I was wanting to save my toolbar setup and commands,or the way my screen looks. Do you do that in the options, profile section. If so do you just name the current screen shot as something and export to safe place.
View 8 Replieswe are using A2011, Classic workspace (toolbars) and i have partial menus loaded (custom toolbars).
If i try to add a new toolbar to a custom toolbar, or to add buttons to an existing one, the changes are not saved when i close the customization window.
I am trying, in vane, to batch plot multiple dwg files to pdf's.
I have a pdf reader/writer (Bluebeam Extreme), but the plugin will not work (I have sent an email to Bluebeam to see if hey can sort it out).
So, I tried using the batchplot, but kept getting stuck when I had added multiple dwg's, using Publish, and then tried to change the page setup by right-clicking the files. The new page setup I had just created wass not available, apart from the dwg I created it in.
I hadn't notcied until now, as I usually use the Previous Plot dropdown when plotting, but whenever I create a new Page Setup, it is no longer in the dropdown combo box whenever I open up a new file, or even in the file I created it in if I close it down and reopen.
I am using AutoCAD LT 2010 with Windows 7 Professional, 32 Bit.
I didn't like the name of my custom Pulldown that I made:
DSI-Menu.cuix
I Did a Save as:
DSI-Menu_sc.cuix
All the custom Commands list the original DSI-Menu as the source. Can I somehow change that so that the source is DSI-Menu_sc?
Is there a way to set up batch plot so it saves the files on it's own? Right now I have to wait for the box with the name to pop up and then I hit OK and then have to wait for each file like that?
I found a setting and changed it from "Prompt for name" and changed it to "Specify Name" but that did not do the trick.
Is there a way to save a setup in Action so that I can use it again in another Action composite? What I'm looking for is what ConnectFX Clips do in Smoke2013. I have some 3D models, connected together with Axis and some bkgd elements that I'd like to use over and over again in different Action composites. I'd like to just import those setups (models etc.) into new Action composites. Is this possible?
Smoke 2012 SAP2 SP3
how can I save Node Setup in CFX with PreRelease 3
View 1 Replies View RelatedIn our drawing office we use Inventor in a mining materials handling environment. Our output is mainly structural drawings where we require a bill of materials as part of creating a drawing. Whenever I insert a BOM in the drawing environment I get this table which is labeled in a foreign language (it looks like an Eastern European language) and the format is not as per the standard Autodesk installation setup.
How do I either revert back to the standard setup or do a BOM setup from scratch?
We use IV 2013 Professional on Windows 7 64 bit.
Is there a way to save a custom artboard setup with a custom document profile in illustrator cs5? I do technical illustrations and our page size is odd (7.19 x 8.96. It the size that our Framemaker layout is set to.). I have a custom document profile that I use, but I use the grids all the time so that my callouts are spaced out evenly around the art. I would like to have a way to set the artboard up so that the grid will align to the center of the artboard everytime I turn them on. Right now they always start from the top left and when I center art in the center of the page, the grid spacing isn't the same on each side of the art. I just want to be able to open my document profile, turn on my grids, have them start from the center, and I can get down to business. As it is now I have to go into my artboard settings and manually adjust the grid to the center. Small annoyance, but it still annoys me. I have tried to save it a few different ways, but nothing has worked. Maybe there just isn't a way.
View 4 Replies View RelatedI'm running Design Suite Ultimate 2012, windows 7 64bit, I can launch IV 2012, but I can't seem to see my tool bars...
View 9 Replies View RelatedI am wanting to save all of my menus, toolbars, templates etc. so I can put them on my new computer. I am using autocad LT 2010. I have looked everywhere for the files on my C drive and can't find them anywhere. On other versions I could copy them to a flash drive and then onto another computer. I tried going through the user interface but I couldn't get anything to save. It did make a .cui file but I didn't know where to copy that to on the new computer.
View 1 Replies View RelatedMy autocad toolbar are not showing......
I have checked ctrl+0 option.......But this is not working and my toolbar are not showing
When I try to menuload a .cuix on a machine that has UAC set to high, The menu group comes in, but the toolbars associated with it do not. I know this sounds like AutoCAD support but it is .net related as the .cuix is loaded through .net. The pull down appears OK.
If I manually set UAC to it's lowest setting then they come in, is there a reason for this?[URL]
opened autocad 2014 lt today and all my toolbars are gone, as well as alot of my shortcuts.
