I’ve an already drawn inclined line from a fixed point (saypoint (0,2) on Y-axis). The inclination is also fixed (say 150 tothe horizontal). My objective is to draw a circle with one quadrant at a fixedpoint (say point (1,0) on X-axis), so that, the line becomes a perfect tangentto the circle. The diameter of the circle may vary to make the line perfecttangent to the circle.
View 9 RepliesI have 2 points and a line given (both points on one side of line)
I want to draw a circle so that it passes through two points and tangent to the given line.
I need to find the center of a circle that is tangent to another circle and a point on a line. I cannot use tangent tangent radius.
View 4 Replies View RelatedI can't control the location of a 3rd circle using ttr. I'm drawing two circles and then a 3rd tangent to both but I want the 3rd circle to be centered down below the two original ones and all it will do is be above them. See drawing.
View 9 Replies View RelatedI'm having a problem, How can I draw a circle which has to go through point & tangent, if I know radius?
View 4 Replies View RelatedHow to draw an arc tangent to a circle and a point. The attachment here is a detail of the problem I'm having. No 9
View 3 Replies View Relatedhow do we draw a tangent line in autocad
View 1 Replies View RelatedI am attempting to keep the cable line of the crane always tangent to the circle at the top of the crane. The length of the crane (including the circle at the top) is being polar stretched but i am unable to keep the cable tangent to the top circle as i stretch and rotate the crane.
View 6 Replies View RelatedI am a new user of Autocad LT and looking for drawing a tangent line to a point on a circle.
View 7 Replies View RelatedWhat are the commands to make a tangent line from one circle 90 degrees to the tangent line of another circle?
View 2 Replies View Relatedhow to drawing a line tangent to two circles in C#?
View 7 Replies View RelatedI was wondering the best way to draw a circle that passes through an endpoint of a line and then is tangent to another circle above it? I need to create a radius of 3.5 between the two points.
View 9 Replies View Relatedgood way to start a line at one of the 45 degree angles of a circle block?
View 9 Replies View RelatedHow to draw a tangent to any curve(basically a spline).
View 9 Replies View RelatedI need to draw an arc that starts at a specific point, ends tangent to another line, and has a specified radius. What's the best way to do this?
View 3 Replies View RelatedIs there a way the “Osnap” can “feel” the tangent of the "circle point style"?I’m wondering if there is a way that the “Osnap” can feel the circle “point style” (given in the screenshot below) such that it is snapped to its tangent?
View 2 Replies View RelatedWorking on Acad2012 3d Civil. I draw a circle of 4000' radius and another one of 2000' radius. I put a tangent line between the two circles and I do see the tangent symbol but when I zoom in real close, it's not. So now I can't trim the excess radius of the two circle. I do have a trim line pasted the two supposedly tangent points. Is this a CAD issue or is their a variable to change that actually makes the lines tangent.
View 8 Replies View RelatedHow does one draw a line tanget from the end of an arc.
I noticed the tangent snap stops at the end of the arc but one can still place a line beyond the end of the arc, thus no longer tangent.
tan.jpg
i want to snap this line to where it would be at a tangent to the arc (as right), but as you see (left) when i hover with TAN snap it picks a tangent from the pick point, not from object's orientation.
at the moment i construct a tangent by rotating a copy of my line by 90°, and snapping it to centre of the arc. then extend out past arc, where the intersection is now the point i originally wanted to pick. make sense? gotta be a better way!
how to get a line to form a tangent on 2 different circles, different sizes, different cntr lines. Got snap on, but still not right.
View 4 Replies View RelatedI need to lable the delta of a PI in an alignment where one segment is an arc and the following is a non-tangent line.
Geometry points don't offer delta and Tangent Intersections won't label at PCs and PTs.
Is there an expression that can be used?
When inserting a DIMRADIUS in older versions of AutoCAD, the extent of the radius dim used to automatically stop at the tangent point along an arc. However, now in ACAD 2013 (and possibly other recent versions), a red 'extension' line is carried on beyond the tangent point, which I don't want. Is there a toggle that switches this off so that the radius dim stops wholly at the tangent point as before?
I've tried using endpoint snap to stop the dim at the tangent point, but the radius dimesion text is then placed on the outside of the curve rather than the inside where I want it.
I am trying to create a dimension in an .idw that goes from a line to the tangent of the outer diameter. I have tried several approaches but I cannot get it to work. Essentially I am trying to replicate a drawing which was created in Solidworks but I am having trouble with this dimension.
View 4 Replies View RelatedHow to correct length line Tangent Edges, Foreshortened (sheet metal drawing) ? I didn't find option to correct length line Foreshortened (sheet metal drawing) .
View 1 Replies View RelatedWe have a need to select a tangent line/polyline etc and then select two other points we would then like to have the program draw an arc through the two points and yet still be tangent to the initial line/polyline that we picked. We don't care what the radius is as we believe there is only one solution anyway. It would be wonderful if we could just use the Arc command and select start>Second Point> then just use the Tangent Osnap but I guess that is out of the question :-)
The only code that I have come across that even resembles this only allows for one point not two (STILL VERY HANDY AND VERY SLICK)
(vl-load-com)
(defun near_vertex_arr (obj / dxf_obj e_next obj_vlax pt_sel par pt_first pt_snd i bulge)
;bruno.valsecchi
[Code]....
How does everyone else hande this? By they way... I dont care what language it is written in :-)
i have problem with the Application option settings for sketch enviroment: When i draw a line in the sketch, i am not able to do the "click hold for a tangent arc to the representing line" it just starts a new straight line.
I know it has something to do with the settings, but can figure out what the correct settings are...
Why can't Inventor constrain an ellipsoidal contour with a line? We have pressure cylinders which uses a 2:1 ellipse. These cylinder get welded to a base stand fixture. The surface of the ellipse nestles in between contact points of the base stand, in this case lines of geometry. Yet Inventor can't constrain them as such. Any good workflow (at the assembly level) so that we don't have to ground components and use the Analyze Interference tool to make sure we are right on the surfaces? I don't understand why it will work for a cylindrical surface but not an elliptical surface.
View 7 Replies View RelatedHow to draw the involute of a circle?
View 1 Replies View RelatedHow can i draw a SPRING around a circle ? like Attachment picture. (not in the Sketch) in the Part Modeling.
View 1 Replies View RelatedHow can i Draw a SPRING around a circle ?
View 3 Replies View RelatedWhat is the smallest object I can draw and "SEE" in AutoCAD? I was hoping to prove a point in my introductiory AutoCAD class, but it appears I have been lying!! I tried to draw a cirlce with a diameter of 1.24E-10m. The dot shows up, but I cannot zoom to it. I tried using an enormous zoom scale, but did not have any luck. I am almost positive my instructor introduced the capabilites of AutoCAD by drawing a full scale helium atom, and that was release 14. Is this still possible? Obviously the atom can be drawn, but what are the zoom limitations?
View 5 Replies View Related