I asked this a long time ago but I'm hoping something has changed. If I have 2 Modelspace viewports is there any way to switch their contents? Right now I create 2 views and restore them in alternate viewports.
View 1 Replies
Is there a way to see and move paperspace viewport boundaries in model space?
Explaining: You have created layout which includes multiple viewports with different scale and size (view, section). Now you copy the layout to create a new layout with with same viewports. Now you have to change the view in all viewports. I have used technique where you double-click in viewport and you navigate in modelspace (pan/zoom) until you reach the right position.
The problem is If you have like 100 layouts with 10 viewports each, it takes very long time to pan the views into right position.
I have a some theories:
1. If I could see the viewports in modelspace, I could drag them all into right position without navigating them one-by-on in paperspace.
2. If I could pan the view in viewport by specific amount lets say 10m to the right.
Am using Autocad 2012 with SP2 downloaded, note the problem does not occur in Autocad 2013... So basically if you open the dwg you will see it opens in paperspace, the viewport is locked to a specific scale etc. Now go into model space where the dwg is, you should be able to zoom around, pan etc fine, problem is when you now go back into the layout or paperspace. You will notice that upon re-entering paperspace that the vport is highlighted, ie there is a thicker outline of the vport boundary, however am still in paperspace according to the tabs. When you now try zooming in or out using the mouse scroll you will notice an additional copy of the viewport is imprinted on the screen. Thats the problem. Doing a few undos will set you back right again.
So far we are inclined to think that its either something to do with the UCS or the units that the program is getting confused with but havent been able to find a solution. Also bear in mind that it seems to work fine in 2013. Its probably something really simple that we've missed but thought would try anyway Will attach the dwg file.
For some reason, I have 1 drawing that will let me select and modify some dimensions in a Paperspace viewport, but others are nonselectable. I can go to the Model Tab and select any dimensions I want.
If I select the dimension in Model Tab, I can go back to Paperspace Viewport and select that dimension, but now dimensions that were selectable before are nonselectable. unsure:
I am thinking it may be graphics card issue or some sort of limit.
I received a drawing this morning, and it's paperspace looks great. However when I tried to view the drawings in modelspace it was empty. All the layers are on, when I click into the viewport (in paperspace) I can draw a line on the same layer as the block and that will show up in modelspace, yet no block.
Is this a feature of CAD, never experienced this before.
P.s. The blocks are available to insert in modelspace , however I'm just curious as to why I can not see the blocks that quite clearly exist in modelspace already.
I need to find the center point of a viewport in modelspace. I am looking for a vb.Net example but I can't seem to locate one.
View 4 Replies View RelatedHow would I go about inserting a field in modelspace that indicates the scale of a viewport. I only have one viewport.
View 5 Replies View RelatedA problem we are having in our office on 1 computer is that this message appears in the command line
'viewport is view locked switching to paper space'
It happens whenever we zoom or pan into one of our locked viewports. We have purposefully locked the viewport so we don't lose the scale when we zoom or pan and want to leave it this way, however, whenever we zoom or pan this message appears and it takes 30 seconds before the screen readjusts to the zoom or pan we require.
I would like the viewport shading to remain on the "smooth" visual style. The problem is, after I configure it max will switch back to "smooth + highlights".
See image below
I have a project where 60 drawings will be duplicated for each of a dozen sites. Each site has a four digit prefix (i.e. 800X) that is added to the drawing number, equipment callouts, leaders and various notes throughout the sheets. Even using Find/Replace, this is a lot of work to revise every time I copy them, so I’m thinking that this is a job for fields, no?
Well, I had no problem making a “global” field called SiteNo and inserting it into the title block. Then I inserted the same field into a couple of references in the general notes as well, where it works fine. But when I put it into several leaders sprinkled throughout the drawing I found a problem: regen or regen all will update the title block and note references (all in paperspace, of course), but not the ones in model space. I’ve tried putting the field in both mtext and dtext, and I’ve checked to be sure FIELDEVAL is set to 31. Nothing makes fields in modelspace update.
But I know that the field is set up correctly. If I doubleclick any modelspace occurance (text or mleader), then right click and choose “update field”, it fills in the right value. This however negates my goal. If I have to select each one, I might as well put it in as text and use FIND/REPLACE on each individual drawing.