View 3 Replies View Relatedas title says. using acad 2010 in classic mode. had to switch to ribbon but i dont like it as much
View 5 Replies View RelatedI need to add toolbars in 2d annotation ???
View 2 Replies View Relatedas above.....desperately trying to find them.
still got dashboard, palettes, design center and properties but absolutely NO toolbars.
Is it possible to put only specific command buttons from the toolbars on my interface while excluding others.
View 4 Replies View RelatedI have just downloaded trial verion of AutoCAD for Mac, onto new Macbook Pro.
The two palettes are there on the screen left hand side, but I cannot find the classic toolbars, which I cannot work without.
Just started new job, with PC running ACAD2010. My toolbars appear blank, with no icons. How do I get the icons to show?
View 4 Replies View RelatedI'm about to throw a chair through a window!!!! I just simply and accidentally closed all of my toolbars... just "un-checked" them in the general gray-area right click drop down.....couldn't figure out how to get them back..... read a few cadtudor posts.....started doing advanced stuff like "menu load" and "toolbars load and reload"..... now I'm completely messed up: no menus at all and no toolbars!!
View 4 Replies View RelatedI have a dual monitor setup and I maximize acad2011 on monitor 2 and have my toolbars on monitor 1.
I like to have my toolbars floating, but justified to the side with the 'gap' between the montiors so the tool bars fly out and I can see my email or reference docs or whatever on monitor 1 also. Sadly every time I close and re-open acad my toolbars re-justify to the center of monitor 1. I've tried unlocking and locking but that doesn't work. I am using the 'better', errr, excuse me, 'classic' workspace.
I made some toolpallets and i want them to share with my collegas. I know that i can export them amd then import manualy, but is it possible to set the files of the toolbars on the server so if i change anything everybody has the same?
I dont want to import and export them everytime i change something.
I have the Layer Property Manager and Properties toolbars docked on the left edge of my screen, with the Ribbon vertically between them and the drawing display. I sometimes 'overshoot' when going for a command from the ribbon and the toolbars pop-up immediately so that I then have to move the cursor back into the drawing space and wait for the toolbar to collapse before I can pick the command (more carefully). Is there a way of setting a delay on the tool bars appearing?
View 9 Replies View RelatedI can't see any of the inventor toolbars anymore.
if i would still have the Quick Acces Toolbar this wouldn't be a problem but that one is also gone.
For years we've had a line type change toolbar that worked just fine. This years update may have changed something that the old macro is missing or doesn't need anymore because none of the commands work anymore. One of the macros reads:
^C^Cselect chprop;previous;;ltype;dashed;ltscale;4;;
I have just updated to 2013 LT. I want to customize my toolbars to match my old set up but once I've spent ages moving tools to new folders and arranging them how I like it, I close Autocad then open it again and it reverts back to default so all that time editing folders etc is wasted!!
View 2 Replies View RelatedWe have the Cardinal Toolbar and the Layer Properties Toolbar (one that allows you to toggle between layer groups ... for example floor levels) installed on our AutoCAD LT 2006 software for a PC. We are looking to purchase AutoCAD LT 2013 for a MAC. We have downloaded the trial version, and cannot find these toolbars on the new version. Our files are set-up to function with these toolbars. Is there any way to download these toolbars for the new version? If not, are there commands we can use to change the cardinal direction in model space and to toggle between floor level layers (groups?)?
View 1 Replies View RelatedA client is experiencing a problem whereby when he runs his software,Inventor Professional-Autodesk Product Design Suite 2013, he gets the blurred toolbars as in the attachment.
View 1 Replies View RelatedI'm old school trying to learn new school! I love using my custom toolbars and abbreviations from the keyboard for calling my autocad commands. I am in the process of learning the uses of the ribbon. I have always used the acad menu, then loaded "partial" custom menus. Is this still possible using the ribbon? Not sure how to do this. I like keeping the custom stuff separate, because we have 5 users with a standard company menu and I like the idea of always going back to the original menu. I suppose my question is how do I use the ribbon, and continue to use my partials also
View 7 Replies View RelatedI am having trouble editing existing imported toolbars. Also, I cannot retrieve my custom toolbars into 2012. When I convert older menus (mnu) into 2012 the tool bars all have question marks on them, and my custom toolbars are not listed. I cannot go into CUI customization and click on a button to edit it's command and or icon. The older version of cad is not on my new system so I cannot use the migration tool.
View 9 Replies View Related