experiencing monolithic stair with top tread missing - see attached image. The plan has irregular treads and I did pull the top riser line away from the boundary intersection but it had not affect.Or is this just a "feature"
View 3 Replies
Stair tread number tool is wonderful. BUT it is being not printed properly.
Example image attached:
- 'on screen' on the left is taken from my screen. The numbers are shown correctly.
- 'after print' in the middle is a black&white pdf print by adobe pdf. you can see there is the last number missing.
- 'after print-random number missing' on the right is a coloured pdf print also by adobe pdf. several numbers are missing and it happened randomly.
I have made a stair by sketch, an u-shaped one. I do have some problems with the 3d model. it will not show up correctly. I add some print screens and you can see.
View 3 Replies View RelatedI use all the time L shape and U shape winder stairs in combination with the Monolithic Type.
We use to concrete the monolithic part of the stairs and then dress the stairs with treads and risers. The new tool looks that working very nice.
So OK I draw the U shape winder stair and of course i want to construct the stairs.
I want to prepape a detail plan view with dimensions only for the Monolithic Part (Concrete) of the stair but i can't find a way to dispay only the monolithic part without Treads and Riser.It is possible in 3d view but no in plan view. The news tool that calculate winder stairs is "half job done" if i can't print with dimension the concrete part of the winder stairs.
My stairs go from Level 1 to 2 and join a concrete floor at level 2.
The stairs are monolithic.
The problem I have is that at the top of the stairs the end riser can be seen and so it appears as an extra tread when viewed in plan.
See attached file, the red cross marks the lines which I need to remove.
I cannot join the stairs to the slab.
How can I remove these lines - is there something better than a masking region? can I set something in the family?
What is a good way to finish up the monolithic stairs?
- How can I join the top tread to the upper floor slab? (red circle in attached sketch)
- And is there a way to join the CIP monolithic stairs to the CIP walls? (blue circles)
I am trying to extend a stair stringer past the start of the stair tread. See attached file. I can't seem to get it. What am I missing?
View 1 Replies View RelatedI can't get Revit to display the cut material of a stair (landing or run) in 2013 using the new stairs... i have tried different settings in object styles, visibility/graphics, materials, details levels, phasing all without success.
Successfully show material cut pattern on a stair in section?
In the attached i have the new "Component" stair next to the old style "By Sketch" stair, the sketch stair shows the cut pattern the component one does not, this is the same section view not two sections.
my Stair label text "UP" in my stair.In my properties browser its already checked but still didn't showed up.Anything i need to set?
View 1 Replies View RelatedI have a client that needed to know the distance required to make a stair case, and when I drew it wight revit 2013, I discovered that I could manually adjust the riser height but was unable to adjust the tread length. I was also unable to end the stairs with a tread rather than a riser, witch he wanted.
View 1 Replies View RelatedI am having a problem adding a top landing to an external staircase. see below image.
Every time i try and add the top landing i either get boundary error messages or railings surround top landing.
Is it possible to create a Stair Tag with the pitch reported? I have a tag which includes the number and height of rises as well as the size of treads but I would like to include the pitch also. Obviously this would use the dimensions of the rise and tread in the formula Tan X = Rise/Tread, but how do I create this in a tag? I have looked at using a Reporting Parameter but every time I read the Wikihelp paragraph on them my eyes just glaze over as I cannot follow it at all but it does mention formulas....
View 8 Replies View RelatedJust Starting with new Revit LT 2013(The Comparison chart from Autodesk lists the differences between LT and Full Revit as no Massing, Rendering and no multi user collaboration) Everything else should be the same!
I'm using 'LT_USI_Residential-Default' Template for my project.In the Stair Family, I have a few options, but not the '7"max riser 11" tread' stair that is available in other Templates.Is there a way to bring that Stair Family into the Template?
Maybe I don't know the 'workarounds', but none of the Stairs available in the above Template have changeable 'width' parameter under 'Dimensions' in the properties window.No matter what I do, all Stairs are first drawn 4' wide, and then I have to edit the width, but it's a pain since I get bunch of error messages and Landings often can't complete and needed to be manually added later.Even though the Type Properties list all stairs widths as 3' min., they still all draw as 4'.What's wrong with these Stairs?
How can I make the bottom of stair to flat instead of steps?
