AutoCad :: Scaling Annotations And Plotting To Scale In Millimeters?
Oct 16, 2011
First, when I have a drawing to scale in millimeters and want to put its attributes, the amnotations come out extremely small. It's caused me so many headaches. the units have been set to millimeters, limits from 0,0 to 200-150 ish. Drawing a small drawing within those limits tried very, very small annotations that you can't see unless you zoom 200 times in. I don't have that problem when drawing in inches though. Annotations come out great in inches.
The second problem is that, after I complete a drawing in millimeters and I want to copy and paste it onto my template (also drawn in millimeters to fit a 12-9 paper) the drawing comes out HUGE. At least 100 times bigger than the 1:1 scale should be. When I draw and plot in inches, the 1:1 copy onto a template comes out perfect, but for some reason it always does that in millimeters. I tried placing a block over the template with the "model" to scale and that looks closest to the proper 1:1 scale. I double checked on both the drawing and the template that their 1:1, they seemed fine so I printed. When I measured with a ruler it was still off by a bit.
What I can do to make annotating and plotting in millimeters as easy as with inches?
View 9 Replies
ADVERTISEMENT
Mar 22, 2013
Is there a way to change the annotations so that they become millimeters and not meters?
I dont really want to change my entire drawing to millimeters because i have other drawings in my model space which suit meters. It's just this one section I have drawn is so detailed and zoomed in, it really should be in millimeters.
If there isn't i'll just change the whole drawing, but thought I should ask on here first in case I was missing something obvious
View 9 Replies
View Related
Sep 4, 2011
If I used millimeters as my UNITS, how can I scale them when plotting it into A1 or A0? How will I know the scale that I will use in Layout tab so that it will fit on the paper that I will used?
View 9 Replies
View Related
Apr 23, 2012
When plotting profile plan sheets, there is an error in the scaling of the grids. I can not seem to figure out why the plotter is not plotting correctly. I did try creating a pdf of the plan sheet and plotting, but still have the same scale error. It starts to get off scale after about 500 feet, so the error in scale is small, but still there. It is off by about 2 or 3 feet at 500 feet on the profile grid.
View 2 Replies
View Related
Sep 22, 2009
I am using the dinosaur version of autocad 14. I know it is old but is working great for what I want to do. I learned on 12 and was using 14 when I stopped working 10 years ago.
I am having trouble scaling my drawing. I remember that 1/48 xp is 1/4" scale. 1/64 ?? is that 1/8" scale?? 1/24 is 1/2" scale.
View 9 Replies
View Related
Jun 12, 2013
Im working for a geological firm that use timescales to describe their work (depths at times etc). I need to compress the time bar but not alter the text but cant find way to do it. Im only scaling in 1 direction.
View 4 Replies
View Related
Dec 27, 2013
I am still confused when it comes to My units and plotting to scale. If I want my drawing at 1/8" scale what would I set my units to and what would I set my scale to when plotting?
View 2 Replies
View Related
Oct 17, 2012
I have a drawing (attached) with the following settings: LTSCALE = 1, MSLTSCALE = 1, PSLTSCALE = 1.For some reason the linetype is not scaling based on the annotative scale. It will update correctly if I change the LTSCALE but for some reason it wants to ignore the MS and PSLTSCALE variables.
As a note, the drawing was converted from a Microstation drawing and the linetype is a converted Microstation linetype.Is there something in the linetype that is doing this.
View 6 Replies
View Related
Sep 17, 2012
So I create a block on layer 0 and then create the block as a 1 inch by 1 inch block so it is easy to scale up to the size I need but when I try to insert the block at the scale I need it wont resize it to the correct scale. It stays at the 1 inch by 1 inch original block.
View 1 Replies
View Related
Dec 6, 2012
I use AC 2013 LT.
1)When switching between the Drawing and Annotate option to the AC Classic option a menu would appear with options to use the civil menu, mechanical or architectual. This has now dissappeared and I do not know how to acces it again.
2) Coming from a manual drafting background scaling appeared to be easier. I want to change the template scale shown in the title block from 1:1 to 1:5. This seems to be able to be done as it is highlighted. All my efforts save to enter it hard does not work, but this does not change the sheet scale. Changing the scale on the menu bar does not affet the sheet scaling
View 4 Replies
View Related
Apr 2, 2011
I have drawn a 2D 'ruler' 250 units by 50 units and drawn 10mm marks along the edge of the ruler with the last section divided into 1mm marks.
When I plot the drawing, setting the scale in the properties box to 1:1 or 1:2 (or whatever scale I choose) then selecting File, Plot etc, (leaving the scale in the 'Plot Scale' section of the dialog box as shown - normally 1:1) the resulting plot is slightly smaller than expected. What should be say 200mm is more like 199 mm.
