I need to swap my level 1 and level 2 of my building's floorplans. What is the most efficient way to take the walls etc. from level two and place them on level 1, and take whats on level 1 and place them on level 2? I am swapping the floorplans.
View 2 RepliesI am modifying topography to include multiple building pads at varying levels and also including sloped pads. I am having a non-consistent problem at the common boundary of some pads. A small sliver of topography sometimes 'sticks through' the common boundary. The height it sticks through seems arbitary, sometimes to the height of the original topography when cutting and sometimes much higher. I have used the copy/paste aligned commands to ensure the boundaries are exactly common but this does not work.
I have read that some users cut the topography globally and then build up the various levels and ramps using floors and the variable floor thickness command. This seems a bit cumbersome and I imagine would cause problems when cutting sections etc.
I have an existing ground surface with all different z co-ords and im trying to add three proposed buildings to my exisiting ground with all the builidngs having a level of 32.5 as a minimum, however at some points the ground is higher than 32.5 and I only want to raise my existing ground to 32.5 within the proposed buidling layout if it is below 32.5 as im doing a flood calculation. What do i need to for this?
View 2 Replies View RelatedI want to subdivide my Revit building model including its components in many segments. These segments will be carried out one after another in the reality. How can I do that without need to subdivide every component (walls, ceilings....) ?
View 3 Replies View RelatedIn Revit, how can I stretch a building in one direction, including all floors, in either plan or elevation? Let's say a wing of a 3-story building is 20' long, and I want to make it 24' long.
In ACAD, there is the stretch command that uses a fence.
Granted I would have to use stretch on each plan & elevation drawing, but all elements within the fence are sretched.
Do I have to move a grid, and hope that I've locked all walls on all floors to that grid so they move when the grid is moved?
Sometimes I'm unable to place a truss in my building. When I am able to get it in, it's never at the right height (either too high or too low). I've tried moving it in an elevation and section, but it will only move left and right, not up and down. My teacher said something about changing the view range, which I did.
View 1 Replies View RelatedLike in Autocad is there a way to put building elements onto layers to turn off and on when needed?
View 1 Replies View RelatedI have problem when i try to use function analyze mass model in revit building they show message like attached file.
View 1 Replies View RelatedI created a curtain panel family and loaded it into my project where I had created a mass and divided the surface, and changed the panels to be my curtain panel family i created. The mass has a curve that I want the panel to be on the inside of, but the panel is always placed on the outside. File is attached. So on the smaller curve on the north side of my building, the panels are placed on the inside of the building instead of the outside. How can I place the panels on the outside of the building along the curve?
View 3 Replies View RelatedI have a 3 story building. We are almost finished with design development. I need to raise the building's first floor which will cause all the other floors to change their level heights. I have been told that we need to fake in level markers because to change the level heights will cause all the information (for example dimensions) to disappear because they are 'tied' to the original level height. Is there a way to raise the building without loosing all the work that has been done?
View 9 Replies View RelatedI have multiple building pads in a model because I have multiple phases to represent. The problem I'm having is that the pads are cutting the topo surface in all phases. When I check the properties for each pads they all appear to bel properly identified as being created in the appropriate phase and yet there doesn't seem to be any way to turn off the building pad for future work in the existing conditions. See attached image.
I suppose the other possibility is that the pads are not really in the views, but the topo, having been excavated in one view,stays excavated in all views and won't fill in?
how to disable the pads where and when they're not needed? I've tried hiding the pad elements in the views, but that doesn't seem to do anything.
I need to model a building that cascades down a steep sloped hill. Should I create a toposurface first and then model onto that or should I make my model and then apply it to a toposurface?
View 1 Replies View RelatedI'm using Revit 2012.
know of a way to modify both Contour Lines (Topo) and the actual building in the same file?
i.e. without linking the file "topo" to the file "building"?
I am working with revit since 08, and there was this little annoying bug - in the middle of working process some levels become super slow - adding walls becomes a big task. At the beginning everything works great, but (I suspect) at some point I add curtain inside the room, something goes wrong and the level becomes slow.
It does not work even if I remove curtain walls or purge unused or duplicate window or make separate plan view - if floor area with several basic walls is visible level becomes slow.
