We are using structural steel framing familiies which are sloping in section. Where the view range cuts, the framing does not and the entire member is visible including above the cut plane.
The members are set to cut in plan in "Visiilbity Settings." The view is set to "Fine."
I am having trouble creating my own column and beam
structural column schedule
structural framing schedule
i do not know the settings to be ticked for me to create the schedules and make them appear after i create new scheduling...
also i want to know how the graphical column and beam works...
then setting the level in the schedule to make them reflect instead of using the comments section...
Attach here is a screenshot of the levels...
I just discovered the rafter framing extensions for revit. It is very handy but at places where there is a hip/valley the rafters are shown until the hip/valley. at all the other places (where there are ridges) they are cut at the place where the roof is cut.
I found another thread where they say to change the visibility settings of the rafter family what I already did before but it does not change anything in my floor plan.
How do I show rafters connected to the ridge beam on a framing plan? How to show collar ties on this framing plan or section?
View 3 Replies View RelatedI was following a tutorial when he created a structural plan where he'd place his footings. when i tried it on my Revit Architecture 2014, i found out that i didn't have that feature. is there any way i can turn it on?
i'm not sure if he's using revit architecture because he just refers to it as Revit 2014. i made a floor plan below the 0 mark but things will be tidier if i could make structural plan views.
I am doing a five stories building and when ad the structural column with concrete cast in place material, the representation in plan view does not cover the block hatch of the wall. See attached image. I have read all about structural columns and did not find any solution.
View 5 Replies View RelatedI am creating a dynamic block to do details for structural framing. Attached is an example that I am stuck on. the widget plan and end plan went pretty good. But when I got to creating a cope on the ends I got stuck. I am attempting to stretch the required cope as you can see in my attached drawing. For some reason I can not get the end line to move with the horizontal cope line.
View 4 Replies View RelatedThe Cut Plane in a Plan View doesn't really represent the cut component but instead some kind of projection.In my case, I use a lot of Face Based Windows and Doors since my walls are often slanted. The Plan View representation of these components doesn't look right. A workaround is placing these components in a Component/Model in Place environment.
View 3 Replies View RelatedHow do I get to the settings that control what does and does not show in any given discipline - we need to update the Structural Discipline to show the non-structural walls, and non-structural portions of other walls as halftone.
View 2 Replies View RelatedI have done my studs for my wood frame, However, under blocking, when I tick "generate horizontal elements" and select OK, it tells me that there are identical instances in the same place, this will result in double counting in schedules.
View 1 Replies View RelatedI am working in a project where I need to represent the reflecting ceiling edges in the plan view. I put the first floor plan as underlay, and selected the RCP projection but I don't see the dropped ceiling lines to select them with the linework command. I have done every thing possible with the view range but I don't see the lines.
View 7 Replies View RelatedIn my 3D View my walls disappear when I de-select the structural box. Although drawn as regular walls they are store front panels so carry no load other than their own weight. My Visibility Graphics dialog box seems to have limited options for this. Am I missing something? How do I get them to re-appear in my 3D View for rendering without switching them to a structural wall?
View 2 Replies View RelatedI am doing the structural frame of a house with curved walls and I needed to use the Model in Place command to create a curve shaped column. I defined it's category as Structural Column, but it takes the fill pattern of the wall. When I isolate the column, it has the same fill pattern as the column from the library. I need that the column will be displayed as the other structural column.
View 1 Replies View RelatedHow can I switch the orientation of a structural system placed on a tilted face. In other words, I have framing that snaps to the underside, and I need it flipped to the topside of the face.
View 5 Replies View RelatedStructural columns are exported as blocks to DWG, even if I have checked the "Always export as geometry" -box in the column family.
View 6 Replies View RelatedI working on a project in Revit Architecture and I have the Mechanical (MEP) and Structural (Structure) models linked into my model. I need to reference a detail in the structural model/sheet set. Is there a way to do that without creating a false callout tag with linework?
View 1 Replies View Related1) Why structural columns don't show up in architectural plans. The only way I can see to coordinate the structure with the architectural elements is to use structural plans.
2) How to make structural columns visible in architectural plans? I've tried the visibility graphics but everything seems to be turned on by default.
I'd like to change the line thickness of these structural columns, but changing the view graphics doesn't override.
