I have inherited some Revit files, all of which have a ground floor and ceiling plan (hence an associated level).
The levels do not show the in elevations (or sections for that matter). It is not a view setting, I have checked this, nor are they hidden by category or element. I have added new levels and these are visible. The levels exist, I just cannot view them or select them.
In starting a new project, I renamed "Level 1" to "Street Level" and "Level 2" to "Level 1". Next I added two additional levels in the drawing, "Level 2" and "Level 3".
My Project Browser shows only Level 1, Site, and Street. Why do the Levels 2 and 3 not show under and how can I get them to.
why have the levels not showing up on all of the elevations even when I adjust the drawing viewport??
View 1 Replies View RelatedMy concern is regarding a louvre family i am placing on walls in a multi-storey commercial project. They are viewable in 3d mode and Floor plan view but when i switch to elevation, all i get are holes in the walls where the louvre should be sitting. This louvre family is from Breezway and i am getting the same result with all Breezway family members i have downloaded.
View 4 Replies View RelatedHow can I fixing ( for example) attachment DWG contains too many elevation levels for ( Lines, Dim, Text & Layers) quickly, from all elevation levels into zero elevation level.
To explain more : When I am looking on top view it's good plan, but when I am looking on other Isometric view it's shown many levels . I need to fix every things quickly to zero level ?
I am working with revit since 08, and there was this little annoying bug - in the middle of working process some levels become super slow - adding walls becomes a big task. At the beginning everything works great, but (I suspect) at some point I add curtain inside the room, something goes wrong and the level becomes slow.
It does not work even if I remove curtain walls or purge unused or duplicate window or make separate plan view - if floor area with several basic walls is visible level becomes slow.
We don not show CL profiles and only show the gutters on the CL profile view. We also do not used profile bands.
I need to show Superelevation on both left and right profiles complete with labeling.
Short of creating a seperate alignment for each, sampling the corridor surface, superimposing it onto the CL profile view and then creating a layout profile by drawing over the sampled surface.
I closed the 'levels' dialog box on the left hand side of the screen (underneath the 'properties' dock and for the life of me cannot figure out how to get it back.
View 3 Replies View RelatedDo I have to use the Stack Walls family in order to have my walls line up on top of each other between the levels? My walls are all slightly off in 3D view and look messy..
View 3 Replies View RelatedIs there any way of adjusting the text on a level?
View 2 Replies View RelatedI have created new levels e.g T.O.F. & T.O.G. but they will not show up under the existing Floor Plans section in the Browser. All I get is a new section Titled: ???! How do I get these new levels to show with the rest of my levels under the floor plans category. Using Revit Ultimate 2014.
View 2 Replies View RelatedI need to swap my level 1 and level 2 of my building's floorplans. What is the most efficient way to take the walls etc. from level two and place them on level 1, and take whats on level 1 and place them on level 2? I am swapping the floorplans.
View 2 Replies View Relatedhow to create a wall that infills the gable between two levels of the same roof. There is no internal wall below this location - so this would be some sort of lightweight studwork and panelling rather than brick.
Infrastructure Design Suite Premium 2014
Self-built i7-3930K, 16Gb RAM, P9X79 m/board
SSD(system), HDD(data), Win7Pro64, Quadro K4000
“Aligned to selected levels” is not active,
I’m wondering why the option “aligned to selected levels” is not active as I copy and paste from one level to another.
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
Is there a way to list what items are constrained to levels? i need to remove a couple of annoying levels but have a feeling that walls, roofs, families, etc may be constrained to the levels that I need to delete.
I tried doing a multi-category schedule but I think I need to do one for doors, windows, etc. I thought I read somewhere that this feature was available in Revit 2012.
I can't figure out how to get my levels to show fractions of inches. I can add a dimension from level to level and see the fraction, but the level itself insists on rounding to nearest inch. View scale makes no difference.
View 2 Replies View RelatedWe are developing a multistory housing project that will have 5 unique unit plans. What I would like to know is the best approach to implimenting the unit plans in revit?
In autocad, we would create an xref of the unit, then xref as needed on base plans. Thus the ability to place multiple xrefs of the unit on various levels while maintatining the ability to make one change to the original unit plan and have it update thru out the project....How would we do this in Revit?
