If we have both the Xref and the File that it is referenced into open on one of the computers here and we reload, the Xref disappears. If we do an undo and close the Xref it reloads without problem.
I tried to replace the user profile from another PC that doesn’t have the problem, but it didn’t work. Is there a Registry setting that cause this behavior? All stations set to “Enabled with copy”
AutoCAD 2012 Arch.
We are using ACA2010 and use the project navigator to bring constructs into views then bring the views into sheets, which has been working great, but in the last few months we have gone to a sheet only to find that the view no longer contains the constructs. I was working on a project on Friday and the Site Plan view no longer had the site xrefed into it which I fixed, now today the Site Plan is fine but the Roof Plan is empty. This is not the 1st project this has happened to but it is the 1st time it has happened to me so I know nobody changed something they should not have. Is there a known bug in 2010 or something I should check. I don't want this to happen to the Floor Plan if it does I will lose all my dimensions.
View 2 Replies View RelatedProgram: Civil3D 2010
Upon binding my dwgs to send to clients, sometimes I run across a serious problem. My xref'ed site plans disappear but my xref manager still lists it as attached, the layer manager still has every xrefed layer, and all other xrefs in the dwg will bind perfectly.
I have broken down all complex objects, purged, audited, cleaned up any excess scales, and even created new fresh dwgs for the xref and the drawing in question; all actions have ended in failure. I have even searched the AutoDesk forums for a solution and have found nothing substantial.
Solution: #1 Use RECOVERALL command on .dwg file that the xrefs disappear from. It will remove all proxy objects and excess scales in the file that is causing it to disappear in the first place.
#2 WBLOCK out the dwg file and any xrefs that are disappearing and insert them into new "clean" .dwg files. Must be done to all files.
I am using 2010 and when I am on my sheet or viewing my database through a viewport annotative objects tend to disappear and it happens randomly. It's only a few objects that will disappear while others are shown.
Example: My grid bubbles may disappear, but leaders, text, dimensions, etc are visible.
Another example is door or window tags may disappear while grid, leaders, etc are all shown and when they don't show up they also don't print. Reloading the xref doesn't bring them back also. I have to physically go into the database and make some kind of change (erase a line and than undo; draw a line and than delete it; change a scale, anything); save the drawing and then go to my sheet and reload the xref to get them to come back.
Installed AutoCAD 2012 3 days ago.
I have noticed the layerstates of the xrefs in my drawings are disappearing. I have to close and reopen the file for them to reappear. Can duplicate this error? At the moment i haven't been able to pinpoint when it happens, but its a first in my experience. I just installed it on another staff members computer so i will see if they get the same problem and report back.
OK. I discovered it occurs when you unload the xrefs, then reload them in the drawing. I was able to duplicate the same problem in a seperate drawing on another computer.
Any registry setting (or some othere way) to disable Autodesk 360. My users have no reason to use this feature and I don't want them wasting time with it.
View 5 Replies View RelatedI'm trying to fix my profile via lisp-registry key. Why? Because the profile we use is part of a plug-in meaning we can do it using our profile so I alternatively the answer is to tweak the one supplied as part of the plug in.
The method I’m familiar with is to edit using the following code as example;
(vl-registry-write "HKEY_CLASSES_ROOT\.PEN\Shell\open\command" "" "notepad.exe %1")
However that’s for creating a new registry key entry the one I have already exists but needs to be modified, better yet the profiles name (*.arg file) can change with updates, so in my search I came across the following link.
[URL]
Now I cant put it together and am not sure where I have gone wrong…(See code bellow)
(vl-registry-write "hkcu "\Profiles\" (getvar 'cprofile) "\General\DefaultConfig" "\\DCMAR02\A03P20")
I've got the second floor of a building which is an attic, which is over 2 different levels, each of which has its own xref. The roof is sloped. I would like to vary the cut plane in the same view, so that both xrefs are respectively cut at 1500mm above floor level. This would mean using 2 different cut planes, one for each reference.
