Sometimes when I am dimensioning an object, my autosnap will pick up the end of an adjacent dimension extension line instead of the end of the object. Is there a way to prevent that?
View 4 RepliesWhen placing a dimension with the text outside of the extension lines, it defaults to placing the text either above right or below left of the arrows. If you try to grip/drag the text to another location (i.e. below right or above left) it won't allow it. I don't know if it is following some standard, but in the example shown, I had to explode the dimension to position the text in the preferred location.
View 3 Replies View RelatedHaving used another CAD program for several years, I was used to the idea that all radius dimensions, like of a given arc, would easily start at the center of the arc, thereby denoting the position of the arc's center.
I'm slightly bugged with some CAD users, even books on the subject by autocad users, that give an arc's dimension from the outside of the arc, yet fail to show the location of the arc's center when it may not be self explanatory. Not good dimensioning practice from what little I've been schooled...
So, in AutoCAD 2007, how do I get an arc's radius dimension line to start at the center and point out to the edge. I can do all kinds of things to the position of the text, etc, but can't figure how to get it to start at the center. (The dimension line needs to start at the center.)
Some times when I re open a drawing I have been working on, I start to dimension and I notice that the dimension extension lines stay the same length when I move the dimension in and out from the object being dimensioned.
Not sure why this happens, I do all my dimensions in model space, in fact I do just about everything in model and then just set it up in paper space to print.
I never change anything when I start a new drawing in my template, so not sure why it happens.
I'm using Inventor 2011 and I can't figure out how to set my dimension settings so it breaks the dimension extension lines automatically when crossing over other dimension extension lines. I saw that others say it just happens, but it is not "just happening" for me. how to set my dimensions so when dimension lines cross each other one of them automatically breaks?
View 9 Replies View RelatedIs there a way to do a jog in a dimension line extention?
(Colossians 3:23-25)
see attached jpg. I want to know if there is a way to get rid of the "extension line" that the diameter dimension creates?
as you can see it runs over the slots on my detail and looks confusing.
win 7 64 bit sp1
cpu intel xeon E5-2687W0@3.106
eight core
two solid state hard drives
32 gig of ram
Autodesk product design
suite premuim 2014 64bit
Nvida quadro 4000
Space Pilot ver. 1.6.2 2010
slphantom (NNTP handle: scottl)
When you make a diameter or radius dimension it always has this static extension line shown in red when you move the dimension far enough away. I can not seem to extend this extension line at all it is always the same length no matter what variable I change. How to lengthen this extension line?
View 9 Replies View RelatedIt's 2012. I haven't found a setting in the dim style or the RMB options to turn off the extension line. I saw the posts showing drawing a sketch in the view but come on, all that to just turn off the line?
IV 2012 all sp & fixes
I'm inserting dimensions and the tics keep coming out huge and not on the dimension line, in fact there's one on either side 20 ft out. If I change the drawing scale in the tab at a the bottom the tics get smaller and closer in, but they are still off the dimension string by a long shot.
View 3 Replies View RelatedHow do I get the extension lines to be annotative?
View 7 Replies View RelatedI want to use diameter extension lines to span the diameter of the circle by forcing the dimension line to be on. When I do that, the arrows are on the outside of the diameter and I want them on the inside so I use the flip arrow command. What happens is the extension line opposite of the dimension text is sticking outside the circle and I want to get rid of it because it just looks bad. I dont see a way of turning off this little extension line. Every thing I turn off doesnt seem to do anything.
View 7 Replies View RelatedHaving problem of polar tracking extension lines working in one direction, but not perpendicular to that orientation? For example, when drawing a simple rectangle after drawing (2) sides, If I go to snap to my initial starting point to show a vertical extension line to intersect with my third line I am drawing, the vertical extension will not show up, even though the horizontal extension line is visible, and even though it snaps to the my starting point to where I wish have the polar tracking show the vertical extension.
View 9 Replies View RelatedI have programs that at some point or another create dimensions for what was drawn. When you have a vertical dimension that doesn't fit between the extension lines, it will either go up and to the right or down and to the left.
I can change it manually by selecting the dimension and then right click and pick Dim Text position > Move with leader.
What I want to know is, is there a way to set the vertical dimension where you want it programatically? I would like to put the vertical dimension down and to the right of the arrows if possible.
I am using AutoCAD 2011. When I create a radius dimension on the inside of an arc, and I place the dimension beyond the center point of the arc, AutoCAD automatically draws an extension to the arc and points my radius dimension leader to the outside of this extension, rather than to the inside of the original arc.
I don't really like this. I prefer for my demension leader to point to the inside of the original arc. I can get exactly what I want by going into "Properties" for the radius dimension and turning the "Ext Line" property off.
