AutoCAD 2010 :: Draw A Line Without Length / Angle Showing As To Go?
Feb 15, 2012How do you draw a line without the line length/angle showing as to go?
View 6 Replies
ADVERTISEMENT
AutoCAD 2010 :: Most Efficient Way To Draw A Line Inclined By Particular Angle?
Apr 17, 2012What is the most efficient way to draw a line inclined by particular angle from another line?
I wanted to draw a line inclined by particular angle from another line but couldn’t get the best way to do that.
For example, in the screenshot below, I wanted to draw a line inclined by 60º from an existing line but couldn’t approach the best way to approach it.
How can I draw this line efficiently?
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
AutoCad :: How To Make Third Line Relative To Second Line So Angle Is 75 Degrees And A Certain Length
Oct 27, 2009I have been practicing using a older book(copyright 1990) and it has some decent exercises in it. I was able to do this one but it seems I can"t find the proper way to do this..First drawing a line a certain distance..ortho on,click the first point anywhere,move curser to the left and click again. that gives me a line at 180 degrees at what ever length..Line command again starting at the second point of the first line..after clicking that point,I type in @2.38<150 that gives me a line2.38 long at 150 degrees..now how do i make a third line relative to the second line so that the angle is 75 degrees and a certain length..the picture shows what I am trying to draw..using the polar cordinates you get an angle based off the UCS( which is set at world) when you try to draw the third line ..that makes the angle between line 2 an 3 not the angle that I want..To make the drawing,I rotated the ucs -30 degrees..But there has to be a better way than that..
View 9 Replies View RelatedIllustrator :: Shortcut To Draw A 45 Or 90 Degree Angle From Drawn Line On Angle?
Nov 13, 2013Is there a shortcut to draw a 45 or 90 degree angle from a drawn line on an angle using the pen tool? ie. Rather than just from the x and y axis.
I trace a lot of maps and site plans.
AutoCad 2D :: Draw A Line That STARTS At Perpendicular Angle To Another Line
Jun 27, 2012How to draw a line that STARTS at a perpendicular angle to another line ???
View 4 Replies View RelatedAutoCAD Architecture :: How To Draw Line In Particular Angle From Another Line
Apr 13, 2013I don’t know if there is some way to draw, or somehow to say to AutoCad that it let me to input measurements from line but not from main base pint.
For example in Revit I can make angular dimension between lines and then apply any angle that I want, maybe AutoCad has such tool?
AutoCad :: Angle To Put A Line Of Specific Length Between Parallel Lines
Jun 23, 2012I am drawing a diagram to describe a mathematical word problem. Since it is easier to visualize with a drawing, I want to draw it using the given dimensions. But angles used in the diagram are unknown and are not needed for the answer to be calculated, so the only way to draw this freehand is to guess at the angle resulting in the correct distances to be off.
Here is the word problem: There are two ladders, one 40 feet and the other 30 feet, each touching the base of one of two buildings and leaning against the other building. If the ladders cross 10 feet above the ground, how far apart are the buildings?
So for my drawing, being rather simple considering what AutoCAD can do, results in this:
Can AutoCAD calculate the angle needed to place a line of a given length between two parallel lines that are a distance apart less than the length of the line to place between them, having the endpoints of this line touching the parallel lines, fitting exactly?
For the word problem, the distance between the two parallel lines is what needs to be solved and the math is quite invloved, having to find the roots or solution of a quartic equation. (I have the solution figured out to be 26.03287754 feet)
What I am afraid of is that this would require to program an AutoLISP routine to create a new command that one can call from the command line. I see it using the the measure command with relative and absolute co-ordinates. This may be far from a "beginner" question. I can do this quite easily on a peice of paper: having two parallel lines drawn, take a ruler and placing the "0" mark on one line, then adjusting the angle until the desired length just reaches the opposite parallel line. I used to use this trick quite often when drafting with pencil and paper to divide a distance into a required number of even amounts, so this can't be that difficult to do with AutoCAD!
