AutoCad :: Draw Angle Using Multi-line Command
Nov 6, 2013Is it possible to draw an angle (eg 50x50) using the multi line command with the internal & external corners of the multi line angle radius?
View 5 Replies
ADVERTISEMENT
Illustrator :: Shortcut To Draw A 45 Or 90 Degree Angle From Drawn Line On Angle?
Nov 13, 2013Is there a shortcut to draw a 45 or 90 degree angle from a drawn line on an angle using the pen tool? ie. Rather than just from the x and y axis.
I trace a lot of maps and site plans.
AutoCad 2D :: Draw A Line That STARTS At Perpendicular Angle To Another Line
Jun 27, 2012How to draw a line that STARTS at a perpendicular angle to another line ???
View 4 Replies View RelatedAutoCAD Architecture :: How To Draw Line In Particular Angle From Another Line
Apr 13, 2013I don’t know if there is some way to draw, or somehow to say to AutoCad that it let me to input measurements from line but not from main base pint.
For example in Revit I can make angular dimension between lines and then apply any angle that I want, maybe AutoCad has such tool?
AutoCad :: Draw Line With Given Angle At The End?
May 3, 2012How to draw a line with given angle at the end? What is the command?
View 4 Replies View RelatedAutoCad 2D :: How To Draw Line At Specific Angle
Oct 12, 2008How do i draw line at specific angle. if i have the length on the x axis and angle, when i do @.25<45 the line becomes .25 in length i need the x dim to be .25 @ 45 degrees. as shown in the picture
View 9 Replies View RelatedAutoCAD 2010 :: Draw A Line Without Length / Angle Showing As To Go?
Feb 15, 2012How do you draw a line without the line length/angle showing as to go?
View 6 Replies View RelatedAutoCAD 2010 :: Most Efficient Way To Draw A Line Inclined By Particular Angle?
Apr 17, 2012What is the most efficient way to draw a line inclined by particular angle from another line?
I wanted to draw a line inclined by particular angle from another line but couldn’t get the best way to do that.
For example, in the screenshot below, I wanted to draw a line inclined by 60º from an existing line but couldn’t approach the best way to approach it.
How can I draw this line efficiently?
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
AutoCad 2D :: Draw Line Snapped To 45 Degrees Angle Of Circle Block
Aug 15, 2011good way to start a line at one of the 45 degree angles of a circle block?
View 9 Replies View RelatedAutoCad :: How To Read Angle Of Line And Insert Block To That Angle
Feb 11, 2011Let's say I am inserting a square block into a dwg and want to get it parallel to an existing angled line. Do I have to read the angle of the line and insert the block to that angle or is there a quicker way?
View 6 Replies View RelatedAutoCAD 2010 :: Can't Convert Multi Line Attributes To Single Line
Jan 22, 2010We are creating a new company title block for the use in Inventor 2010 and AutoCAd 2010. It has initially been generated in Inventor and exported to AutoCAD. My problem is that all attributes that came over are now setup as multiline attributes and I can't seem to change them to single line. Therefore you have to open the multiline editor separately for every single item to make changes in lieu of just 'tabbing' through the values in the Enhanced Attribute Editor. This adds time and frustration and seems to be intolerable for some of my colleagues.
Is there a way to change the attributes to a single line in AutoCAD I'm just not aware of? I tried to find different settings for the export from Inventor but the options seem to be very limited.
I could probably go over this and create separate AutoCad only titleblock and border but that would kind of defeat the purpose.
AutoCad 2D :: Convert Single Line Text To Multi-line
Mar 20, 2008We have an employee in our office that is kind of old school in some ways. That person has a habit of exploding everything possible in a drawing. Most of us create notations using mtext so it's easy to edit and manipulate. Is there a way to convert the single line text back to multiline after it's exploded?
View 9 Replies View RelatedAutoCad :: How To Draw Section Plane At Angle
Jun 15, 2011I have a cube and I want to create a section plane that goes trough the middle of 3 edges that have a common point. After this I should be able to erase the smaller solid and keep the bigger one. If needed I will attach an image to be better understood.
View 4 Replies View RelatedAutoCad :: How To Make Third Line Relative To Second Line So Angle Is 75 Degrees And A Certain Length
Oct 27, 2009I have been practicing using a older book(copyright 1990) and it has some decent exercises in it. I was able to do this one but it seems I can"t find the proper way to do this..First drawing a line a certain distance..ortho on,click the first point anywhere,move curser to the left and click again. that gives me a line at 180 degrees at what ever length..Line command again starting at the second point of the first line..after clicking that point,I type in @2.38<150 that gives me a line2.38 long at 150 degrees..now how do i make a third line relative to the second line so that the angle is 75 degrees and a certain length..the picture shows what I am trying to draw..using the polar cordinates you get an angle based off the UCS( which is set at world) when you try to draw the third line ..that makes the angle between line 2 an 3 not the angle that I want..To make the drawing,I rotated the ucs -30 degrees..But there has to be a better way than that..
View 9 Replies View RelatedAutoCad :: Drawing Bottom Line With Angle Of 132 Relative To Middle Line
May 15, 2013angle.jpg
How can I draw the bottom line, with an angle of 132 relative to the middle line?
AutoCad 3D :: Setup Drawing Direction - How To Draw From Angle
Oct 6, 2012I would like to draw from the side, especially circles to extrude. see my pic below. my current view only allows to pull circles up etc. I don't want to rotate all the time.
how to you set this looking angle up?
drawing direction.fw.png
AutoCad :: Drawing A Line At Angle With Another Line As X Axis?
Oct 22, 2011I have to draw a rather weird drawing with a lot of angled lines. Currently I'm using UCS to draw them but it's really tiresome.
I would draw 1 line, then type in UCS, select the X and Y axis, draw that line, escape, then hit in UCS again, rinse and repeat.