Rather than having to do this every time, I'd like to create a dimension style that would give me this functionality all of the time. When I try to modify my dimension style, I see that there are just two parameters for Suppress Ext Line 1 and Suppress Ext Line 2. These seem to apply to both linear dimensions and radial dimensions. Is there anything I can do to suppress the extension line for radial dimensions only and not linear dimensions?
Sometimes when I plot/publish a DWF or PDF the arrows extend past the extension lines. I need the point of my arrows always end at the extension line?
View 1 Replies View RelatedI am having an issue with my dimensions. If I have a dimension that is 1'-3" or larger, my extension line beyond my dimension line extends the normal length, but as soon as my dimension goes under 1'-3", the extension line then gets twice as long outside of the dimension line (see attachment). I have researched...and i can't seem to find a dim variable that will let me change this. is there anything to control this happening once my dimension goes below 1'-3"?
View 1 Replies View RelatedI am using AutoCAD Civil 3D 2012
The marker box that usually shows when you want to snap to an object is not appearing. What do I need to try to get it to show up again?
I have a point cloud that i want to snap a boundry around its outer limit. Is there some way to do this automaticly? I tried creating a surface and using the maximum triangle length to get a good boundry. For some reason i loose a lot of pionts at the edges with this boundry. I have removed points that represents water so i have a part in the midddle that i want a boundry around.
View 3 Replies View RelatedMy autosnap marker is not working in AutoCAD 2010 Mechanical. My settings in below.
View 8 Replies View RelatedI am experiencing a problem where my Autosnap Settings (system variable "autosnap") are not be saved in my Civil 3D session. When I open Civil 3D 09 (SP1), my autosnap variable gets set to some weird number (aka 6768 or -12566). Each time I get into the drawing I need to reset this to 55, or go into my Options-Drafting-Autosnap Settings and toggle on Marker, Magnet, and Display Autosnap tooltip. This is a system variable and should be retained upon entering a drawing file.
View 7 Replies View RelatedIs there any way to dimension a bent lines?i would like to be able to have just one total dimension of these two lines instead of measuring each line.in my type of work it is not necessary to show dimension of each segment, but would be nice to at least show a total dimension instead.
View 3 Replies View RelatedI moved from acad 2000 to 2009. My crosshair hesitates over every dimension line. Also almost impossible to use grips on the dimension lines. Anyway to turn this off?
View 9 Replies View RelatedIs it possible for AutoCAD to notify you if you have overlapping dimensions.
See sample.
DRAWINGS.dwg
I have made thousands of sheet metal parts and their associated drawings without issue but this time, I made a part and attempted to make a drawing but dimension lines won't attach to certain geometry in the drawing. It acts like it will until I click the second line for the dimension then it errors, telling me the same error message that comes up when you delete a feature that previously had a dimension.
I also can't place an origin for doing a hole chart, for example. It just turns purple and says it isn't attached even though it clearly is.
I have a problem with Inventor 2013. The dimension lines have disappeared. I've been through all the dimension styles and layers to make sure I hadn't turned one off
All other drawings are fine and if I create another even using the same model it works just fine but I'd rather find out why than re-do the whole drawing.
when I draw a shape and add a dimension to it, the text and the numerical and the arrows of the dimension are small, so I have to increase the text height manually
how can I make it automatically scale itself?
also similiar thing with the lines, I tried putting a dashed center line on a shape, it looks solid but when I zoom it it does not.
how can I solve this?
I have a template IDW that i use for bearings. When I opened it today I noticed that two of the dimension lines were missing. The dimension and arrows are there. I tried deleting them are recreating them with the same result.
The interesting thing is, when I created the dim above the part it was fine, when I dragged it below the part the lines went away. After that no matter were I moved it the lines would not reappear.
I installed SP1 a while ago and just now installed the update to SP1 (DL20857064.zip). It did not fix the problem.
Is it possible to hide the dimension lines like in the attached picture?
Autodesk Inventor 2012
We resently upgraded to Inventor 2013 and since then we have been having an issue of dimension and leader lines being hidden under a text box or some other drawing entity.
This is very confusing since the text box does not have a white out associated with it, nore is there a way to put the test box to the back and dimension lines to the front...
It seems like our puppet masters that program this amassing tool where up to something and didn't quite get there.
IT sure would be nice (or an absolute requirement) that this gets fixed so I don't have to learn new hoops to jump through to get a quality drawing out of Inventor.
How can I print a dimension with its arrows but without it's dimension lines?
For example--I draw a rectangle and draw a horizontal dimension across the center of the rectangal. Then I flip the arrows and drag the number to the left outside of the rectangal. I want arrows facing inward from the left and right and the number out to the left. I don't want a line stretched across the center of the rectangal.