So I have set camera view in my viewport for a perspective view. This goes okay but when i close my drawing and open it again.The view was changed. I have tried locking my VP, set UCSFOLLOW to 0, display locked=YES as stated on other VP problems in threads. What setting am i missing?
View 2 Replies“Locking” the layers state (turned on/of frozen/thawed/ locked/unlocked, etc.) in the viewport,
I’m wondering if there is a technique that allows locking the “state” of layers (turned on/of frozen/thawed/ locked/unlocked, etc.) in the viewport mode such that the viewport will keeps its required state REGARDLESS THEIR STATE IN THE MODEL MODE!
For example, in the screenshot below, freezing the point in the model mode will also freeze them in the viewport! And thus the layer state are not kept as required in the viewport which adds more efforts.
One possible option is saving the layer state! But this feature is not a property for the viewport but needs to be selected from the layers option. And thus we need again to think about layers that are supposed to be turned on/of frozen/thawed/ locked/unlocked, etc. in a particular viewport.
What I need here is to LOCK the viewport not only in terms of scale but also regarding the state of layers!
I have added an image plane to an existing newsroom set. I would like to 'lock' the image plane to the camera so that it doesn't 'slide' when panning/moving the camera. Like a corner pin per se.
View 5 Replies View RelatedI am using Inventor 2012.
I created an assembly in Inventor and now I am creating a drawing for it in Inventor. I have a few views placed of the same assembly.
Is there a way to lock one view in the assembly? For example, my assembly consists of a door, I would like to have one view with the door open and another view with the door closed on the same drawing using the same assembly link.
What associative links are removed when locking a design view representation? Hopping IV 2012 will have representations working the way they did back in IV 2008, my BOM'S and views both played together quit nicely when creating installation drawings.
IV 2010 64bit
i have a template, created a viewport and fit the model view in the layout space. However, when i scale the template... the viewport model doesn't follows the layout scale. Is there any ways to fit it so that when i scale the template i don't have to set the view again.
View 8 Replies View RelatedLet’s say you have a large building plan in model space but there is only one small area of the building that the view port is looking at. Is there a way that you can draw around that viewport and then take that into model space and paste it in the same place so now you have the same area located in both views?
At the moment I need to try and work out where the view is by drawing a rectangle around the correct area of the building and this is time consuming.
I could then trim/delete everything else outside that box.
even in an empty scene my framerate in the quad viewport is about 7, 8 but in single view its 30-40..
I'm a little unsure if it was low like that before and I just realized now or sth. has changed. (Guess it has not been so slow as its really annoying) Using latest NVidia drivers and a 3DConnexion Navigator with 3DS Max 2013.
Why Camera Views is different from all other views in Revit. It is simple not possible to add a view reference, or a tag etc. to reference to a camera view.
Of course I can put in a 'dead' symbol to show where it is in plans, but that's simply not the same...
leaving the isolate mode in a camera view (3dsmax-camera or vrayphysical-camera) changes the view from cameraview to perspective view. Am I missing any new setting or ist this a bug...
View 3 Replies View RelatedThe same keys seem to be used to move the viewport camera, but the behavior of the viewport camera seems to have changed. For example, press Z to focus on an object, middle-drag the camera off to the side in one direction, and alt+middle-dragging used to just rotate the viewport camera around a new focus point. Now, it's almost like the viewport camera is getting swung around on a rope around the original focus point.
How can I change it back to the original way?
I have a problem with one specific drawing where I have created a right viewport; however, if I double click in the port to enter model space, the viewport automatically changes to a top view. If the viewport is locked, no change to the view. This problem only exhibits itself in one drawing so it must be some setting that is drawing specific.
View 1 Replies View RelatedI have completed an elevation view and made a viewport to view it in paperspace. I want to make another viewport and rotate the view so that the area where the elevation view was drawn is aligned with the elevation view.
View 9 Replies View RelatedFor some reason I've lost my viewport camera settings in all viewports, and polycount (7) ive reset my UI but nothing?
View 9 Replies View RelatedIn the 3D viewport, lets say there is an object to my left. How do I turn the view camera to look at it?
View 4 Replies View RelatedI have code that has the user select a viewport. I then need to set the selected viewport to an existing view, but I cannot find any exampes of this.
I have the viewport, but how do I get the ViewPortTable/ViewPortTableRecord from it?
Do I need to set the view in the ViewPortTableRecord od the ViewTableRecord?
No problems to this point...
'Code snipIf acPrmpt_res.Status = PromptStatus.OK Then
Dim acVPort As Viewport = Nothing
Dim acViewTbl As ViewTable
Dim acViewTblrec As ViewTableRecord
[Code] ........