View 1 Replies View RelatedI have an xrefernced drg , which i print from a layout/paperspace .I freeze certain layers using VPort freeze in layer properties and save the drg whenever i close and reopen the drawing the layers are thawed in the viewport again.
View 2 Replies View Relatedfew of our systems are not loading the xrefs automatically. it show as UNRESOLVED until reload it manually. also this systems are not able to attach / overlay xrefs as relative path.
View 7 Replies View RelatedI'm using Autocad 2013. My problem is when i use "recover files & xrefs", all the files recovered are saved as a 2013 dwg version. As we all save our files here as 2007 version so when others opened the files they are getting some of the xref files missing in the drawing.
Is there any option to save files in a lower version when i recover?
I've recently run into a problem that involves xrefs. Basically, I cannot open files that are being xrefed in other drawings when those drawings are currently open. AutoCAD Architecture will only allow me to open the xrefed file as a read-only version. For example:
I have 1ST FLOOR PLAN (drawing file) xrefed into A-201.00 FIRST FLOOR PLAN (sheet file). If one of my team members has the sheet file open with the drawing file loaded, then AutoCAD will only let me open the drawing file as a read-only file. But if my team member has the sheet file open with the drawing file unloaded, then I can open the drawing file without any problems.
I have never had this type of problem with xrefs before and so I'm wondering if it's an AutoCAD Architecture 2012 bug.
What is the best method to re-path x-refs in a project whose folder has been moved. We are talking about 60-100 x-refs here.The originals were created in ACA 2009 and were not pathed relatively; nor was Project Navigator used. We are currently using ACA 2014.
View 1 Replies View RelatedWhen an object in an XRef is tagged (and the object has an object based PSD) the tag will not update to reflect changes made in the XRef.
This can be fixed in the XRef by running the PropertyDataBrowser command and unticking the Overrides (shown in the leftmost tickbox when two tick boxes present).
Any automatic way to keep the tags up to date? I have attached my VB.Net code attempt for this. It almost works BUT the MultiViewBlock Overrides are ReadOnly.
Our office recently moved all of our project files to the dropbox. Now when I open files with xrefs I have to attach them back into the file. However, this doesn't happen for my coworker. She can see all the xrefs. How could I solve this? The file names or directory has not changed.
View 2 Replies View RelatedAfter working in civil 3d for a while they will disappear. have to close toolspace and open again. have sp1 installed already.
See picture for detail. as you can see only toolbox is left. and when i select toolbox from general menu. the whole toolspace will shut down.
Running AutoCAD 2013.
I created a .dwt template for general use with plenty of a various paper space layouts and such. I also created a bunch of styles for text, dimensions, multileaders, and tables for both paper and model space. After saving the template, those styles will still be there any time I open up a new drawing with that template. After working a bit and then saving the drawing, the styles will all be gone once I open it again.
Re-opening the original template always has all of the old styles still saved, so why would they disappear once I use that template on a drawing?
How to keep the snap mode settings from disappearing after certain commands. For example every time I use a lisp routine I have to go and reset my settings because they are no longer the way I had them set before I performed the lisp command.
View 9 Replies View RelatedUsing ACA 2012 and Windows 7 Pro x64. I have a drawing with two viewports. In one I'm showing the electrical layers and the base floor plan. In the other I'm showing casework and the base floor plan. All of the layers are contained in one xref so some are frozen in each viewport. When I bind that xref using the insert method (bindtype=1) some of the electrical layers show in the casework plan. I've tried everything I know of but I can't figure out how to surpress this behavior. If I use bindtype=0 the problem goes away but I end up with ugly layer names.
View 1 Replies View RelatedI am having several problems with my xrefs. My two big problems are xrefs bringing in way more information than I want, and they are duplicating if they are selected, even when I have the xref layers locked.
My set up is this:
I have a plan file, a grid line file, an elevation file, and a section file.
I want all files to be referenced to each other. However, I do not want duplicates of any xref. For instance, in my section drawing, I will reference my plan file which consequently brings in any file that is referenced in the plan file. I know that I will get the circular reference warning and that I can click continue. However, is there any way I can just get "1 degree of nesting"?
