What's the best way to create tilt up concrete panels? In the screen grab bellow, I used an extrusion, gave it concrete material, and left a 10mm gap between each panel to create that illusion.
Can this be done as a wall, if so how do I add those gaps/voids?
I am looking to create an irregular concrete slab, with barrel vaulted ceilings on a small radial section of a circular slab, and a a parabolically curved upper section to the slab, and a large punched hole in the middle of the slab. To this point, I have been able to achieve this using multiple components and masses, but I was wondering if there was a way to make a single object with a single solid material that may be able to achieve the same effect. I have attached a section for ease of explanation.
View 8 Replies View RelatedI'm trying to create an adaptive family (a concrete bleacher/bench) that mitres to its adjoining instances when placed in a project (see attached images).
The family is not acting as I intend it to when loaded into the project (bottom right image). I've created six adaptive points which are intended to correspond to refeence points in the project.
I think the problem has to do with the faces of the extrusion, they don't seem to be able to align to an angled reference plane. How the extrusion can expand/contract in a linear fashion and have ends that mitre adaptively?
can we create multiple panels in window (revit2013)
View 1 Replies View RelatedWhat's the best way to create the attached: EQ ashlar panels, and wall sweeps with joints?
View 8 Replies View RelatedI can place a solar panel on the roof, but cannot do anything with it. When I try to tilt it from upright, it turns yellow and says "cannot rotate" . Been stuck on this problem for a week now, and am quite frustrated as you can imagine. Have tried every trick that I and others have suggested to no effect. Seems to be constrained to one of my vertical reference lines. Reference line is listed as the "host", but it's greyed out, so I can't change it. Tried to disassociate from reference line, but can't.
Went in to "family" and noticed that there's and extrusion underneath the panel (invisible when placing the panel). Don't know what it's there for, or if this has anything to do with it. I can't delete or modify it.
I've also tried to create my own solar panel, but can't figure out how to save it as "my own" family.
I simply want to tilt the panel back about 35 degrees. I've tried to tilt it in all different views. Sometimes I can get it to tilt along the wrong axis, never on the one I want it to. Is there any way I can create my own panel with a sketch program, import it into Revit, and save it as a component?
Is it possible to put Reveals in concrete columns?
View 3 Replies View RelatedI've had a request from on of our users to replicate something that has been done for years in 2D CAD. They want a marker to show changes in floor levels that look something like this:-
The annotation needs to be able to read the slab on either side of the step marker and hopefully if possible the difference be represented as text. The datum levels are secondary and it is really the depth of the step that seems to be more important. I do however want to avoid these being just dumb text as if/when the design evolves someone will forget to modify the text.
Here is an example of a few showing two steps in the slab and the results we would want.
I have tried loading/nesting a standard spot level in thinking if I had two in an annotation that this might work, but I was unable to even place a spot marker within the family which makes some sense I suppose.
Is this even technically possible...? I realize the origin usually determines what hosts the family and how, but I guess we are looking for something with a double origin, which is why I think this may not be possible...?
Is there any way to replicate this skin of solid glass spheres hardened into concrete in the form of a panel of some sort?
View 9 Replies View RelatedHow do I insert, or what Family do I insert Concrete Unit Masonry? I have CMU piers for my foundation.
View 2 Replies View RelatedI have created my model, and have placed the floor assembly in. It is concrete and I see the concrete pattern on the floor. How do I hide or turn that off? I cannot find anything in Visibility Graphics or in the actual floor family...
View 6 Replies View RelatedWhat's the best way to model a concrete beam that has the fireproofing in it?
View 4 Replies View RelatedHow can i draw column like this >>
View 1 Replies View RelatedHow to use a 6" concrete curb under exterior walls for California schools? are you using a stacked wall, and if so how do you get the exterior finish to cover up the concrete curb. Or if you are using basic walls stacked upon one another, I seem to have trouble getting my wall joins to look correct in plan.
View 3 Replies View RelatedIs there a quick way of profiling topography under a undulating concrete floor slab? In other words so that the topography follows the underside surface of the slab. I know this is possible by adjusting each point on the topo surface but is there a quicker way?
View 1 Replies View RelatedIn floor plan view how do I make a wall have a concrete texture inside instead of the default (criss cross)?
View 9 Replies View RelatedI use all the time L shape and U shape winder stairs in combination with the Monolithic Type.
We use to concrete the monolithic part of the stairs and then dress the stairs with treads and risers. The new tool looks that working very nice.
So OK I draw the U shape winder stair and of course i want to construct the stairs.
