AutoCAD 2010 :: Same Layouts In One Drawing But Slow Switching To One Of Them
Dec 6, 2013
i have a test drawing attached with layout 1 and layout 2.
from model to layout 1 takes 2-3 seconds on my crappy computer, from model to layout 2 takes 8-10 seconds on the same crappy computer.
this sample i attached has a xref binded. which result is the same 3 and 8 seconds respectively.
you may think this is not a big deal. but layout 1 will take 10 seconds to to switch to if you have 5 xref while layout 2 will take a minute.
i did my research and haven't find the difference in variables between the two paperspace layouts.
tried all the variables made no difference:
psltscale, msltscale, celtscale, savefidelity, etc.
also set both viewoprts to undefined same thing.
the only difference is "1" is created from a blank autocad template by selecting "metric - no template", and "2" is imported from a civil 3d dwg after done a plan/profile production and that thing created that layout.
is there a tool to compare all variables between 2 layouts and find the differences? i am certain the problem lie within system variables.
Civil 3D 2012
Work: Xeon W3503, 12GB, Quadro 2000, Dell P2211H x 2
Home: 3930k, 12GB, GTX 590, U3011, QX2710
View 9 Replies
ADVERTISEMENT
May 21, 2013
We installed Autocad LT 2014 on our new computer and I noticed that it is unusually slow to switch between layouts.
The bottom bar (where the paper/model space button is) kept flashing/switching as if its thinking whenever i click from one layout to another. Even when I'm zooming in and out, the bottom bar kept flashing slowly.
I was hoping that a new computer+new cad will make our work more efficient and faster, but i noticed theres a lot of lagging and general slowness in loading files.
View 7 Replies
View Related
Oct 17, 2012
When I work in large files (10,000 kb +) I experience significant delays when copying large amounts of information (copy a floor plan) or when switching between layouts or saving the dwg. I wish I could tell you it started right after I But I just recently started working with the larger files. So this could have been an issue from the time I bough the machine - 18 months ago.
it's either an issue with my graphics card or processor. I would like others to comment on their opinions on adjust my set-up to be more efficient
I believe I have the most current driver for the video card. Did I hear right somewhere that there is no good driver for the Quadro 4000 to work with 2012?
View 6 Replies
View Related
Apr 22, 2010
When switching from layout to model space, and back again, and when switching layouts the regen is slow to an extreme, upwards of (3) minutes. Using Renenall in layout, the regens are quite slow as well. Windows 7, AutoCAD 2011, NVIDIA Quadro FX1800, most current driver.
Additionally, when publishing, the regens are equally slow. LAYOUTREGENCTL setting seems to have no affect.
View 9 Replies
View Related
Jan 30, 2013
I have a delay when switching back and forth between model space viewports,
View 7 Replies
View Related
May 13, 2010
When using the undo command, plotting or switching between drawings in Autocad 2010 and now also 2011 I am experiencing long delays of up to 15-20 seconds at a time which is rather frustrating. I am running a fast spec computer and can't seem to overcome it, I haven't had the problem with 2009 and when need to do something quickly have found myself using the outdated software. Other users in the same office have equal or lesser spec computers and are not having the same issues, I have tried a re-install and this hasn't worked either. I was hoping the new 2011 version would solve this issue but no luck.
View 9 Replies
View Related
Mar 2, 2012
Problem 1 Most of the time when I am switching in between drawings that are open I have to "regen" the drawing that I switch to as nothing shows up when I switch.
Problem 2 Problem is copying layouts over. When I go to designcenter and then open drawings I try and drag a layout into a different drawing. Somtimes it works but usually I drag it onto the drawing and the new layout doesn't appear. I had this problem ever since I switched from 2010 to 2011 and now 2012.
View 9 Replies
View Related
Mar 2, 2010
We have a huge vault of old CAD drawings and the issue that we keep running into is that once some of these drawings are plotted and the drawings is re-saved the paper space layouts are flipping from landscape to portrait ignoring the default plot settings.
So we end up having to go to each paper space tab and individually switch each page back to landscape and then save, after that the drawings is usually good and won't repeat the problem but it's a real hassle as some of these drawings have a few dozen pages.
Is there any way to remedy this from happening or at the very least is there a way to select all the paperspace tabs and switch the page orientaion of all of them in one shot? I'm at my wits end trying to figure out something that to me seems as though it should be much easier, i.e. highlighting all the tabs and changing the settings for the bunch but alas CAD does not allow this.