Is there a simpler way? I tried polar tracking "relative to last segment" but it still uses the x axis as the base, which is not what I want. I want the line to be the X axis.
AutoCAD Civil 3D :: Draw Corridor Corners With 90 Angle No Curve
Sep 17, 2013I am trying to figure out how to draw a 90 angle bend with no curves. With smooth outer line.
View 3 Replies View RelatedAutoCAD Inventor :: Draw Rectangular Patterned Array Of Objects At An Angle?
Apr 24, 2013is there a way to create an associative array of posts so I only have to edit one part to have the entire array change? that is, I want to have global values for the dimensions in the picture below: post diametervertical width between post centreshorizontal width between post columns (again, centre to centre)vertical shift of each column w.r.t. previous one I've used the Rectangular Pattern tool to create a repetition of my posts, but I want to shift each column of posts up slightly with respect to the one before as in the attached picture:
It seems that if you want to repeat along non-perpendicular axes like this, Inventor fails if there are too many repeats. I came across this when searching the site:
[URL]
I can verify that this is my exact problem but can add that in my example, 4 repeats on the almost horizontal axis and 3 on the vertical work fine. However, 3 almost horizontal axis repeats by 4 vertical axis repeats will only work if I choose the vertical axis as Direction 2. (Is this a bug or am I trying to use the Rectangular Pattern Tool incorrectly?)
The repeat unit can be simplified to 1 circle with 2 construction lines along the repeat Direction instead of the 2x2 circles shown here but the problem persists. Also
AutoCad :: Draw Isometric Version Of Part From First Angle Orthographic Projections
Oct 31, 2012I am trying to draw an isometric version of this part from first angle orthographic projections. But for the life of me I can't, I have never been good at nets / pr Attachment ortho to iso.jpgojections etc.
View 9 Replies View RelatedAutoCad 3D :: Command To Extrude At An Angle
Nov 28, 2011Is there a command to extrude something at like a an angle. Im not talking about taper but something that could extrude at an angle.
View 9 Replies View RelatedAutoCAD Inventor :: Cursor Change To Draw Line But Line Doesn't Appear
Dec 5, 2011I have a problem with a recently downloaded version of Inventor. When I start a new drawing all I get is a blank blue screen instead of one with a grid display. If I start a line I can see the cursor change to draw the line but a line does not appear. I don't know if it something with how I installed the program or just system settings.
View 2 Replies View RelatedAutoCad 3D :: Angle Command To Chamfer Tool In 3D
May 20, 2011Success using AutoCAD's CHAMFER>ANGLE command to chamfer in 3D? Distance/Distance works fine, but I haven't yet figured out how to use the chamfer tool to put a 30 degree chamfer on a cylinder (or any angle for that matter) by specifying a distance and an angle. Seems like it should be simple, but I always give up and end up creating the tapered edge by revolving a polyline that already has the chamfer, or using the TAPER>FACES tool.
View 9 Replies View RelatedAutoCad 2D :: Change Default Value Of Angle That Is Between <> In Command UCS
Oct 2, 2013How do I change the default value of the angle that is between <> in the command UCS
"specify rotation angle about X axis <180.00>:"
from 180.00 to 90.00
AutoCad :: How To Draw Cross Section Of Timber Winder Stairs As Strings Change Angle
Jun 1, 2012Just learning 2D CAD and trying to draw a cross section of a timber winder stairs as the strings change angle (I think) at the winder section. Looking at 3nr winding steps.
Setting out a standard stairs is okay, so I have the floor to floor height.
AutoCad :: Draw Straight Line Without Protractor Shaped Dotted Line / Unable To Set User Interface
Jan 22, 2012How can I draw a straight line without that protractor shaped dotted line following my cursor making it lag and also not snap correctly to the next line? Also, I have noticed that I can't set my user interface to auto cad classic settings. There seems to be no option for it in workspace settings.
View 3 Replies View RelatedAutoCad :: How To Use Offset Commend To Draw A Parallel Line To Another Line
Sep 14, 2011in autocad we use offset commend to draw a parallel line to another line what we should we use in Chief Architect x2
View 1 Replies View RelatedAutoCAD 2013 :: Command Line Appears Again After Plot Command?
May 15, 2012I press CTRL+9 to make the Command Line disappear while drawing. When I plot (or when doing a plot preview) , the Command Line appears again by itself. So I always have to turn the Command Line off manually after each plot
The bug still happens;
- if Dynamic Input is turned off or on
- if I plot to a real device or in PDF
- if the Cammand Line Palette i docked or floating.
This is not an issue in AutoCAD 2012 so I guess it has to do with the new way they programmed the revamped Command Line palette in 2013.
Using Windows7
AutoCAD 2013 :: Draw A Line From End Of Line To Start
Jul 31, 2013I was drawing a lot of lines with the pointer that stuck at the end of the line and after that it stuck at the beginning of the other line (i hope you understand what i mean). I don't know what i pressed but now this function is not active and is very difficult to draw the lines.
View 3 Replies View RelatedAutoCad :: Draw Layout For Simple Angle Iron Part Using Front / Side And Angled View
Apr 25, 2011Im currently trying to draw a layout for a simple angle iron part using the front, side, and angled view. Its a flat part made of sheetmetal and it will get 1 90* bend in it.
My first question is how do i bend a part in autocad LT 2011? Ive been using autocad for years but ive never had a request for an angled view.
My second question is how would i create a layout using all 3 views and include the info block in the bottom right displaying all the info?
AutoCAD 2010 :: Make Line Boundary Around Multi-line Text Region Corresponding To Text Mask?
Apr 27, 2010I need to do it quickly with many text regions. How to make line boundary around multi-line text region corresponding to text mask?
View 9 Replies View Related