I want to prepape a detail plan view with dimensions only for the Monolithic Part (Concrete) of the stair but i can't find a way to dispay only the monolithic part without Treads and Riser.It is possible in 3d view but no in plan view. The news tool that calculate winder stairs is "half job done" if i can't print with dimension the concrete part of the winder stairs.
I'm trying to build a wall that has the concrete block pattern that's offset by 1/2. If I build a wall using mass then I can make it into a pattern that I want but then I can't paint it so that's it's clear or see through. On the other hand if I build a wall just using the walls then I can't find an option for the block pattern.
View 1 Replies View RelatedI've created an irregularly shaped mass (column corbel) within a project and would like to make it a concrete object. How do I do this?
View 1 Replies View RelatedI am trying to use the "tilt" tool in the (create a new brush) panel and it is not being highlighted as an option to click on.
View 1 Replies View RelatedI wonder how do you create a concrete construction under the stairs?
The way ACA creates stairs looks like just a top layer (tiles or wood panels), but I want to put those tiles on a concrete construction.
if this is easy, but how do I calculate the volume of concrete needed to pour a cast-in-place spiral stair?
View 1 Replies View RelatedI am trying to create tilt shift effects. issue in selecting focus and blur areas. I do the following - Go to Quick Mask(Press 'Q') --> Select Gradient (Press 'G') --> Then I draw a vertical line to define the focus area. Usually a relatively darker red color used to appear as a band. But suddenly I see a very vague red color. And when I exit Quick Mask (Press 'Q') again the marching ants selects the entire picture and not the focus and blur areas.
View 1 Replies View RelatedI've been added and removed specific mullions along curtain wall grid lines and now have the mullions where I want them. Unfortunately, some of the glass panels remain divided along the grid lines even though the mullions have been removed. Is there some way to join the two panels into one?
View 9 Replies View RelatedI created a curtain panel family and loaded it into my project where I had created a mass and divided the surface, and changed the panels to be my curtain panel family i created. The mass has a curve that I want the panel to be on the inside of, but the panel is always placed on the outside. File is attached. So on the smaller curve on the north side of my building, the panels are placed on the inside of the building instead of the outside. How can I place the panels on the outside of the building along the curve?
View 3 Replies View RelatedI'm missing some buttons from the panels in Revit LT 2014. I've installed updates 1 and 2.
View 6 Replies View RelatedI am trying to export my floor plan to dwg file and I have curtain wall there which have panels as regular wall types. The problem is that exporting it will put those panels on the wall layer. I need them to be on curtain wall panel layer. I tried to use "Function" parameter in wall family by changing certain wall types to Retaining (since I don't use this parameter) and changed Wall/Retaining category layer to curtain panel in dwg export setup. But it seems it has no effect.I also noticed that walls inserted as panels into curtain wall do have a parameter under "Identity Data" with the name "Categorize as" where are two values - wall or panel. But this does not have any effect either since there is no category for it in export setup.
View 2 Replies View RelatedI have created a operable window to insert in a curtain wall system based on the "Window - Curtain Wall" family. I created a simple extrusion for the glazing panel and assigned it the subcategory of "Glass". When loaded in the project, the cut lines of this panel are a much heavier weight than mullions, other glass panels, etc. The lines are so thick, the double line just becomes a fat single line as they merge together. Adjacent glass panels don't have this line weight problem. I can find no override or other control/parameter that fixes this.
View 1 Replies View RelatedI created a curved, sloped wall (it's actually a tower) using in place mass, model by face - wall. I need to place reveals in the wall to simulate ACM panels. I've tried using the reveal tool in the wall drop down but it won't allow a reveal to be placed in the custom wall.
View 4 Replies View RelatedI am running Windows 8. I have used multiple .NET Framework removal/repair tools, tried uninstalling all versions of .NET and reinstalling 4.0 from its official Microsoft standalone installer. However, every time I try to install 4.0, I recieve a message stating that it or a higher version of .NET is already installed.
Upon further research, I was informed that the .NET 4.5 Framework is an integral part of Windows 8 that cannot be uninstalled.
I cannot access any of the tools I need to in the program, so it is basically rendered useless (don't tell me to just use shortcuts because that is extreemely tedious and painful to make work properly, ive tried it). I have also thought about just installing Revit 11' and using that, but it is no longer available from Autodesk!
I am trying to align the curtain wall with the edge of the concrete slab/face of wood framed wall (Core). I have tried to align and move however the whole wall moves as well as the edge of the slab. How I can move the Curtain wall leaving the other elements in place?
View 2 Replies View Related