View 3 Replies View Relatedhow to change the demolished and temporary appearances of non-structural elements such as railiings, plumbing fixtures etc?It is straigh forward to use phase overides to change the appearance of Walls etc that are either demolished or temporary, but however you change these appearances non structural elements stubbornly remain with a dotted blue outline. I want demolished railings and other non-structural elements to appear with a red hidden line style but have been unable to find out how this can done.
View 2 Replies View RelatedRevit Architecture 2014? I've been trying to use the structural beam system, but when I select the joist I cannot select the start/end extension in the properties dialog box. I would like to know why is that?
View 1 Replies View RelatedHow I can successfully import a 3d .dwg model into Revit so I can cut through it in plan and section? I built the model in sketchup, exported it as a .dwg, then impoorted this .dwg into a new Revit family. I then loaded this family into the revit file I'm working in. Its cuts through the model on basement and ground floor plans but not on 2nd or attic. For the 2nd or attic it just shows me the roof of my model.
View 9 Replies View RelatedI'm having trouble editing a family I've made. It's a profiled rim for a crate that needs room for a latch. So I need to create a small spacing in the rim so that the latch can fit. I've tried to cut geometry, and edit the family (rim) itself, but I need to edit it in an elevation view and not floor plan.
View 1 Replies View Relatedbreaking wall section views ? ie. using the section view tool works very well for a BIM wall type, but how can we cut the section so we don't need to have the view show the entire height, etc of the wall. especially when fitting in representative sections of twenty different wall types/situations on a single sheet ?
View 2 Replies View RelatedWhen adding an element, say a door, to something like a wall, if there is a void within the door and everything is set properly to cut out a section of the wall, what is the resultant material colour that you see at the cut?
I've been trying this out and in the Realistic display mode, when I have a door with a recess profile around the frame, in brick I see the brick colour, but in plaster I see a grey which isn't the same as the default plaster colour?
The recess is 12mm into 12.5mm plaster.
What would be possible reason for a void not having any effect on cutting an object? I created a parametric void.Then I created an object.No change to the object. If I create an object then a void, it seems to work.
View 1 Replies View RelatedI have inserted a recess paper towel dispenser into an interior wall. Then a 1/8" tile wall was added in front of the hosting interior wall. The opening for the recess dispenser only cut into the interior hosting wall, not the tile wall. I tried joining the two walls, but it didn't seems to have any effect. Is there any reason why the walls won't join?
View 4 Replies View RelatedI made the building, and after I had to change the elevation levels, and after I did this, I copyed some furniture from the level 1, to the level 2. Some of the furniture was copyed the right way, but all the chairs from the plan are missing. I tought maybe they've been deletel, but I try put new chairs, and they also don't appear in the second level only. When I went to 3D view, i saw there are there, at the right level where they should be. I dont know why they don't appear in plan. And also I noticed the interior walls are grey, and not white in the plan. Also, when I go to ground floor, and put underlay level 1, I see the chairs there in the underlay, not at level 2. I made this print screen maybe is easyer to understand. [URL]
View 2 Replies View RelatedI want to turn my in-place mass walls (sloped or helical) to structural walls but i don't know how to do it. I'm able to do the walls but when i switch it to the analytical view the wall doesn't appear because it's not structural. It's there a way to do in-place mass structural walls.
View 1 Replies View RelatedI am cutting a dormer in a roof with a square rafter cut. I want the dormer to be plumb cut. Is there any way to do this? The property seems to be set for the entire roof.
View 3 Replies View RelatedQuestion #1: To my Sections Sheet, I am adding a Key Plan of each floor to show where the sections are cut. I duplicated a plan of each floor and renamed it "Floor # - Key Plan", and added the view to the Sections Sheet at a small scale, and now I am using a 1" = 80'-" scale for these key plans. I am able to hide all the unwanted annotations elements, but I notice that some like the "UP" and "DN" of stairs, which are very large, do not go away without erasing the stairs also.
How can I leave the stairs at this small scale but without the associated annotation?
(I also notice that this happens with elements like Washer (W), the Water Heater (WH), etc).
Question # 2. Related question: Do Revit has a "Key Plan" creation fuction to automate this work?
I have a renovation project that I have entered the building in a existing phase. I used the demolition tool to show work removed on a demo plan. I created a new construction plan and set the phase to "New Construction and the phase filter to "Show previous + new" . The problem is that all work to be demolished appears as existing and new work appears on the demo plan as existing.
View 2 Replies View Related