Second, I cannot figure out how to lock my xrefs to prevent them from constantly being selected. My problem is that in my live drawing information, if I select everything within my window and an xref is in that window, it will be copied. I don't ever want to duplicate my xrefs, but I can't find a way to lock them (even when locking xref layers).
I know the possibility of a plot style just disappearing is slim to none, but I have this user that constantly claims her plot styles have "disappeared".
When I check them, the entire "Plot Style" folder is gone. One day it's there the next it's gone.
She also has this problem with the DWG to PDF print option. It was there, now it's gone. She claims she isn't deleting anything. I will get them back on her PC and a few months later they will be gone.
She is a contract worker who also spends time at her office off site. I am not sure what version of AutoCAD she is using. I manage an AutoCAD group of about 20 users and none have this problem.
Every so often while working in LT-2010 the cross hairs will vanish from the screen but you are still able to pick items (as u move the mouse lines, etc hi-light in the usual way) also when you come outside the drawing area the mouse pointer will reappear (only while outside the drawing, in the command bars, etc)
the only quick way to return the cross hair to normal is to hit another tab & then re-enter the tab or model i was in. there seems to be no particular command that causes this glitch .
Im new to autocad and started designing my own house in archictecture 2010.
I've been having a propblem with the roof design at the moment, i am trying to get the gable ends of the roof to stand up on a 90 angle on both sides by editing the edges/faces but every time i do this the roof ends disappear so theres a hole in the sides of the roof and you can see into the house. How to do this so they do not disappear?
We have just installed ACA 2012 on one of our workstations and randomly the crosshairs will disapear in paperspace. We will still get the cursor icon if we hover over properties and paletts etc. We have the latest service pack and ribbon hotfix. Searching hasn't come up with much.
View 4 Replies View RelatedI'm not sure what happened but all of a sudden when I try to open an existing drawing it no longer pops up a box to browse, it asks me in my command bar at the bottom to type in the name of the drawing. The same thing happens when I try to "save as" a drawing... How to get this back to normal?
I have attached a Jpg of both instances...
I recently added a block ( by dragging & dropping from our dws block library file) to our shared Tool Palettes. The block showed up properly on everone's computer the day I added it. However each morning when we restart our computers the block is no longer on the palette and I have to redrag & drop it. I thought that prerhaps I needed to export the updated toolpalette, but when I go to the customize tool palettes dialog box and right click on the toolpalette I don't see the export or import options. I am at a loss. We are using AutoCAD Architecture 2013
View 1 Replies View Relatedwhen doing the "distance" command, typically as you go from point to point, the distance will be listed on the page next to my cursor as I go. Then if you left click, right click, it will list the final distance down in the command window. The machine in question no longer displays the distance on the page as you go. This is a very useful feature for us, and although we can distance things, using the text readout in the command window takes much longer.
View 2 Replies View Relatedi have a large number of drawings that need xrefs detached and re-attached with the latest model xrefs, any way to do them in bulk rather than opening each individual drawing? the problem started a while back, when opening drawings, ACAD is not loading the latest 'saved' model when opening drawings...
View 5 Replies View RelatedI am trying to get renovation mode to work properly. When i use it it seems to change item that existing to a new layer on color 8 (I specified color 8), but not to by layer. I want to be able to assign an item and have the color be set to by layer instead of a forced color.
It also changes everything in the drawing. Say i have multiple objects on layer A-Wall, it changes all those objects instead of just the one i select.
You would like to adjust your SNAP settings within your software.
View 1 Replies View Relatedhow I can move a user from one computer to another and have them keep all of their settings in AutoCAD Architecture 2013.
We are upgrading user laptops. I have used the Windows 7 Easy File Transfer utility on the first couple, but it does not appear to copy the users AutoCAD settings. When they open AutoCAD for the first time on the new computer, they have to set up all of their toolbars, etc again.
I have even tried copy and paste of theWin 7 AppData Local, LocalLow and Roaming folders ... but even that does not tranfer over the toolbars, menus, etc...
make it so that when a user logs into the new computer and opens AutoCAD, it is exactly as it was on the old computer?