AutoCad :: Draw Line With Given Angle At The End?
May 3, 2012How to draw a line with given angle at the end? What is the command?
View 4 Replies View RelatedAutoCad 2D :: How To Draw Line At Specific Angle
Oct 12, 2008How do i draw line at specific angle. if i have the length on the x axis and angle, when i do @.25<45 the line becomes .25 in length i need the x dim to be .25 @ 45 degrees. as shown in the picture
View 9 Replies View RelatedAutoCAD 2010 :: Lips For Show Length And Angle Cannot Use In 2012?
Sep 25, 2013before this i use in autocad 2007 and dont have a problem but in autocad 2012 have bug and only showing angle only
View 9 Replies View RelatedAutoCad :: Draw Angle Using Multi-line Command
Nov 6, 2013Is it possible to draw an angle (eg 50x50) using the multi line command with the internal & external corners of the multi line angle radius?
View 5 Replies View RelatedAutoCad :: How To Draw Line To Exact Coordinate And Length
Feb 2, 2012I would like to draw a line that is a specific length, lets say 16, that originates from a specific x,y location say 10,23, that terminates at exactly atleast the y coordinate 38. I don't care about the x or the angle.
View 9 Replies View RelatedAutoCad 2D :: Draw Line Snapped To 45 Degrees Angle Of Circle Block
Aug 15, 2011good way to start a line at one of the 45 degree angles of a circle block?
View 9 Replies View RelatedAutoCad 2D :: Draw Line Exact Length When Dimension It With Fraction Rounds Up
Dec 11, 2012it's been awhile since I have been back to autocad. I draw a line an exact length then when I try to dimension it with a fraction it rounds up. I can't find the setting. It is say 5 1/2" but will dimension to 6"..
View 7 Replies View RelatedAutoCAD 2010 :: Line Length Display Box Missing?
Oct 19, 2010I must have changed a setting and now I cannot figure out what I did.
On AutoCad at school, when drawing a line, there is a light blue dialogue box that would pop up above the cursor telling you the length of the line before you set it. (not the coordinates).
This is not showing up on the educational version of AutoCad I am running at home.
CorelDRAW Graphics Suite X5 :: Draw Needle And Thread Showing Curved Line?
Jun 22, 2011I am trying to draw a needle and thread showing a curved line as the thread with parallel lines so I can show where the thread crosses over itself. This is used as a stitching diagram.
View 3 Replies View RelatedAutoCAD 2010 :: How To Draw A Line With Fixed Ends
Dec 27, 2012Is it possible to draw a line with fixed ends. I want to draw a line, representing a pipe, which connects two tanks. Whenever I move one of the tanks I'd like the line automatically to adjust its coresponding end in such a way that the line aways will start from the one tank and end on the other. Is it possible that?
Another question, is there some option, such that whenever two line cross each other, one of the line automatically to go over the other. By this I want to show on the drawing that the two lines are not connected. Something like the following "sketch"
AutoCAD 2010 :: How To Draw A Line Perpendicular On Arc At Particular Point
Apr 21, 2012How to draw a line perpendicular on an arc at the a particular point?
I wanted to draw a line perpendicular to an arc at a particular point but couldn’t approach it. In this case, I need two snaps to work at the same time! To be perpendicular on the curve and at the same time to be snapped to the point!
AutoCAD 2010 :: MText Area - Adjust Single Line Text So That End Of Sentences Make Angle
Apr 5, 2013I use Mtext quite a bit and I am trying to convince others in the office that it's a good thing (versus single line text in long paragraphs). One of their concerns in the shape of the Mtext. For instance, when you use Mtext, you type into a nice rectangle that you can change the size of. What they have to do on occassion is instead of having a nice rectangle of text, they have to make it like a triangle. So in this case, single line text can be adjusted so that the end of the sentences make an angle.
Is there a way to do this using mtext? Or is there an lsp that will work?
AutoCAD 2010 :: Draw A Line Inside Cell In Table
Mar 6, 2012how can i draw a line/arc inside a cell in ACADTable.
