I can't seem to find any sloping reference plane I have inserted as a Top Constraint for a wall I want to draw under it. How to make that happen? The only Constraints visible are Levels and Levels only appear to allow themselves to be draw exactly horizontally.
View 5 RepliesI am trying to lock a reference plane to a wall location. Is this possible? I want to move the reference plane and the wall follow. I keep having people who want to make the building bigger.
View 1 Replies View RelatedHow We can to change the default height Ceiling plane In Project Browser.
For example, the Default is 2600mm.
I want to Over 2800mm set.
Not in Time Drawing Ceiling.
When we draw a reference plane in a project in the Level 1 (0' 0" Elevation) then the reference plane elevation shows 4’ 0” in the Specify Shared Coordinates Tab. Why the elevation of reference plane shows the 4’ 0” height? Is it default elevation for reference plane?
See the attached jpg .
I had this working just fine, then made some changes (including deleting some reference planes) and now I can't get it to work. I need to lock a diagonal reference plane to the intersection of 2 orthogonal reference planes, so that my door (on an angle) will slide toward the fixed corner, instead of the corner moving toward the door. It must be something simple I did the first time that I'm just not thinking of this time around...
View 5 Replies View RelatedIn Revit 2012, how do I place a wall at an angle to the ground plane, so it can be connected to a roof above? I have tried placing a wall on level and rotating it, however it does not appear to work. I can rotate other elements, but not walls.
View 1 Replies View RelatedI have developed a family-construction method that combines equipment with its dedicated electrical receptacles. It is designed such that once inserted, the user can drag the outlet symbol and outlet to the right or left and also move the outlet symbol away from the wall plane to permit symbol stacking in plan. Most of the time this works but on some families, though seeming constructed in the same manner, the link between the receptacle and the controlling plane gets broken. The link to the outlet annotation family always stays connected.
I've attached a Revit project contain two families, one that works and one that does not.
I am new to Revit architecture and in the process of learning the software. How do I create a roof walkway for a sloping roof. these walkways are for people to be able to securely walk on the roof for maintainance of mechanical equipment fitted on the roof. Of the walkway will be along the gradient of the roof.
View 1 Replies View RelatedIs there now a standard procedure to create a sloping driveway in Revit ??
View 3 Replies View RelatedWhen adding constrains in dynamic block I do get error: "The constraint cannot be applied. The two objects must reside in the same plane".
How could I get both of the objects on the same plane? Don't have a lot of experience whit AutoCad 3d though...
Any way to get a wall sweep that's set up in the type/structure properties to follow a wall if that walls profile has changed. For example, in the image below, I've split the wall and adjusted it's profile to create some cheesy angled parapet. How do i get my wall cap to follow along? I thought splitting it and changing it's height would work, but no. And if I change the profile without splitting the wall the wall cap just runs right through the wall, as if the profiel was never even changed.
View 3 Replies View RelatedI have to draw a bulkhead wall that connects to a full height wall and a gyp bd ceiling. This causes the entire end of the full height wall to skew in line with the butt joint above the ceiling level. I tried Wall Joins but all the options screw up the bottom half of the wall which needs to remain in line with the paired opposite. I also tried editing the sketch of the wall profile but Revit couldn't keep the elements joined. I tried trimming the two walls back together afterwards but the wall profile dominates and prevents a clean join above the ceiling.
Surely there's a way to have different kinds of joins at different heights?
I am trying to align the curtain wall with the edge of the concrete slab/face of wood framed wall (Core). I have tried to align and move however the whole wall moves as well as the edge of the slab. How I can move the Curtain wall leaving the other elements in place?
View 2 Replies View RelatedRefer to the attached file. How can I cut the RED part of the Wall 1 (W1) , where Wall 2 is sloped. I also want to cut a hole in wall 2 (W2) by the BLUE rectangle , but why I can't do that .
I also want to add a second floor to my project but I can only see the" Level" icon goes grey and I can't click it.
I have set up a plane on whicg I have a referance image that I will base my model on. The problem is I can't see image after I start to block it out. When I turn wireframe on the image disapears?
How to I see referance plane image and have the rest in wireframe?
When I try to change the length of a wall it grows at both end. How to grow at one end only?
When I change the wall type to one with a different thickness, I cannot control which face of the wall remains fixed and which face moves. eg: change from 130mm to 250mm screws up my room width. How do I do this?
I am trying to make a floorplan of my house in Revit 2013, but I am having an issue when it comes to one wall in my house. I have an opening in the Master Bedroom that leads to the bathroom. This wall has a weird arched-like opening in it and I have no clue how to make this in Revit. I have attached a sketch.
