even in an empty scene my framerate in the quad viewport is about 7, 8 but in single view its 30-40..
I'm a little unsure if it was low like that before and I just realized now or sth. has changed. (Guess it has not been so slow as its really annoying) Using latest NVidia drivers and a 3DConnexion Navigator with 3DS Max 2013.
I change viewport layout to quad from single and it will not save. I saved a new maxstart file and have followed all directions find in Max books.Nothing seems to work. I save and turn program back on and layout is back to single.
View 2 Replies View Relatedi have a template, created a viewport and fit the model view in the layout space. However, when i scale the template... the viewport model doesn't follows the layout scale. Is there any ways to fit it so that when i scale the template i don't have to set the view again.
View 8 Replies View RelatedLet’s say you have a large building plan in model space but there is only one small area of the building that the view port is looking at. Is there a way that you can draw around that viewport and then take that into model space and paste it in the same place so now you have the same area located in both views?
At the moment I need to try and work out where the view is by drawing a rectangle around the correct area of the building and this is time consuming.
I could then trim/delete everything else outside that box.
I've got an RGB image, but each pixel actually has identical R, G, and B values-- the image is just varying degrees of grey. (It's not actually a greyscale image, long story. :P)
If I click on the single channel view, it's much brighter than the RGB combined view. Each channel appears identical to each other channel, but they're all considerably brigher than the combined RGB image.
Do you know what adjustment is being performed?
(That's the short question; elaboration follows.)
Photoshop is aware of this adjustment, and will replicate it if you copy the RGB image and paste it into a single channel of a new image. For example, I can copy the entire image, create a new image, and then paste into just the red channel of the image. Visually, the combined RGB view of the source image and the single channel view of the dest image will look identical.
How was this achieved? Photoshop darkened all of the values: a pixel that was 24, 24, 24 in the source image is now 7 in the new red channel.
I haven't been able to replicate the conversion. Visually, it looks a lot like a gamma adjustment, and values in the middle range roughly approximate an adjustment using a gamma of 1.266 (which seems odd, so is likely not what's occurring). Values in the lower range, however, are darkened further-- a gamma adjustment of 1.266 will leave them too bright.
Recently I have come across a very big problem which has seriously inhibited my ability to texture a model in 3D Studio Max 2010. Upon importing a texture in .PSD format (so that I can change and update the texture map in Photoshop), first Max said four times over that it was an "incompatible PSD file" for some reason, and after it finally loads into Max, I can not see it in the viewport; it is just a solid white without any texture at all. It renders just fine, but I can't see what I'm doing without the texture in the viewport.
In the attached picture, the white part of the model indicates faces that have a texture map applied. The problem is that I can't see the texture in the viewport, and I need to be able to see what I am doing.
I have the "Show texture in viewport" button clicked on in the Material Editor. And I have also tried changing the preferences from Direct 3D to Open GL and changing the DirectX from 9.0 to 10.0--and that did not work.
I have a problem with one specific drawing where I have created a right viewport; however, if I double click in the port to enter model space, the viewport automatically changes to a top view. If the viewport is locked, no change to the view. This problem only exhibits itself in one drawing so it must be some setting that is drawing specific.
View 1 Replies View RelatedI have completed an elevation view and made a viewport to view it in paperspace. I want to make another viewport and rotate the view so that the area where the elevation view was drawn is aligned with the elevation view.
View 9 Replies View RelatedIn the context of an animated GIF, or any other context where I have a multilayer image, I would like to see a single one all by itself. How do I do that?
View 3 Replies View RelatedI have code that has the user select a viewport. I then need to set the selected viewport to an existing view, but I cannot find any exampes of this.
I have the viewport, but how do I get the ViewPortTable/ViewPortTableRecord from it?
Do I need to set the view in the ViewPortTableRecord od the ViewTableRecord?
No problems to this point...
'Code snipIf acPrmpt_res.Status = PromptStatus.OK Then
Dim acVPort As Viewport = Nothing
Dim acViewTbl As ViewTable
Dim acViewTblrec As ViewTableRecord
[Code] ........
I am trrying to rotate the view that I have in my viewport. I used to use a command that had the options Alingn, rotate etc but in this moment I do not remember that command. I you do not remember either
View 6 Replies View RelatedWhen I use the SSM and use the "Place on Sheet" command to create the Viewport from the MS View DWG file, it comes in only as a rectangular Viewport. I tried to see if there's a way to draw a Polyline and select it as a MS View but I don't think that's possible.
Any way to do this without breaking the link between the View DWG and the Sheet DWG?
I need to rotate a view through a viewport in paperspace and tried to use the mvsetup command but LT doesn't recognize that command. How I can do it?
View 5 Replies View RelatedSo I have set camera view in my viewport for a perspective view. This goes okay but when i close my drawing and open it again.The view was changed. I have tried locking my VP, set UCSFOLLOW to 0, display locked=YES as stated on other VP problems in threads. What setting am i missing?
View 2 Replies View RelatedI would like to find out if it is possible to produce a drawing with more than one view frame plotted on a single sheet/layout. I was thinking of minimizing on the number of sheets used for Linear features.
View 2 Replies View RelatedI've got a view layout for 1/8" scale floor plan. I've got 2 gang toilets that I'm trying to use the Callout tool to generate enlarged plans on a different view file.
I'm attempting to send both model views that the Callout tool would produce to a different existing view file.
Have not succeeded yet, and just throwing out the question if it can be done? Or if model views called out have to be in individual files? Don't want to waste my time if it can't be done.