How to I change the Comma to a Period in Levels or Dimensions?
View 2 Replies View RelatedHaving some very strange issues with area boundaries used in groups.
I have tested it in RAC 2011, 2012 and 2013 and they all seem to be doing similar things.
grouping them and pasting them is fine - even between levels and even schemes. when i edit them items are excluded on sketch close and even disappear from one scheme to only appear in the scheme that i edited them in. the area still remains in both but only boundaries in one scheme.
How to get the brick hatch pattern on my elevations to line up between levels. I have a two story residence with one wall the front that has brick all the up to the roof (the rest of the house has cement board side on the second story). My problem is that the brick pattern on the second floor wall does not line up with the brick pattern on the first floor.
I tried to just extend the first floor wall up to the roof, but I did not like how it wrapped around the corner of the second floor to tie in with the siding. Surely theres is a way to set the hatch patterns origin like in ACA so that all the bricks line up nice and pretty. Also would lining up the brick pattern on the quoins, which are, whatchamacallums... in-place-edit components?
We are looking for a way to document the free height, between two floor slab on two different levels, on our floorplans. We would like to use some sort of tag. And not just text.
View 9 Replies View RelatedI started a new project. I linked a revit file. I copy monitored key levels from the linked file. The color of the level heads is black and this indicates that there are no associated plan views. My question is, what is the best way to create plan views from the copy monitored levels?
View 1 Replies View RelatedThere is a way of controlling how much some objetcs extend outside the scope box? The levels, sections and grids extend too much to my taste and the space avaliable in my sheet.
View 1 Replies View RelatedI'm currently Building a Library Technology Hub that has 3 story atrium. I'm trying to create a 3d camera view that shows the multiple levels that open to the atrium. However, only the 1st floor and mezanine floor (within 1st floor ceiling heights) are in my 3d view. The rendred view shows as if I have a solid ceiling across the entire 1st floor. I am almost positive that this is an issue with my camera settings since my 2nd and 3rd floors are cut around the atrium opening. I have clicked on almost every option in my properties menu and am at a loss!
Just btw, I'm an intermediate level, self-taught revit user (I have used it on a daily basis for about a year now). I'm no guru, but I'm quite savvy on making things work like I want them to.
I have attached a test render of the space. the "ceiling" should be open above my mezanine, and extend to desk at the right and the lounge seating at the left. However, it has rendered as a single plane.
Is the anyway to keep the body of a custom Elevation tags to stay horizontal as do section tags?
View 7 Replies View RelatedI noticed that I don't have (ELEVATIONS) tab and also (elevation icon). See the picture. Also (Elevation Marks) in the window view are not exist.How can I regain all these?
View 6 Replies View RelatedIs it possible to move an elevation tag in one view and move the same one in another view keeping them in there separate locations?
View 1 Replies View RelatedI am in the process of drawing up an existing building and firstly am setting up with the building mass. I have managed to get the main bodys of the building done and the main roof.The problem now is that when i switch too the east or west elevations to add mass for the roofs on the adjoining wings of the building it wont let me see the model lines when i draw them in the screen i just get an error message " None of the created elements are visible in Elevation: East View. You may want to check the active view, its Parameters, and Visibility settings. "I have my reference line set not far from the building and it seemed fine when i done the roof from the north and south views for the main building. I can see the model lines when i switch too 3D views but i cant create the mass from there.
View 4 Replies View RelatedHow to visually represent depth in an elevation?
The only answer I've found is to use linework, but that can't be the way to go in a program such as revit. That's the whole point of it, right? To not have to sit and do things manually and then have to change the lines every time something in the building changes. I know that Archicad can show line thickness depending on distance from elevation line. And god do i dislike Archicad, but that's exactly what I'm looking for.
Another answer I've found is to use shadows, but then you get the problem of only being able to print as raster = no sharp lines.
The level lines appear in the east elevation but not the building. The elevation marker tab is blank, unlike the N,W,and S tab.
View 1 Replies View RelatedWhen we draw a reference plane in a project in the Level 1 (0' 0" Elevation) then the reference plane elevation shows 4’ 0” in the Specify Shared Coordinates Tab. Why the elevation of reference plane shows the 4’ 0” height? Is it default elevation for reference plane?
See the attached jpg .