Also, my exterior walls are 7' tall but the interior walls start at 7' and go up to 8' once in the middle of the house and reduce back to 7". How does one set that up in Revit?
EDIT: May have made the image too small to see, but the top is not arched, it is actually half of a decagon.
I have a question about wall profiles. I want to make a profile on a wall so I can make Zinc Panels on the wall that are 10" X 20". I've attached a picture of what I'm going for. I'd like it to have a 1/2" spacing between them and with a joint depth of 1" and I'd like to do this is the wall type so that I can use this wall in multiple places rather than having it model-in-place. Anyway I have made a profile that is 1" X 10" so that it can become my panel profile. But when I go to add it to the wall as a wall sweep as I have seen people do I get hung up on how to make it tile up the wall and also I don't understand how to make the profile so that it is 20" wide. I have a screen shot of where I'm editing this too. Below is the link of the site.
View 8 Replies View RelatedIs there a setting to export the grid lines of ACT ceiling in a 3D view to DWG?
I don't know if there is because I can't even get the grid lines to show in a 3d view. Right now the view shows the ACT ceiling as a simple geometric shape.
With no luck, I have been trying to figure out how to insert a blank value for ceiling heights in a finish schedule. There are other rooms with blank values, however it appears that rooms that once had a ceiling can no longer have a blank value. From the research I've done it seems the only way to correct this may be to delete and recreate the room.
View 3 Replies View RelatedI read a 2009/10 thread, "Rotating lighting", describing how to work around the problem of family lighting fixture members not rotating. I would hope there is a better solution today.
I simply want to place a lighting fixture - std 2x4 flourescent, on a 7 deg sloped ceiling. The axis of rotation is the long run of the light fixture. Is this not possible in Revit 2013?
Or, do I have to dredge up the work around from 3 releases ago and attempt to discern how to make it work?
It seems like I should just be able to set the family to use a work plane-based assignment and then place it with the correct work plane active. That is not happening. The light fixture doesn't want to rotate the 7 degrees to align with the work plane.
Basic master bedroom with a view. roof has a 9 pitch. I cannot figure out how to put a cathedral ceiling in. How do you?
View 4 Replies View Related“Drag wall end” to the edge of the wall (indicated),In the attached screenshot, I wanted to drag the end of the temporary dimension from its location to the end edge of the wall but sounds not to respond!
How this temporary dimension can be dragged to the edge of the wall?
I am laying out a simple structure. Bearing wall to bearing wall is 35’, with a few non bearing walls between the bearing walls. I will be using a truss to span from bearing wall to bearing wall. What would be the best work flow for the drywall ceiling material. The ceiling seems to require a core element. I cannot seem to manage drywall alone. If I create a ceiling with 2x4 core and drywall finish and create a ceiling over the whole area the ceiling seems to auto dim to the ceiling finish and not the core 2x4. Then there is the issue of the clean up at the top plate were the wall and ceiling finishes meet
View 1 Replies View RelatedI have one of the floors in our building doing something wacky. The 5th floor reflected ceiling plan looks fine so I create detail plans for the suites at a different scale. this new suite blowup has what looks to be the same suite but everything is greyed out and when i switch from coarse detail to fine detail it doesn't do a thing.
The orignal full reflected ceiling plan looks fine. The line are black. The detail swithces back and forth... I can;t figure out what the problem could be. I used the same process on other floor and everyting is OK. The View Ranges are the same and everthing else in the properties seem the same too.
I have a problem. The linked model from our electrical engineer its lights are at the correct height but the ACT ceiling is still running its lines throiugh the lights. how do we take care of this to where the linked model which has the lights in it cut through our ACT ceiling from our central model?
View 2 Replies View RelatedI'm using Revit 2014 & have not been able to fade the ceiling grid lines so they don't plot out so heavy on my dwgs. I've tried overriding graphics of these grids with half tone which didn't work then I tried transparency & that did not work. They either stay on or turn right off!
View 4 Replies View RelatedAre there any plans to add the simple yet productive feature of moving an object in the X and Y directions at the same time?Also, I would love to be able to select the ceiling grid and hit the space bar and have the grid rotate 90 degrees.
View 4 Replies View RelatedI'm use to working with autocad layers.In AutoCAD if I'm drawing electrical plan and floor plan, HVAC...ect I just freeze in viewport the things I don't want to see for that particurler sheet.
In Revit I duplicated my floor plan to create my electrical plan. I can add my recepticals and switchs but it won't let me add light fixture. Do I add the light fixture to ceiling plan then some how move them to my electrical plan?
How can I move my air vents to the ceiling plan from the floor plan ?
View 1 Replies View RelatedI have fixtures on the reflected ceiling plan showing up in the foundation. How to stop this
View 1 Replies View Related