View 5 Replies View RelatedIs the any way of saving settings for in particular base level and top level. Always defaults to the current view level for base - can this be overriden permanently. Same for upper level - what lvel does it automatically default. Stair by sketch often involves trial and error and redoing it each time because once done you cant change the levels, rise, width or change the number of segments governed by the path. It would be nice to not have to reset levels each time.
View 1 Replies View RelatedIs there a way to change the elevation of the cut line for an individual stair without changing the cut line for the entire view? The only way I know change the cut line is thru View Properties > View Range > Cut Plane.
View 7 Replies View RelatedHow to show the sequential numbers on the steps of stair?
I’m wondering if there is a way to show the sequential number on the steps of stair.
Also, we are all the time required to write the number of stairs, run length and rise length on the drawing. Is this possible in the Revit?
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
Can sweep profile cut up to the bottom of stair stringer?
Find attached.
I currently have a situation in white my stair handrail mid post wont connect to my stair stringer. I have a C10 stair stringer and am using a modified typer square handrail system I have made. I am sure there is a setting or preference I have missed that is causing this. I have attached an image for reference.
ALSO in the image you can see the top rail does not fully attach to the end post. It sits in the middle somehow. AND that end post sits halfway off the stringer.
if this is easy, but how do I calculate the volume of concrete needed to pour a cast-in-place spiral stair?
View 1 Replies View RelatedI have a problem where I am unsure if my upgraded template is incompatible with Revit 2013 or is there something else at play.
If I create a precast stair in default template I get "end with riser" turned on automaticaly. If I copy that stair to my template and create new stair, "end with riser" is turned off and I manually have to adjust stair afterwards.
Problem is "end with riser" is now an instance parameter of stairs and I can't find where to change the default value.
Why is the stair type that works in default template stuffed when copied to my template?
I need to know how to eliminate my first tread being part of the landing. I have tried every possible combination of varibles I can find. It happens randomly. when it does if I adjust anything it comes back.
View 4 Replies View RelatedHow to make the tire tread texture in the photo link below ? I need a square texture of this type of tire tread to use in a 3D modeling program. I need to map the texture to the mesh of a 3D tire.
Attached Thumbnails
I've been trying to create a stair block that will automatically adjust the riser height to to suit the total vertical rise of the flight, but am having issues.
I drew two 'tread/riser' Plines, and constrained the daylights out of them. By stretching the grip for the 'Total Rise' constraint, the risers adjust nicely, while the treads remain at their desired 11" depth.
My problem is that when I try to create an array of the tread/riser, (using a linear parameter aligned with the slope of the stair) I can't get the 'column' width to change as the risers change height. Instead the value remains constant, and the arrayed copies don't connect with each other.
Any way either to fix this so that that the copies connect 'head-to-tail'?
We have created a number of project parameters (all ifc parameters)
Site Name
Building
Floor
Space Number
Space Type
And Mark Test, Yes another test, As identity data.
We can schedule out all the information with no issues, however when we export to ifc we can only find the “Test” information. Are we missing a setting in the export or have we create the project parameter up incorrectly.
I am using 2014 Revit and have some problem with the exported AutoCAD layers from Revit.
My project has 3 levels and I exported the floor plans from Revit. Ground level and third level have all the elements like shown Revit, but the second floor plan doesn't show certain catagory items like columns. I already tried to create new level for the second floor plan, but the exported result is the same. I am not sure if there is any setting to control the layer visibility when it is being exported.
I am trying to create a sidewalk area that has a 45 degree 8'x8' hatch pattern in the model. It shows up in 3D but not 2D. What is the problem? It needs to show up in my plans. I have the same problem getting floors to show surface patterns too. Using Revit 2011. A friend gets it to work on his computer with the same version.
View 2 Replies View Relatedi just started working with Revit Architecture 2013 and im doing this tutorial for a basig design but at one point it says go to Massing & Site tab in the ribbon, and it's just not there?
View 5 Replies View RelatedI noticed that I don't have (ELEVATIONS) tab and also (elevation icon). See the picture. Also (Elevation Marks) in the window view are not exist.How can I regain all these?
View 6 Replies View RelatedAll of a sudden when I go into sketch mode, I can no longer see a tool bar giving me the sketch tool options. The same is true for editing or creating a fill region.
View 1 Replies View RelatedEvery so often while i'm working in Revit the Ribbon/panel bottoms disappear. Even when toggling threw the options i can only get some of it to reappear. I attached what it looks like and when i toggle through the options.
View 1 Replies View Related
