i want to snap this line to where it would be at a tangent to the arc (as right), but as you see (left) when i hover with TAN snap it picks a tangent from the pick point, not from object's orientation.
at the moment i construct a tangent by rotating a copy of my line by 90°, and snapping it to centre of the arc. then extend out past arc, where the intersection is now the point i originally wanted to pick. make sense? gotta be a better way!
Since switching over to Inventor 2012 I have been having trouble snapping to tangent points on a curve or circle to pull dimensions. I would do it manually but if the dimension is not referencing a specific point in the model it turns pink to identify an error.
Is there a setting that may be not allowing me to snap to tangent points?
how to get AutoCad 2004 to snap to an IsoCircle tangent correctly without having to do it twice? Hope I've explained that correctly. If I try to join two IsoCircles with a line AutoCad doesn't pick the correct tangent straight away, but if you carry on and create the line anyway, then delete it and create it again it works.
Working on Acad2012 3d Civil. I draw a circle of 4000' radius and another one of 2000' radius. I put a tangent line between the two circles and I do see the tangent symbol but when I zoom in real close, it's not. So now I can't trim the excess radius of the two circle. I do have a trim line pasted the two supposedly tangent points. Is this a CAD issue or is their a variable to change that actually makes the lines tangent.
I’ve an already drawn inclined line from a fixed point (saypoint (0,2) on Y-axis). The inclination is also fixed (say 150 tothe horizontal). My objective is to draw a circle with one quadrant at a fixedpoint (say point (1,0) on X-axis), so that, the line becomes a perfect tangentto the circle. The diameter of the circle may vary to make the line perfecttangent to the circle.
I am attempting to keep the cable line of the crane always tangent to the circle at the top of the crane. The length of the crane (including the circle at the top) is being polar stretched but i am unable to keep the cable tangent to the top circle as i stretch and rotate the crane.
When inserting a DIMRADIUS in older versions of AutoCAD, the extent of the radius dim used to automatically stop at the tangent point along an arc. However, now in ACAD 2013 (and possibly other recent versions), a red 'extension' line is carried on beyond the tangent point, which I don't want. Is there a toggle that switches this off so that the radius dim stops wholly at the tangent point as before?
I've tried using endpoint snap to stop the dim at the tangent point, but the radius dimesion text is then placed on the outside of the curve rather than the inside where I want it.
I am trying to create a dimension in an .idw that goes from a line to the tangent of the outer diameter. I have tried several approaches but I cannot get it to work. Essentially I am trying to replicate a drawing which was created in Solidworks but I am having trouble with this dimension.
How to correct length line Tangent Edges, Foreshortened (sheet metal drawing) ? I didn't find option to correct length line Foreshortened (sheet metal drawing) .
We have a need to select a tangent line/polyline etc and then select two other points we would then like to have the program draw an arc through the two points and yet still be tangent to the initial line/polyline that we picked. We don't care what the radius is as we believe there is only one solution anyway. It would be wonderful if we could just use the Arc command and select start>Second Point> then just use the Tangent Osnap but I guess that is out of the question :-)
The only code that I have come across that even resembles this only allows for one point not two (STILL VERY HANDY AND VERY SLICK)
(vl-load-com) (defun near_vertex_arr (obj / dxf_obj e_next obj_vlax pt_sel par pt_first pt_snd i bulge) ;bruno.valsecchi
[Code]....
How does everyone else hande this? By they way... I dont care what language it is written in :-)
i have problem with the Application option settings for sketch enviroment: When i draw a line in the sketch, i am not able to do the "click hold for a tangent arc to the representing line" it just starts a new straight line.
I know it has something to do with the settings, but can figure out what the correct settings are...
Why can't Inventor constrain an ellipsoidal contour with a line? We have pressure cylinders which uses a 2:1 ellipse. These cylinder get welded to a base stand fixture. The surface of the ellipse nestles in between contact points of the base stand, in this case lines of geometry. Yet Inventor can't constrain them as such. Any good workflow (at the assembly level) so that we don't have to ground components and use the Analyze Interference tool to make sure we are right on the surfaces? I don't understand why it will work for a cylindrical surface but not an elliptical surface.
I need to snap to guide lines but the only snap I can get is to the endpoint, which results in some very diagonal lines. I actually have ortho turned on because I need only 90 degree angles. Sometimes I need to move an entire line and I would like it perfectly lined up to the guideline. The line being moved is part of a polyline.
I sometimes do need to start or end at an endpoint but how do I do that then also snap to just anywhere on the guideline while maintinaing a 90 degree angle?
Currently there are a total of 3 viewports in an L formation. The fourth viewport, will go in the upper right. But first, I have to get these aligned.
I think the viewports themselves are fine enough. The problems arise because the model is in Model space so, construction line (as far as I can tell) didn't want to snap to a line, (on the model,) in Paper space.(vertical or horizontal) So, I can only see the construction line, in one viewport at a time. Which means, the construction line is not visible in the viewport immediately to the left. So, I can't extend the construction line across both viewports, to to snap them to the construction line.
When trying to place a construction line through an intersection the line offsets depending on where the cursor is placed. When the on screen prompt ask to specify through point. It defaults to 0 and I enter in 45'. It comes back invalid. believe this is a snap setting somewhere but I cant seem to find it.
I have autocad 2011.I am trying to get my autocad to snap to the closest line.
I draw a pline at a 45 degree angle. I press enter and I click the starting point again (in this instance the bottom point) and I draw another line near the other one, the nearest snap indicator shows up, but when I type "2" (units in Meters) and press "enter" the line is drawn where the cursor is and not along the 45 degree angle.
My goal is to get the second line to follow the first line with a different length.
How do I snap my new line to the edge of another object? A workaround is drawing the line over the object, and snap the point back using intersection snapping. I hope you understand.
I must not be the only one required to produce 2d dwg's for work.
I'm using INV 2009 and our vendor swears up and down in 2012 every thing is fixed, which somehow I doubt since they failed to fix the conversion from idw to dwg in the previous 12-13 releases.
Anyways, my problem today is that the dimiension lines I spent so much time making them meet our industry and company standards in my idw are all wrong in the dwg's I saved.
I want to join a couple of lines with arcs. Unfortunately I have got a dxf created with CATIA. When I try to join them with pedit it does not work.
If I move the end point of the circle away and snap it back to the line, I can join them. Blending the Curves together is working (this shouldn't if the endpoints match, right?)
You can see it in this screenshot:
(On the left the circle and line are joined after I snapped them together, on the right they are connected using "Blend Curves" as you notice the tiny white connection)
So here it leads to my question:
Those lines seem not to be lying end to end together so I can join them. Is there a function to snap them together or to automatically ignore/fill such a little gap?
I'm not sure what i changed but when im trying to sketch a line usually the little cursor turns from yellow to green when it snaps to an edge or a center. but its not snapping, how to get my line snap back.
Is there a setting I can change so if I am drawing an object (line, polyline, etc.) if I am snapping to a contour line, the objects will NOT take on the elevation of the contour line?