I am using AutoCad 2007 and a local domestic type printer (HP type) connected via a USB line.
View 8 Replies
View Related
Jan 25, 2011
I am putting together a catalog with some drawings from AC 2010. I am drawing in model space and printing in paper space. The view port scale is 1:1. If I print directly from Autocad to the printer, everything is fine. If I first plot to PDF from Autocad and then print, the dimensions are off by about 1/8". The dimensions read correctly, but they do not measure correctly. The paper size is 8 1/2 x 11. I would like these PDF files to be accurate in case someone needs to print them.
I have tried saving to dwf and then printing and printing out of Design Review but it doesn't make any difference. My settings in Adobe are 1:1 as far as I can tell.
View 9 Replies
View Related
Apr 15, 2011
I am attempting to plot a site plan for a large single family home property (2 lots at 200'x329') to an ARCH D (24x36) sheet and have set up the paper space and a title block template to fit this. I set up a new viewport inside the tile block template to take up all the open space inside it.
Our professor provided us the survey from which we're doing our drawings and has asked for us to plot in 1:20 scale(1"=20'), so I have input 1:240 (1" = 240") in the layout scale menu. The site plan to be plotted fits, but much too small to be acceptable. It takes up only maybe a third of the viewport, when it should fill the viewport (the sheet) for the most part.
View 1 Replies
View Related
Jun 26, 2012
I love annotative scaling of objects it is a great feature. I am however having one problem that I'm not sure if I've missed a setting or something. Is there a way to prevent civil 3d from scaling your annotative objects based on the view scale you are looking at? For example if I zoom out (in model space or max viewport) to show my entire drawing and regen, civil 3d scales all my text and blocks to an enomous scale esentially blocking my entire drawing with solid colour. also if I zoom into a small area to do some detail work all my text becomes microscopic and unuseable. This makes adjusting text so it doesn;t overlap other text very difficult if it never appears at the correct size. Is there a way to freeze annotative objects at thier correct scale (for the current viewport scale) so they dont scale simply because you zoom in or out on a drawing?
View 3 Replies
View Related
Sep 25, 2012
when i go to preview plot after selecting D size, scale isn't correct. how do i change to correct scale for plotting after i've scaled each view in paper space. please see attached drawing.
Any good free tutorial online about viewports and plotting from them and to get correct scale?
View 9 Replies
View Related
Mar 13, 2013
I've got a question about plotting to a measurable PDF with the correct scale.
Currently, if you plot to PDF (ARCH full bleed D 24x36 paper size) using 1:1 scale of the Layout area (including viewport, title block, etc) you get a nice PDF of the appropriate plan which would print to paper at the correct scale (1/16" = 1' 0'). If you set the plot scale to 1/16" = 1' 0' then preview/plot it then it appears completely tiny (like 2% of the page size), in the bottom left corner.
However, I want to make the PDF measurable. At the moment, if you do this using a 1:1 plot, the default numbers given by the measure tool are way out of proportion (a 29' dimension in the drawing is measured as 48,294 with no units). To get it to give accurate measurements, you have to tell Reader/Acrobat to ignore document scaling in preferences, then "Change Scale Ratio" to the appropriate scale ratio (0.625 in = 1 ft). This means you can measure to scale in Reader or Acrobat BUT these options disappear once you close Reader/Acrobat.
creating measurable PDFs from Autocad plots?
View 4 Replies
View Related
Aug 9, 2011
My drawing inb model space looks fine, however when I try to set it up to plot in paper space, via the properties box with the "correct scale factor" and the drawing becomes very large. The only scale I can get the drawing to plot at is "fit to page", which is no scale. I have tried to set the scale on the "page setup" and the same thing happens.
View 5 Replies
View Related
Aug 21, 2012
I'm trying to plot a simple site plan to PDF through the DWG to PDF.pc3 option.
The scale in my model space is 1-1 and in my viewport in paper space 1-200.
The issue is I plot to PDF, and then the scale is way out. For example an object that should be 10,000mm long in model space appears as 59mm (11,800mm scaled) on the PDF. And of course when I print from the PDF to a printer this scale error carries over.
View 4 Replies
View Related
Aug 20, 2013
When trying to scale the print size, after clicking inside the scale box, the sizes just keep increasing, even though I never got a chance to enter anything.It just keep getting bigger and bigger. How do I turn this "feature" off?
View 3 Replies
View Related
Sep 27, 2013
Any way to get a scale bar/title block text to reflect plotting at half size?
We use the common (24x36) sheet size for all projects, but when plotting we send out half size (12x18) as well. This means the scale bar reading 1"=40' is no longer correct. It should read 1"=20'. I would like to automate this.