I was REALLY hoping that I could go to the properties of the sheet set, change one box, and see all occurrences in all drawings for that site update, which is my understanding of the purpose and power of fields. I've spent a lot of time searching the web, seen a lot of issues and solutions, but nothing that quite hits my problem.
The AutoCAD deadline-sensor is working well this week as this Project near completion.
The closer we get to the deadline, the more AutoCAD slows down.
My UCS Icon has disappeared from Modelspace.
It's were it belongs in Paperspace.
The USC Icon is set to "Noorigin" and the color is set to RED for Modelspace.
I need it to orient the many angled spaces we have in this Plan.
In the plot dialog box the options Plot paperspace last and Hide paperspace objects are only supposed to be available in Paperspace however they show up as checked in some of our drawings when plotting from Modelspace. They should be greyed out then. (see attached) If I copy/paste all objects into a new drawing everything is fine. If I delete all layout tabs the options are still checked when plotting in model space.
The only thing I can figure is there are paperspace entities in my model space or that somehow paperspace is leaking through into modelspace.
I'm having a little problem with the modelspace in a vport disappearing on me.
I am trying to do some B.O.M. work, and sometimes I can't snap to a particular point/object, so I turn osnap off and zoom in to identify the correct object. After a certain point in the zoom the drawing regens and then the modelspace disappears completely.
I tried a regenall, closing the drawing and starting it up again, but it's still not there. I checked the properties and it still says it's a vport. When I double click it to enter modelspace from the vport it doesn't take me into modelspace.
I've checked my maxactvp, that's maxed out at 64. I've run an audit and that didn't work.
AutoCAD Civil 3D 2011 32-bit
Win XP Pro SP3
Dual Core, 4 GB of RAM
NVIDIA Quadro FX3700
Since I installed 2010, I noticed that OSNAP seems to want to snap to objects in model space that are outside of the viewport while I am in paper space. It seems to only happen with polygonal viewports.
View 7 Replies View RelatedI have a floor plan xreffed into model space, visretain=1 and i can see the room numbers. I switch to paperspace and go to layer properties and highlight all layers and then turn on all layers in he drawing and thaw in all three columns and still the room numbers do not show. The layer listed in model space is on and thawed. Why won't it show?
View 2 Replies View RelatedMy modelspace is showing thru my wipeouts... But the wipeouts are active and I have remade the viewports with the same result. I've used draw order with no change. And here's the kicker. It (the Wipeout) hides the viewport frame, but not the actual model space material being shown thru the viewport. It remains visible.
View 6 Replies View RelatedIn ModelSpace, when I drag the crosshairs over to the right edge of the screen, the crosshairs will vanish and reappear on the left side of the screen. This is a major problem: If I am reaching for an object off to the right and overshoot with the mouse a little, the crosshairs will suddenly be way over on the left. But much worse than this, I have a toolbar oriented vertically on the right side of the screen. I literally cannot get to that toolbar because the crosshairs swap over to the left side of the screen, instead of changing over to an arrow cursor to make use of the menus.
View 2 Replies View RelatedI was curious if there is a way to lock a specific attributes contents in autocad 2012. I have an attribute with a field inserted that I don't want people to be able to change. If this is possible
View 2 Replies View RelatedIs it possible to export the contents Table directly into Excell from AutoCad2012?
I've tried the Data extraction wizard but it seems to export the Table attributes/properties and not the contents of the table.
I am creating some table of contents. The first column contains symbols that are inserted blocks. Now, when I've created dynamic blocks I've made them to have more visibility states. If I insert the block that has such states, only the saved state is visible. Is there any way that I can use more visibility states when inserting some block into table.
At the moment the only solution is to insert another simplified block that I've created just for this insertion. That way my blocks library is getting bigger and bigger only because of this. I don't use simplified blocks in my drawings, except for the thingy mentioned above.
I am using autocad arch 64 bit on win 7 and am having problems switching out of xref classic so that the newer xref dialog comes up. i edited the SDI but then i cant close a drawing and opening creates more problems.
is there a way to get the xref dialog back?
