if the PL linetype generation is off for this line.
View 1 Replies View RelatedAutoCAD Civil 3D :: Plan And Profile Layout
Apr 30, 2012Is there any chance to fit plan and profile on one 11x17 layout without exploding and export to dwg? I can't do it because of annotation scale that change every time.
View 4 Replies View RelatedAutoCAD Civil 3D :: Draw A Waterline In Plan / Profile?
Jan 7, 2009What are the options for drawing utilities (namely water lines) in plan view and having them properly show in profile view?
I'm familiar with creating a polyline, turning it into a feature line, weeding vertices, etc. That works all right but is lnog-winded and really doesn't work well when dealing with lots of curves.
AutoCAD Civil 3D :: Plan And Profile Sheets Left To Right
Apr 6, 2010I have generated a right to left profile. I use General-create the view frames and they show right to left --good
I use General-create sheets to create the layouts in my current drawing . Rather than being from left to right, it flips my plan view upside down and aligns it on the left side. Is their a viewport setting I don't know about?
AutoCAD Civil 3D :: Plan Production Profile Views
Dec 14, 2013I am trying to use the plan production feature and I've got it working pretty well except when it creates the profile view, it cuts off the data band and also makes the viewport at the very top edge of the profile, so in the viewport I can't see the data band or the top edge of the profile view.
What setting am I missing to make it show the data band?
Civil3D 2014 SP1
Win 7 Professional - 64-bit
HP Z400
Xeon W3550 @ 3.07Ghz
24GB of RAM
Nvidia GeForce GTX 760
AutoCAD Civil 3D :: Position Of Cursor In Plan And Profile
May 10, 2013Is there any way of determining your cursor position in plan when you are working in a profile or visa versa? I also work in 12d and as you move your cursor on an alignment or profile you can exactly see the position of the cursor in both layouts/views.
View 3 Replies View RelatedAutoCAD Civil 3D :: Lost Profiles On One Profile View?
Mar 7, 2013I have a drawing with 13 profile views. 12 of them are working fine.
One profile view has 'lost' all its profiles. It should have one surface profile, and 6 superimposed profiles that are designed by layout in other profile views.
The profiles still show up in prospector and in the profile view properties, but you can't see them in the drawing. The profile view is on the same style as all the others, and the profiles are on multiple styles, but the same as their source profile and others in the drawing that are working fine.
I edited the alignment a little to see if that would 'jog the memory', then I turned all layers on and thawed. Still nothing. Then I superimposed a couple more profiles to see if they would show up. Again, they show in the properties, but do not plot in profile view.
I have a separate drawing with this alignment & profiles shortcut into it, and I'm seeing exactly the same behaviour there too.
AutoCAD Civil 3D :: Reference Profile PVIs In Plan View?
Jun 18, 2012i have some simple profiles and just want to show the pvi's in plan view on the alignment.
i made a reference label and it works great. now i am trying to figure out if there is a quick way to locate the pvi station on plan view other than doing something like create a point using sta. and offset as parameters hand typing in the info.
AutoCAD Civil 3D :: Feature Lines And Plan / Profile Sheets
Apr 17, 2012I have a low pressure sewer system that runs along a road side but is not always parallel to the road. I'm using hte centerline of the road for my alignment. What I need to do is have a profile of the existing ground above the centerline of the pressure pipes show in the plan/profile sheets. I do not need a profile of the roadway.
I'm currently using feature lines to accomplish this and that works fine in the main drawing, however, the profiles I create there don't transfer to the plan/profile sheets when I create them. The only way I have found so far to get thoe profiles to show in the plan/profile sheets is to create the feature lines in the plan/profile drawing and project those lines to my profile view. This is a fairly large system so I will have numerous plan/profile sheets. Creating the feature lines and profiles in the individual sheets is fairly time consuming.
I'm currently using Civil 3D 2012. I realize that with the addition of pressure pipe networks in 2013 might very well give me the tools I need but I'm at a point in this project, and our office, where switching to 2013 isn't really an option yet. However, if that is my answer then I will have to consider that.
AutoCAD Civil 3D :: Profile View Style X Plan Production?
Jul 9, 2013I'm working with plan production sheets and having some trouble. My vertical exaggeration makes me want to split the profile, but when I do it, they get glued together. My left vertical grid numeration stays on the middle of the grid and I get a lot of information overlapped. What I need is to put some gap between these, or split'em. Other issue is that the axis offset of my Profile Style isn't being applied, as well as other configs.