View 6 Replies
View Related
Aug 23, 2012
I'm designing some photo frames and as they come in loads of different sizes, I'd like to be able to make the frame design bigger, in illustrator, but keep the width of the actual border. i.e. at the moment it's for a 10cm x 15cm photo with a 3cm wide border going all the way round - I want to keep it 3cm for larger photos.
and here's a link to the .ai file: [URL] I have loads of other frame designs which will need similar treatment so I'm looking for a general solution rather than something that is totally specific for this design.
View 5 Replies
View Related
Dec 15, 2011
I have this problem with units. I am using 2012 Autocad drafting. I want to work with millimeters, for instance usually when I type 1000, that is usually refereed as 1 meter. Now in the new model space when I type 1000 the line is so long, I even have to press regenerate so that I can see the line. I checked the units, they are set to millimeters, I also checked from options - user preferences they are also set to millimeters.
When for instance I will open an older file that I worked on in autocad 2010, in autocad 2012, it will work fine, when I will write 1000, it will actually come up as one meter. The settings in units and options - user preferences are the same.
I also copied a table from the 2010 file to the new one, and the chair comes up very big in the screen, so again I use regenerate to zoom out.
Also every time I open a new file, I have to go to units and change it from Inches to millimeters. Is there a way to do it once, so that you don't have to do it every time you open a new file in autocad? I know you can customize your workspace, and I have, but that doesn't seam to do it.
View 7 Replies
View Related
Nov 28, 2006
I have some drawings that are drawn in millimeters. I need to add to the drawings but when I type 36 I get a line 36" long. I need to change autocad so that when I type 36 it draws a line that is 36mm.
View 9 Replies
View Related
Oct 11, 2013
I am trying to set up a METRIC project (that I want to make template) that uses meters instead of millimeters.
So I created a new project, without the use of any template. I copied from the default Autocad templates folder the Model and Sheet templates to the new project folder and I set the units, scale and grid to meters and changed the path in project properties to these files.
Everything seems to work fine, except creations of sections/elevations.
I edited the SectionStyles (Metric).dwg file in default styles folder and It works fine.
But I donțt want to change that file in the default folder, but to change the path of the section styles in the project. The only way I could do that was to change it in the tool palette - right click on callout.
So how can I make the SectionStyles to load from a specific location for a project without having to right click on every callout that I want to use and change it manually?
There are some other things to do/change for making the project template that I want? (I am referring to the units setup).
View 1 Replies
View Related
Dec 30, 2013
Is there an easy way to add the superscript "2" to a note for Milli meters squared in Inventor 2010?
Example: mm2 or FT^2
View 4 Replies
View Related
Jun 30, 2012
By a mistake i have drawn my drawing in millimeters. Thus when i print it in 1:1 it is to small .
And when i click on my block and go to properties, I can't change the block unit it is grey market. is it possible to change that in centimeters ?
Block unit.JPG
View 7 Replies
View Related
Oct 24, 2011
I am trying to make a PDF file out of a Layout to accompany the DXF files to a client, but when I create the file, all the annotation is missing. I have created such PDF's in the past and they worked fine, so Im scratching my head as to why it doesnt work now
I have attached the files so that this can be seen.
View 3 Replies
View Related
May 3, 2012
I have Autodesk Inventor on a student license, and I use the metric system.
I've been able to change the settings for parts, presentations and assemblies to use millimeters, but for some reason the drawing sheets still use inches.
How do I change the unit settings for drawing sheets?
View 5 Replies
View Related
Mar 27, 2008
How could i know if i'm using meters, and not inches, feet or millimeters? and how to set autocad to use meters not inches, feet, nor millimeters.
View 9 Replies
View Related
Apr 6, 2012
We have conducted a 6" x 6" grid survey of a building's finished floor and the client has requested the output drawing of the point file survey to be shown in Millimeters. The Point Label style in Civil 3D 2009 only has the option to show Meters which isnt precise enough for the clients wants. I am using the metric template in autocad Civil 3D and all units are set to metric.
Is there a way to change you point label to show Millimeters?
I am using Civil 3D, Update 3
View 3 Replies
View Related
Nov 5, 2012
I've been using cad for a while but only for simple layout drawing for parts I need made.
Autocad 2010 I want to set up a drawing to draw some manifold adapter plates in millimeters. I can set it up for inches but I'm having a problem setting up for mm. I start a new drawing and select the template initial setup-manufacturing-metric.dwt In drawing unitDecimal and precision is set at 0.000 Units is set to "millimeters"
I draw a circle to test it. I draw a circle of 5 radius. Should be a circle 10mm in dia, correct? But it is huge, my guess is that it's 10 inches. I'm basing the size on what is printed out when I set my print to no scaling, 1:1, plot window. The same as I have for all the drawings I do in inches.
Second question.
How can I get circle centers to show on prints without actually drawing them or putting in dimensions?
View 5 Replies
View Related