(Again) Switching the “data type” of the cell,I’m not sure why the AutoCAD doesn't allow changing the “data type” of the cell in the table for already existing data. For example, in the attached table, I wanted to switch the “data type” from “decimal number” to “percentages”, but sounds that the AutoCAD doesn’t allow this function.
In the Excel, for example, we can switch the “data type” easily by selecting the target cells and choosing the format we need! Quite simple, in the AutoCAD, it seems that it needs some work around!
When I work in large files (10,000 kb +) I experience significant delays when copying large amounts of information (copy a floor plan) or when switching between layouts or saving the dwg. I wish I could tell you it started right after I But I just recently started working with the larger files. So this could have been an issue from the time I bough the machine - 18 months ago.
it's either an issue with my graphics card or processor. I would like others to comment on their opinions on adjust my set-up to be more efficient
I believe I have the most current driver for the video card. Did I hear right somewhere that there is no good driver for the Quadro 4000 to work with 2012?
i have a test drawing attached with layout 1 and layout 2.
from model to layout 1 takes 2-3 seconds on my crappy computer, from model to layout 2 takes 8-10 seconds on the same crappy computer.
this sample i attached has a xref binded. which result is the same 3 and 8 seconds respectively.
you may think this is not a big deal. but layout 1 will take 10 seconds to to switch to if you have 5 xref while layout 2 will take a minute.
i did my research and haven't find the difference in variables between the two paperspace layouts.
tried all the variables made no difference:
psltscale, msltscale, celtscale, savefidelity, etc.
also set both viewoprts to undefined same thing.
the only difference is "1" is created from a blank autocad template by selecting "metric - no template", and "2" is imported from a civil 3d dwg after done a plan/profile production and that thing created that layout.
is there a tool to compare all variables between 2 layouts and find the differences? i am certain the problem lie within system variables.
Civil 3D 2012
Work: Xeon W3503, 12GB, Quadro 2000, Dell P2211H x 2
Home: 3930k, 12GB, GTX 590, U3011, QX2710
When switching from layout to model space, and back again, and when switching layouts the regen is slow to an extreme, upwards of (3) minutes. Using Renenall in layout, the regens are quite slow as well. Windows 7, AutoCAD 2011, NVIDIA Quadro FX1800, most current driver.
Additionally, when publishing, the regens are equally slow. LAYOUTREGENCTL setting seems to have no affect.
Switching the “hatch” to be “associative” gives “not applicable”!
I’m wondering why as I choose the “yes” for the “associative” property of the “hatch” then this gives “not applicable” as shown in the screenshot below
What might be the reason?
I have a delay when switching back and forth between model space viewports,
View 7 Replies View RelatedWhen using the undo command, plotting or switching between drawings in Autocad 2010 and now also 2011 I am experiencing long delays of up to 15-20 seconds at a time which is rather frustrating. I am running a fast spec computer and can't seem to overcome it, I haven't had the problem with 2009 and when need to do something quickly have found myself using the outdated software. Other users in the same office have equal or lesser spec computers and are not having the same issues, I have tried a re-install and this hasn't worked either. I was hoping the new 2011 version would solve this issue but no luck.
View 9 Replies View RelatedI'd like to know how to align an object in model space with the edge of my viewport in paperspace.
When I draw, I like to lay out multiple complete drawings in model space, make an appropriately scaled bounding box around them, and then snap a view port to the bounding box in my layout. I usually have multiple drawings lined up in a row in modelspace, so when I want a new layout I do a Save As and then pan around in my viewport to find the next bounding box, at which point I have to resize the viewport to get it to snap to the edges nicely. I really want to be able to to it the otehr way around- while panning I'd like to be able to grab a corner of my modelspace bouding box and snap it to the the corresponding corner of my viewport window. That way making new layouts would be a snap. Is there a way to do this in AutoCAD 2012 LT?
i have in model one drawing, in layout i have 4 viewports, each have different scale, now.. how can i using same model and 1 layout to determine scale of dimentions per each viewport? or all viewports in same layout have same scale of dimention?
View 5 Replies View RelatedI have a problem with one specific drawing where I have created a right viewport; however, if I double click in the port to enter model space, the viewport automatically changes to a top view. If the viewport is locked, no change to the view. This problem only exhibits itself in one drawing so it must be some setting that is drawing specific.
View 1 Replies View Related