View 2 Replies View RelatedAutoCAD Civil 3D :: Plan And Profile Bands Are Shrinking - 2010?
Jun 15, 2011When I am doing my plan and profiles I have come across a couple of instances where when I am ready to plot or just switching over to the layout tab that the bottom bands of my profile have shrunk. Is thereanything that i can do to stop this or to easily restore them back to normal size? Could this be a Civil 3D 2010 issue or more likely an issue with the template that we had built for our company.
View 6 Replies View RelatedAutoCAD Civil 3D :: Multiple Revisions On One Sheet And Sheet Set Manager
Nov 6, 2012How people deal with multiple revisions of one sheet with sheet set manager, basically I want the cover sheet of drawings to have a list of drawings including the revision letter and revision date and on each individual sheet keep track of historical revisions
There is the current sheet revision and date fields.Does everyone usually just update these and manually keep track of historical revisions else where in there title block?
AutoCAD Civil 3D :: Creating Layout Tabs For Plan And Profile Sheets
Dec 18, 2013I am running civil 3D 2014 and have several lisp file that I have added to my startup suite. I am creating layout tabs for plan and profile sheets and use my lisps continuously and then all of the sudden it tell me that it's an "unknown command". I have closed the program and reopened the drawing an I realized that my start up suite is now empty.
View 2 Replies View RelatedAutoCAD Civil 3D :: Show Inside Diameter Of Structure In Plan And Profile View?
Jul 9, 2013how to show the inside diameter of structure in plan and profile view. Do I have to make sump and wall thicknesses 0 to do so?
View 5 Replies View RelatedAutoCAD Civil 3D :: Identify Flowline At A Point Along A Pipe In Plan Without Creating Profile
Jul 9, 2013I'm looking for a way to simply get a flowline elevation at some random point along a pipe (Network) in plan view without having to go through the trouble of "drawing Parts in Profile".
I have successfully added invert elevations at the ends of the pipe, but that's not what I'm looking to do & "ID" command shows the "Z" elevation for pipes in pipe networks to be "0".
AutoCAD Civil 3D :: Convert (scanned Plan And Profile) For Pipeline To Feature Line
Aug 13, 2013I have a 2D (dwg) plan and profile of pipeline ( Scanned) and I am going to find a way to have this pipe as 3d ( or featureline).
I can't do this manually because this is a long pipe.
AutoCAD Civil 3D :: Plan Production - Pipe Network Profile Labels Are Missing In Sheets
May 6, 2012In plan production, I have created the sheets (plan & profile) as a seperate drawing.
when I open the sheets, the pipe network profile labels are missing in model & paper space. (attachment 01)
I tried to on/off the annotation visibility tabs in the lower right corner (attachement 03)
Note: While creating the sheets, I select the tabs for pipe network & copy pipe network labels to destination drawings (attachment 02).
AutoCAD Civil 3D :: Plan Production With Multiple Views?
Dec 1, 2013I am trying to use plan production to generate sheets for a long, skinny corridor. I wanted to put two plans onto a single sheet.
I have tried a few settings, but get a duplicate of the same plan. Is this possible, or is necessary to do it manually.
AutoCAD Civil 3D :: Profiles Show Up Under Multiple Alignments
Jul 24, 20122012 SP2
I'm having a problem with profile shortcuts showing up under multiple alignments. I have 16-alignments and profiles in their own drawings. I didn't create the shortcuts right away as I was still figuring out how I wanted the project dir structure. When I had that solved, I started creating the shortcuts. When I checked them, some of the alignments had up to 6-profiles from other alignments listed under them. One alignment had 3-profiles, and not one of them was for the alignment.
I removed all the profile shortcuts and started bringing them in again. Same problem. This was after shutting C3D down, cleaning up the tmp files and restarting.
There are shortcuts for 36 other alignments, and none of them appear to be affected, only these last 16. Validate Data Shorcuts doesn't do anything.
AutoCAD Civil 3D :: Delete Multiple Profiles At The Same Time?
Mar 15, 2011there is a way to delete multiple profiles at the same time?
Currently, I have to go through the prospector and delete them one at a time. I have an alignment with many profiles (various walls along the length of the road), but have split the drawing up into several files... How can I delete all the profiles at once?
AutoCAD Civil 3D :: Profile Sheet Vertical Scale Is Off By 4'
Mar 14, 2013When I make profile sheets the vertical scale (text) if off by 4' (below). I checked all the settings and they appear to be correct. When I make a profile the scale is correctly shown.
View 1 Replies View Related