I seems that SolidWorks Live Building is better than Revit, so I'm going to wait until Autodesk buys it and tell us to forget Revit, as they did with AutoArchitect S8 and more recently with ADT:
[URL]...
[URL]....
I modeled an apartment building with 4 floors, etc, and I'd like to make an exact copy of this building twice, because this area has three identical apartment buildings side by side. How can I do this properly?
View 6 Replies View RelatedI have a highrise that steps inward in various areas. Since I model structural concrete, there are no window walls stopping my depth of view.
Is there an option where I can vary my depth in areas? I don't want to create more views. An option is to halftone the areas that are set and hide walls that are way in the interior, but this is very time consuming. In addition, if I halftone a slab, the slab portions that are not inset turn halftone too, then I have to fix the linework.
See attachment
I am trying to figure out how to change the color of the exterior of my building, which is brick.
View 2 Replies View RelatedI'm trying to export Revit into Navisworks Simulate but there's no Navisworks tool in External tools. I did a full install of the Design Suite and checked Control Panel/ Programs/ Programs and Features for " autodesk navisworks simulate 2013 exporter plugins" but they're not installed. Are the plugins included in the Suite or do I download them from Autodesk?
View 2 Replies View RelatedI am participating in a architectural design draft, regarding renovation of an industrial building. The building is only uploaded in .DWG and .3DS, which presumably means it´s origanally drawn in Auto Cad. But when i link the DWG (ACAD) file to Revit, it treats it like a component making it impossible to edit walls, windows, making cross sections, floor plans, checking room heights etc. Is there anyway i can resolve this problem other than learning how to draw AutoCad better ?
View 2 Replies View RelatedI closed the 'levels' dialog box on the left hand side of the screen (underneath the 'properties' dock and for the life of me cannot figure out how to get it back.
View 3 Replies View RelatedI have inherited some Revit files, all of which have a ground floor and ceiling plan (hence an associated level).
The levels do not show the in elevations (or sections for that matter). It is not a view setting, I have checked this, nor are they hidden by category or element. I have added new levels and these are visible. The levels exist, I just cannot view them or select them.
Do I have to use the Stack Walls family in order to have my walls line up on top of each other between the levels? My walls are all slightly off in 3D view and look messy..
View 3 Replies View Relatedi have an office building designed in Revit and i want to put a Fascia around the top- it just will not work for me!the same to the roof- i want a flat roof, so i did a roof by extrusion and it asks me for workplanes etc?then it tells me this:Extrusion roof sketch must be open. The roof's thickness and material composition are defined in its type.
View 9 Replies View RelatedRegarding a building footprint that is long from south to north and then about 2/3s (two thirds) of the length the footprints turns 45 degrees to the left (making this angle the 135 degree angle of AutoCAD), then I want to create a long Building Section parallel to the building footprint with the bottom 2/3 of the section from south to north and then the last 1/3 of that building section turned 45 degrees to agree with the 1/3 angle of that part of the building.
View 4 Replies View RelatedIs there any way of adjusting the text on a level?
View 2 Replies View RelatedI have created new levels e.g T.O.F. & T.O.G. but they will not show up under the existing Floor Plans section in the Browser. All I get is a new section Titled: ???! How do I get these new levels to show with the rest of my levels under the floor plans category. Using Revit Ultimate 2014.
View 2 Replies View Relatedhow to create a wall that infills the gable between two levels of the same roof. There is no internal wall below this location - so this would be some sort of lightweight studwork and panelling rather than brick.
Infrastructure Design Suite Premium 2014
Self-built i7-3930K, 16Gb RAM, P9X79 m/board
SSD(system), HDD(data), Win7Pro64, Quadro K4000
“Aligned to selected levels” is not active,
I’m wondering why the option “aligned to selected levels” is not active as I copy and paste from one level to another.
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
Is there a way to list what items are constrained to levels? i need to remove a couple of annoying levels but have a feeling that walls, roofs, families, etc may be constrained to the levels that I need to delete.
I tried doing a multi-category schedule but I think I need to do one for doors, windows, etc. I thought I read somewhere that this feature was available in Revit 2012.
I can't figure out how to get my levels to show fractions of inches. I can add a dimension from level to level and see the fraction, but the level itself insists on rounding to nearest inch. View scale makes no difference.
View 2 Replies View Related