View 2 Replies View RelatedAutoCAD 2010 :: Excel Data Coordinates To Draw Line?
Feb 20, 2013I want to drawn LINE by excel data to autocad 2010, I have excel file x,y and z coordiates.
I want to draw line to import excel data coordiates to autocad ?
AutoCAD 2010 :: Draw Line Segment On The Surface Of 3D Object?
May 3, 2012I made a 3D box shape in AutoCAD. I would like to draw a line on one of the surfaces of the box. Also I know you can use the the linear tool under Annotations to display dimensions of 2D lines. But I don't know how to do it so that it that shows the dimension on a vertical axis as shown in the picture below.
View 9 Replies View RelatedAutoCAD Dynamic Blocks :: Change Length Of Line Based On Length Of Attribute
Jan 8, 2013Is it possible to change the length of a line based on the length of an attribute?
I'd like to make the line a MINIMUM length of X" (I haven't decided how long yet--but know I'll need a minimum). But then after the user fills in the attribute, I'd like the length of the line to change to the length of the attribute plus a small amount (again, I haven't decided yet how much extra).
AutoCAD Dynamic Blocks :: Line Length Follow Content Length Of Attribute
Mar 16, 2012I was wondering if there is a way with DB's to have a line "follow" or "grow" with the content/value length of an attribute. Maybe some method of linking the attribute width to length of the line? Essentially, it would work just like turning on the underline setting when typing in mtext editor (or any program with an underline option for that matter), expect that the line could be placed anywhere, and would not have to reside directly below the text.
View 5 Replies View RelatedAutoCad :: How To Read Angle Of Line And Insert Block To That Angle
Feb 11, 2011Let's say I am inserting a square block into a dwg and want to get it parallel to an existing angled line. Do I have to read the angle of the line and insert the block to that angle or is there a quicker way?
View 6 Replies View RelatedAutoCAD 2010 :: Line / Object Selection Not Showing On Properties Tab?
Jul 6, 2012We have this problem with nothing showing up in the properties tab when we select a line/object.
We have tried everything from here:
[URL]
But still can't get it work.
Is this more of a Windows issue rather than AutoCAD? We are running Windows 7/64.
AutoCAD 2010 :: Line Type Is Not Showing Up Properly In Viewport?
Jul 7, 2011For some reason my line type is not showing up properly in my viewport. In model space my lines are dotted, but when I go to viewport they show up continuous??
View 6 Replies View RelatedAutoCAD 2010 :: Line Type Not Showing Up Properly In Paper Space
Jan 27, 2011My "center" line shows up fine in model space, but just solid lines in paper space.
View 7 Replies View RelatedAutoCad :: Extracting Length / Angle
Apr 7, 2011I have the base point X and the secondary points from lets say 1 to 20 (total of 21 points)
I draw lines from X to every one of the secondary point (from point X to point 1; from point X to point 2; from point X to point 3; ........from point X to point 20)
If you click proprieties on one of the lines, you will see that it has a Length and an Angle. I need to manually copy the length and the angle of every line, and paste it in a table on Excel/Word.
Problem: I have about 100 points a day of this kind, so manually copying their length & angle is a real pain. Is there any way faster to do this. A specific command in AutoCad (2006).
AutoCAD Inventor :: Angle Of Plane By Length Of 3D Sketch?
Aug 26, 2013I am jammed in this matter...I have my 3d sketch and i would like to control the angle betewwen the two planes with
the dimension of the 3d sketch. I am at the level that i can change angle between planes.
AutoCAD Civil 3D :: Labeling - Arc Using The Angle Rather Than Length Or Radius
Sep 4, 2012Just started a drawing in C3D 2013 using an existing template. If I draw an arc using the "Angle" rather than length or radius, entering the angle as 11.1601, then label the arc, the delta angle is converted to hms or 11.0936 . The template and labeling style are ones we've used for several releases. I've compared the feature settings, units and the curve labeling command and can not find where this is being changed.
View 8 Replies View Related