I am trrying to rotate the view that I have in my viewport. I used to use a command that had the options Alingn, rotate etc but in this moment I do not remember that command. I you do not remember either
View 6 Replies View RelatedWhen I use the SSM and use the "Place on Sheet" command to create the Viewport from the MS View DWG file, it comes in only as a rectangular Viewport. I tried to see if there's a way to draw a Polyline and select it as a MS View but I don't think that's possible.
Any way to do this without breaking the link between the View DWG and the Sheet DWG?
I need to rotate a view through a viewport in paperspace and tried to use the mvsetup command but LT doesn't recognize that command. How I can do it?
View 5 Replies View RelatedWhen using "Create Multiple Section Views", some of the information is placed outside the viewport.
How can i get this information inside ?
How do you clean up areas where the section view is outside the viewport limits. C3d should have moved the top section to the next sheet becuase it didn't fit. How do you tell it this? An automatic toggle somewhere?
View 4 Replies View RelatedWe have a number of drawings, where the views in paperspace viewports are not orthogonal to the XY plane. Is there any way that we can adjust the viewport view to a TOP view (a view aligned to the XY plane) without changing the viewport scale?
If I activate the viewport and use either PLAN or View->TOP my viewport scale is destroyed, and the view is rotated along the Z-axis.
I've struggled with the old issue of shifting images in rotated viewports. We use georeferenced aerial photography by way of these images inserted into their own drawing and then Xreffed into another drawing for printing. The issue is, the image appears shifted in some viewports. Most of the time it prints fine but not always. I searched the discussion groups and found a post a few years ago that a reply user stumbled across a quasi workaround. When the view command's Perspective is turned on and then off within the viewport, the image appears to be locked in it's correct position, not shifted. I have successfully used this procedure several times over the years until now. I have half a dozen drawings that when I turn the Perspective on and then off in a viewport, the image will not display. The xref is loaded and the layer is turned on in the viewport but the image doesn't show. What is the perspective portion of the view command within a viewport?
View 2 Replies View RelatedJust switforeveched to AutoCAD 2013 from 2011. I kept the classic interface as I did since forever. This is the problem I am having now. After I created a viewport in a layout, I right click on the viewport border fully expecting a menu to come up so I can set the type to be 2d hidden. But nothing like that occurs. The help menu came up. How do I get the viewport menu to set the view type?
View 2 Replies View RelatedI have a site survey that I am having rotation issues with.
In the model space the drawing is rotated so when I draw a vertical line it points up (which is what I am used to). However in the paper space, the drawing is automatically rotated so that north is now pointing up, and if I attempt to draw a normal vertical line as i did in the model space the line now points NE.
How can I rotate the view of the viewport in paper space so that my lines as vertical and horizontal. This would not be such an issue if it was just a plan, but I have drawn sections that just look ridiculous.
I am working on a rendering on vanilla AutoCad 2013, and I am getting frustrated with having to reset my viewport to the named view every time I move my camera.
I know that when you create a viewport you can call up a named view, but is there any way to link it permanently?
Since I installed autocad architecture 2012 I have this problem. When I drag a view from the project navigator in a sheet I see the content and the option to set a scale. So far so good. When I click in the sheet to set the location the viewport goes empty. I can stretch the viewport to top left to get the drawing within range and then move it back to where I want to place the drawing.
View 5 Replies View RelatedWhen I pick rendered for my shadeplot on a viewport, none of the materials applied to multi-view blocks show up. Is this common or is there a fix?
View 3 Replies View RelatedA problem we are having in our office on 1 computer is that this message appears in the command line
'viewport is view locked switching to paper space'
It happens whenever we zoom or pan into one of our locked viewports. We have purposefully locked the viewport so we don't lose the scale when we zoom or pan and want to leave it this way, however, whenever we zoom or pan this message appears and it takes 30 seconds before the screen readjusts to the zoom or pan we require.
I have had this issue for about two weeks. I am not aware of any changes to my system though Windows 7 updates automatically.
Often, but not all the time, when I am in a floating viewport which is locked and I zoom in, the part of the drawing disappears as if the view on the viewport has adjusted to one side so that I cannot see any of what I am working on. If I escape the command and 'undo' last command it takes me back to the correct view but in paperspace.
This is a pain as I cannot zoom in to locate a point accurately. It only happens when I zoom in quite close. The viewports are locked and it is only a problem recently. I have used CAD for 20 years and LT 2008 for the last 4-5 years so I dont think it is a user issue. Maybe a settings issue or bug, but I have not knowingly changed any settings which would do this and cannot see why this would be a 'feature'.
What I am attempting to do is: add text, some dims., and some info. to a viewport i have added to a drawing for my field guys. I am a sheet metal worker and have produced a drawing of duct work. one viewport is a plan view, one is a swiso, and another is a left-elevation view. everything is good except the left-elevation view which I would like to add details to. I am assuming I need to change the ucs so that i can place lines, dims and text and get them to show up without them snapping to 0 z.
View 9 Replies View Related