Is there a shortcut to draw a 45 or 90 degree angle from a drawn line on an angle using the pen tool? ie. Rather than just from the x and y axis.
I trace a lot of maps and site plans.
How to draw a line with given angle at the end? What is the command?
View 4 Replies View RelatedLet's say I am inserting a square block into a dwg and want to get it parallel to an existing angled line. Do I have to read the angle of the line and insert the block to that angle or is there a quicker way?
View 6 Replies View RelatedHow to draw a line that STARTS at a perpendicular angle to another line ???
View 4 Replies View RelatedHow do i draw line at specific angle. if i have the length on the x axis and angle, when i do @.25<45 the line becomes .25 in length i need the x dim to be .25 @ 45 degrees. as shown in the picture
View 9 Replies View RelatedI don’t know if there is some way to draw, or somehow to say to AutoCad that it let me to input measurements from line but not from main base pint.
For example in Revit I can make angular dimension between lines and then apply any angle that I want, maybe AutoCad has such tool?
Is it possible to draw an angle (eg 50x50) using the multi line command with the internal & external corners of the multi line angle radius?
View 5 Replies View RelatedHow do you draw a line without the line length/angle showing as to go?
View 6 Replies View RelatedWhat is the most efficient way to draw a line inclined by particular angle from another line?
I wanted to draw a line inclined by particular angle from another line but couldn’t get the best way to do that.
For example, in the screenshot below, I wanted to draw a line inclined by 60º from an existing line but couldn’t approach the best way to approach it.
How can I draw this line efficiently?
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
good way to start a line at one of the 45 degree angles of a circle block?
View 9 Replies View RelatedWhen drawing rectangles a symbol ( verticle line with arrow pointing to left ) is below and to the right of the cursor, The rectangles are drawn at an angle. How do I draw them horizintally?
View 3 Replies View RelatedI'm trying to sweep it around shape like this But it won't, it says "The selected path curve is not valid." - so what do I do? (it is polyline) Is there maybe some other way to get this 3D shape fast?
View 8 Replies View Relatedeasier way to program 45 degree corners on the top flange of two mating parts. We can't bend the ends on so they have to be welded. I am using inventor 2014 professional. Almost all my programming is done in sheet metal.
View 2 Replies View RelatedI'm experimenting with 3d printing and wish to create a tube system based on this vase. Im completely new with 3ds max. What's the easiest way to simply bend the entire model 90 degrees? URL...
View 2 Replies View RelatedI'm trying to draw the following bench in Autocad but I'm getting bogged down trying to figure out how to create the following tube with an angle on it and how to achieve different shapes at the top of tube.
View 9 Replies View Relateduntitled.jpg
Is there a way to convert those lines into plines, so i could extrude and cut.
wrapping a continuous line of text around a 90 degree bend. The third attached image is exactly what I need it to do. That is something I just put together as an example though.
I have some repeating information that I want to wrap around the border of an image. Being that it is repeating information, the text can also look like the first and second image uploaded, where part of the word is cut off. I would prefer this to be minimal though.
So far all I have found in my time searching on this leaves the words distorted.
No matter the complications, this also needs to be scripted. It is not feasible to do this manually as the repeating information is dynamic.
EDIT: The upload for the thumbnails is off.
Added Details.Attached File(s) textwrap2.jpg (8.9K)
Number of downloads: 19 textwrap2.jpg (8.9K)
Number of downloads: 17 textwrap.jpg (8.38K)
Number of downloads: 7
I am trying to make a toilet paper roller; standard white ones with the spring inside [URL] .
I need to cut the bottom of the cylinder at a 45 degree angle from the center to wall so if the roller was standing, it would be at an angle of 45 degrees to.
I have attatched what I have so far.
I am having trouble with the slicing. I am not sure how to chop the whole cylnder at an angle.
Also how do I remove the yellow lines and the white line with the measurement .1280 (you'll understand when you open the file)
I am trying to make a cut on a 12" D cylinder at a 45 degree angle and i am having a little trouble. I have projected the shape onto the curve and sketched it. Now to finish the cut do i need to scuplt that path or how do I go about doing this.
I provided a screen print to try and and explain it a little batter. The half moon looking sketch is what i am tring to cut out of the cylinder. i have already projected the surface lines on the cylinder, but get stuck at this point
I am have a problem. How do you create a cylinder with a flat end on one side and on the other side have it at a 45 degree angle.
View 4 Replies View RelatedI'd like to orient a picture of a book so that it's on a 45 degree angle and then "cut out" the area around the "book" to that when you view the picture is looks like a book on a 45 degree angle with no area around it. I'm sure GIMP can do that but the question is whether I can put that same photo on a website and have it look like it's a book on a45 degree angle.
View 4 Replies View RelatedWhat's the best way to model an alley with a 90 degree angle (turn). Do I treat it as an intersection with a zero radius? My typ section is 15 feet width with a 4% slope down to the center of pavement. "V" bottom. Not sure how to get it to model the outside corner and also eliminate the inside overlay.
View 8 Replies View RelatedI'm trying to create a dynamic block for plywood. I have the stretch parameter working so that I can stretch the plywood to the needed length. I also have set a rotation parameter based on the various roof pitches that we use. The problem is I would like to be able to rotate the sheathing to a 45 degree angle and then stretch along the 45 degree angle. Once I rotate the sheathing the stretch does not follow the rotation angle. I have attached the file.
View 9 Replies View RelatedHow to get the correct notation for the angle in degree/minute/second?
I wanted to show the angle as 29˚12’13’’ but not as 29d12’13’’
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
how do one wants to do a polar increment angle to make a degree in a autocad drawing. I want to design a truss but at the angle of the truss , how to make an angle between the top chord and lower chord. which icon i should click on ?
View 3 Replies View RelatedI'm trying to figure our how to taper a circular object 1-1/2" high on a 45 degree angle from the top down (that is the lower part goes in like a pie pan). Taper doesn't seem to work.
View 2 Replies View RelatedIm drawing in isometric view and want to change the default drawing angle from 30 degrees to another angle.
View 9 Replies View RelatedIs there a quick way to rotate an object to match an angle without knowing what the angle is? I am using AutoCAD 2011 now. I was using 2007 and I had an add on command the would rotate an object using a base point and picking the two lines that make up the angle, and it would match the angle you wanted. I can not get that command to load in 2011.
View 4 Replies View RelatedI have a property line that is N 36d19'52" E but needs to be N 12d52'18" E. The obvious and calculated rotation angle would be 23d27'34" but when I rotate the line by the calculated angle it doesn't rotate to the right angle. It's off by 0d11'10"!? When I draw a line by bearing at N12d52'18" E and inquiry the angle between the property line and the drawn line the angle difference is in fact 23d27'34".
View 1 Replies View RelatedI have used a driven contraint in a sketch.
Can that also be done in an assembly?
In one assembly I want to make one angle half of a driven angle.
how to convert "real world" angles of elliptical arcs into those shown in a dxf file?
Say that I have drawn an elliptical arc with its start angle on 210 degrees and an end angle of 324 degrees. The values in a DXF file, for an elliptical arc, have something to do with the contant "PI" (3.14159). I know that a full circle is 2*Pi but how to do this with elliptical arcs!!