View 8 Replies
View Related
Oct 5, 2012
When I try to switch to a different layout in a drawing AutoCAD will switch to a different drawing. Then I have to go and get back to that drawing to do anything to the layout.
View 9 Replies
View Related
Oct 25, 2013
I'm having an issue in 2014 with switching between model and paper space. It takes 4-to-5 seconds for me to begin working in these spaces, after switching. Going between tabs is not an issue, it's just switching between model and paper space that causes the lag.
View 2 Replies
View Related
Aug 13, 2012
I use Cad for Mac 2011. I am looking for a way for switching views quickly when drawing 3d. For the moment I use VIEW and then TOP, SE or whatever. It´s a bit slow. Also I couldn´t find out how the actual view is indicated.
View 7 Replies
View Related
Jul 18, 2013
Switching between each layout tab takes about 23 seconds.
What I know about the drawing:
-using AUDIT reveals no errors in drawing.
-Main drawing = 840 KB
-5 Xrefs total
-each Xref less than 1 MB each
-15 Layout tabs total in main drawing
-LAYOUTREGENCTL set to 0, 1 or 2 has no change on situation
View 6 Replies
View Related
Jun 5, 2013
How can i get number of layout in the current drawings?
View 3 Replies
View Related
Mar 6, 2012
I am looking at modifying a drawing template that contains several layouts (A0 to A4 size pages). We want to be able to input drawing information for the title block in one place and duplicate the information across all of the layouts without manually copying it across (in an effort to enforce 1 dwg per drawing). Looking into this, one way looks to be using dwgprops to define the text content and then use fields to populate the required parts of the title block...
My question is this: Is there any way of setting it so that when a user starts a new drawing, a prompt comes up on the screen asking for the pertinent information before the drawing is started and the user forgets to put the right info? Lsp or other means can be considered.
View 1 Replies
View Related
Sep 11, 2012
I am using autocad arch 64 bit on win 7 and am having problems switching out of xref classic so that the newer xref dialog comes up. i edited the SDI but then i cant close a drawing and opening creates more problems.
is there a way to get the xref dialog back?
View 9 Replies
View Related
Jul 16, 2012
When I add an object field in paperspace to report on the scale of a viewport in the layout, as I return to that layout and zoom in or out the viewport displays as hot in MS (tab reports as PS) and leaves the MS information of my previous visit embeded on the layouts neutral background and the "new" zoomed MS information is added to modelspace. The background objects cannot be selected or deleted but if I go to the block editor screen -choosing any block for my selection, when I close the block edit and return to the layout, the objects are cleared. I have installed service pack #1 for v12 and I lso have installed V13. I didn't notice this problem prior to the service pack or usin v13. I have an Intel i7 processor, 64 bit.
View 4 Replies
View Related
Nov 5, 2013
Since updating a drawing last week and saving it in paper space, I can no longer get back into model space without the drawing crashing.
how I can get back into model space and do some work?
View 9 Replies
View Related
May 26, 2013
Example for creating layouts for the zoomed portion in the model space.. Im able to zoom the drawing sheet but im not able to create layout for that sheet..See my attachment ..i created layouts manually(layout1,layout2,layout3)....But i dont know how to do this in .net API.
View 1 Replies
View Related
Jul 9, 2012
Am using Autocad 2012 with SP2 downloaded, note the problem does not occur in Autocad 2013... So basically if you open the dwg you will see it opens in paperspace, the viewport is locked to a specific scale etc. Now go into model space where the dwg is, you should be able to zoom around, pan etc fine, problem is when you now go back into the layout or paperspace. You will notice that upon re-entering paperspace that the vport is highlighted, ie there is a thicker outline of the vport boundary, however am still in paperspace according to the tabs. When you now try zooming in or out using the mouse scroll you will notice an additional copy of the viewport is imprinted on the screen. Thats the problem. Doing a few undos will set you back right again.
So far we are inclined to think that its either something to do with the UCS or the units that the program is getting confused with but havent been able to find a solution. Also bear in mind that it seems to work fine in 2013. Its probably something really simple that we've missed but thought would try anyway Will attach the dwg file.