When using "Create Multiple Section Views", some of the information is placed outside the viewport.
How can i get this information inside ?
How do you clean up areas where the section view is outside the viewport limits. C3d should have moved the top section to the next sheet becuase it didn't fit. How do you tell it this? An automatic toggle somewhere?
View 4 Replies View RelatedWe have a number of drawings, where the views in paperspace viewports are not orthogonal to the XY plane. Is there any way that we can adjust the viewport view to a TOP view (a view aligned to the XY plane) without changing the viewport scale?
If I activate the viewport and use either PLAN or View->TOP my viewport scale is destroyed, and the view is rotated along the Z-axis.
So I've created this wall section and used viewbreaks to break the crop regios up so i can fit the final view on a sheet.The problem is, when I place the broken up section on a sheet, the viewport does not break up like the view region.
How do i break up the viewport on the sheet so I can squeeze the visable regions together?
I've struggled with the old issue of shifting images in rotated viewports. We use georeferenced aerial photography by way of these images inserted into their own drawing and then Xreffed into another drawing for printing. The issue is, the image appears shifted in some viewports. Most of the time it prints fine but not always. I searched the discussion groups and found a post a few years ago that a reply user stumbled across a quasi workaround. When the view command's Perspective is turned on and then off within the viewport, the image appears to be locked in it's correct position, not shifted. I have successfully used this procedure several times over the years until now. I have half a dozen drawings that when I turn the Perspective on and then off in a viewport, the image will not display. The xref is loaded and the layer is turned on in the viewport but the image doesn't show. What is the perspective portion of the view command within a viewport?
View 2 Replies View RelatedJust switforeveched to AutoCAD 2013 from 2011. I kept the classic interface as I did since forever. This is the problem I am having now. After I created a viewport in a layout, I right click on the viewport border fully expecting a menu to come up so I can set the type to be 2d hidden. But nothing like that occurs. The help menu came up. How do I get the viewport menu to set the view type?
View 2 Replies View RelatedI have a site survey that I am having rotation issues with.
In the model space the drawing is rotated so when I draw a vertical line it points up (which is what I am used to). However in the paper space, the drawing is automatically rotated so that north is now pointing up, and if I attempt to draw a normal vertical line as i did in the model space the line now points NE.
How can I rotate the view of the viewport in paper space so that my lines as vertical and horizontal. This would not be such an issue if it was just a plan, but I have drawn sections that just look ridiculous.
I remember seeing an article or web cast on how to create a style to display a single line for a manhole. It may have been about using the parts create tool. But for the life of me, I can’t remember where I saw it.
Also I had created a style in C3D2007 to display the pipes in profile as a single line. This was done by drawing the flow arrow in a non printable colour over the top of the pipe.In C3D2008 this is no longer possible. So now what?
I am working on a rendering on vanilla AutoCad 2013, and I am getting frustrated with having to reset my viewport to the named view every time I move my camera.
I know that when you create a viewport you can call up a named view, but is there any way to link it permanently?
Since I installed autocad architecture 2012 I have this problem. When I drag a view from the project navigator in a sheet I see the content and the option to set a scale. So far so good. When I click in the sheet to set the location the viewport goes empty. I can stretch the viewport to top left to get the drawing within range and then move it back to where I want to place the drawing.
View 5 Replies View RelatedWhen I pick rendered for my shadeplot on a viewport, none of the materials applied to multi-view blocks show up. Is this common or is there a fix?
View 3 Replies View RelatedA problem we are having in our office on 1 computer is that this message appears in the command line
'viewport is view locked switching to paper space'
It happens whenever we zoom or pan into one of our locked viewports. We have purposefully locked the viewport so we don't lose the scale when we zoom or pan and want to leave it this way, however, whenever we zoom or pan this message appears and it takes 30 seconds before the screen readjusts to the zoom or pan we require.
I'm in the process of creating an exploded view of an assembly. I'm having to do this in a presentation file, and I was wondering if it was possible to section one of the parts in the exploded view. To be more specific, I have the majority of my parts spread out around another assembly in the center of the page. I want to get a three quarter section view of the center assembly so the internals are visible. Is this possble from within a presentation file and if so, how can it be done?
Inventor Professional 2013
Intel Xeon W3680 @ 3.33Ghz
12GB DDR3 RAM
NVIDIA Quadro 2000 GPU
Windows 7 Professinal 64-bit
I have had this issue for about two weeks. I am not aware of any changes to my system though Windows 7 updates automatically.
Often, but not all the time, when I am in a floating viewport which is locked and I zoom in, the part of the drawing disappears as if the view on the viewport has adjusted to one side so that I cannot see any of what I am working on. If I escape the command and 'undo' last command it takes me back to the correct view but in paperspace.
This is a pain as I cannot zoom in to locate a point accurately. It only happens when I zoom in quite close. The viewports are locked and it is only a problem recently. I have used CAD for 20 years and LT 2008 for the last 4-5 years so I dont think it is a user issue. Maybe a settings issue or bug, but I have not knowingly changed any settings which would do this and cannot see why this would be a 'feature'.
What I am attempting to do is: add text, some dims., and some info. to a viewport i have added to a drawing for my field guys. I am a sheet metal worker and have produced a drawing of duct work. one viewport is a plan view, one is a swiso, and another is a left-elevation view. everything is good except the left-elevation view which I would like to add details to. I am assuming I need to change the ucs so that i can place lines, dims and text and get them to show up without them snapping to 0 z.
View 9 Replies View Related