View 2 Replies
View Related
Mar 4, 2012
(Again) Switching the “data type” of the cell,I’m not sure why the AutoCAD doesn't allow changing the “data type” of the cell in the table for already existing data. For example, in the attached table, I wanted to switch the “data type” from “decimal number” to “percentages”, but sounds that the AutoCAD doesn’t allow this function.
In the Excel, for example, we can switch the “data type” easily by selecting the target cells and choosing the format we need! Quite simple, in the AutoCAD, it seems that it needs some work around!
View 3 Replies
View Related
Nov 1, 2012
I asked this a long time ago but I'm hoping something has changed. If I have 2 Modelspace viewports is there any way to switch their contents? Right now I create 2 views and restore them in alternate viewports.
View 1 Replies
View Related
Feb 25, 2012
Switching the “hatch” to be “associative” gives “not applicable”!
I’m wondering why as I choose the “yes” for the “associative” property of the “hatch” then this gives “not applicable” as shown in the screenshot below
What might be the reason?
View 2 Replies
View Related
Jun 7, 2012
I have been trying to figure out how to copy a Layout from one DWG to another. I know there are several threads about this, and I have tried the methods they reccomend, but I am having an unusual problem.
I have been trying to open a Layout by using the "from Template" option for creating a new Layout, then opening the DWG containing the desired Layout. It works, but everything drawn in model space ends up compressed into the lower left corner and there is nothing in model space. So, the paper space information from the Layout is being imported, but the drawing info is getting mixed up somehow.
I have tried using the Design Center with identical results.
View 5 Replies
View Related
Jun 10, 2011
When I try and import layouts as sheets, the "Prefix sheet titles with file name" is subdued. (AutoCAD MEP 2012)
View 3 Replies
View Related
Sep 14, 2012
DView commands. We're using layout drawings of sites that are aligned with True North.
We've been using DView to rotate site layouts within model space in order to to align the layout better within the window and set up icons as such. And we have multiple Sheets set up with different information being displayed (ie different layers turned off). But when we go to the sheets, the Paper Space view still shows it's Original Orientation.
What I'd like to know is there a simple way to set the various different layouts to the same as Model Space, Without having to manually DView each Viewport as well?
View 2 Replies
View Related
Jan 4, 2013
I am trying to organize my drawing in model into different viewports for printing purposes. However, in Layout # 1, once I delete an item it also deletes the item in model space. In Layout # 2, can't edit, select, highlight or anything ( I am in Layer 0). How can I fix that ? Basically, I want to create several layouts, each layout will contain a certain section of my drawing in model space then. I am not "layout savvy", trying to get hang of it.
View 2 Replies
View Related
Oct 26, 2012
How to use Autodesk's DWG to PDF driver to plot multiple through publish? Whenever I try to plot more than one layout at a time I get a driver not found error.
View 2 Replies
View Related
Feb 19, 2013
when I publish multiple layouts to a single pdf. When I publish all the files at one time the right side of the drawing where the title block is cut off about an inch and does not show the complete title block. Publishing to a printer as a multiple batch or publishing the layouts one at a time to pdf does not exhibit this problem.
View 2 Replies
View Related
Jun 15, 2013
Is there an LISP file that can zoom extends all layouts?
View 1 Replies
View Related
Jun 21, 2013
I am looking at streamlining page layout configuration. When I say this, I mean that I want there to be a button, a small msg to type into command line, or any general quick shortcut, to create a new Layout based on a specific template layout that is located on my server. There will be multiple template layouts that the user has the option to choose from when creating a new one, with each layout contianing an xref title block, and a particular size . Also, I would like these to avaiable everytime I open autoCAD, regardless of the current drawing being worked on.
I've looked at Macros and Sheet Sets, but I was wondering if there was an optium way to do something like this? I realize its a failry begginger problem but I am still a begginer at autocad.
View 2 Replies
View Related
Oct 4, 2013
As you smart individuals can figure out, we do up drawing packages for construction that consist of several drawings, hundreds of drawings, for several modules of construction. Our process usually consists of one layout per drawing, so that the lisp guy can do a drawing count and put in sheet numbers based on how I manipulate the list of drawings in the one directory folder.
Now I have a client, despite the way we currently do things, requires that about 70% of the drawings will have multiple layouts. Now we're back in the stone ages, manually putting in sheet numbers, eating up our budget for this contract.
View 4 Replies
View Related
