When you make a diameter or radius dimension it always has this static extension line shown in red when you move the dimension far enough away. I can not seem to extend this extension line at all it is always the same length no matter what variable I change. How to lengthen this extension line?
View 9 Repliessee attached jpg. I want to know if there is a way to get rid of the "extension line" that the diameter dimension creates?
as you can see it runs over the slots on my detail and looks confusing.
win 7 64 bit sp1
cpu intel xeon E5-2687W0@3.106
eight core
two solid state hard drives
32 gig of ram
Autodesk product design
suite premuim 2014 64bit
Nvida quadro 4000
Space Pilot ver. 1.6.2 2010
slphantom (NNTP handle: scottl)
It's 2012. I haven't found a setting in the dim style or the RMB options to turn off the extension line. I saw the posts showing drawing a sketch in the view but come on, all that to just turn off the line?
IV 2012 all sp & fixes
how to make a radius dimension a diameter dimension? I have Inventor Profession 2013.
View 1 Replies View RelatedI am trying to edit my drawing template dimension style to always do a diameter (if it is a circle). Right now it defaults to radius and I manually right click and change it. I found all sorts of styles for how it displays the radius and diameter, but didn't find where to set the default.
View 7 Replies View RelatedWhen I dimension an arc to find the radius, the dimesnions appears as a line going from teh center of the arc to the edge of the arc with the dimension in the middle. I don't want this. I want a leader pointing to the R text and that's it.
I've attached a photo of both scenarios- one dimension is the style I don't want, and one is basically the style I want (I'd like it to be more of an elbowed leader line), but it only appears when I use AutoCAD's ISO25 dimension style.
How do I change this dimension into a diameter dimension?
I have tried editing the dimension style to display as a diameter and it doesn't change it. I tried creating a new dimension style and it doesn't change it.
Having used another CAD program for several years, I was used to the idea that all radius dimensions, like of a given arc, would easily start at the center of the arc, thereby denoting the position of the arc's center.
I'm slightly bugged with some CAD users, even books on the subject by autocad users, that give an arc's dimension from the outside of the arc, yet fail to show the location of the arc's center when it may not be self explanatory. Not good dimensioning practice from what little I've been schooled...
So, in AutoCAD 2007, how do I get an arc's radius dimension line to start at the center and point out to the edge. I can do all kinds of things to the position of the text, etc, but can't figure how to get it to start at the center. (The dimension line needs to start at the center.)
How would you add features like radius, diameter to a leader line?
View 5 Replies View RelatedWhen I use the extend command, only the selected line segment extending to the current line segment but can not be extended to the extension of his line, where is the setting not right? Another computer I will be able to extend the line to the extension part.
View 2 Replies View RelatedMy radius and diameter dimensions keep jumping from my original line to another, see attached
View 1 Replies View RelatedI am having an issue with my dimensions. If I have a dimension that is 1'-3" or larger, my extension line beyond my dimension line extends the normal length, but as soon as my dimension goes under 1'-3", the extension line then gets twice as long outside of the dimension line (see attachment). I have researched...and i can't seem to find a dim variable that will let me change this. is there anything to control this happening once my dimension goes below 1'-3"?
View 1 Replies View RelatedI am trying to create a dimension in an .idw that goes from a line to the tangent of the outer diameter. I have tried several approaches but I cannot get it to work. Essentially I am trying to replicate a drawing which was created in Solidworks but I am having trouble with this dimension.
View 4 Replies View RelatedIs there a way to do a jog in a dimension line extention?
(Colossians 3:23-25)
How to convert the single line below containing 42" radius curves to a solid 4" diameter cylinder/pipe?
Capture.jpg
Is there a way to make the linear dimension a diameter dimension?
View 9 Replies View RelatedI want to use diameter extension lines to span the diameter of the circle by forcing the dimension line to be on. When I do that, the arrows are on the outside of the diameter and I want them on the inside so I use the flip arrow command. What happens is the extension line opposite of the dimension text is sticking outside the circle and I want to get rid of it because it just looks bad. I dont see a way of turning off this little extension line. Every thing I turn off doesnt seem to do anything.
View 7 Replies View RelatedSometimes when I plot/publish a DWF or PDF the arrows extend past the extension lines. I need the point of my arrows always end at the extension line?
View 1 Replies View RelatedMy company is trying to Standardize all drawings produced to 1 format. the one we are attempting to create would be in the form of: nominal upper limit^lower limit. this is easily acheived in autocad and linear, chamfer, and hole/thread dimensions in inventor. but radii's and diameters from a round surface (as apposed to linear diameters) we have run into a snag with. We cannot seem to find a way to either remove the prefix symbols or be able to insert text between the symbol and tolerance.
below is a illistration of the problem and the form of the new dimensions.
I made a small plant and to create pipes i used cylinders, now I need to create a material list and for this I need to extract the radius(diameter) and height for each cylinder, but i don't know how. I am having lot's of cylinders (2000 elemets). I put also a sample here.
View 4 Replies View RelatedHow do I make Diameter and radius symbols when annotating?
View 2 Replies View RelatedThe default format for a radius and diameter dimension is inserted with a prefix "R" and diameter symbol ahead of the measured dimension. Our company standard pre-Inventor was to place either "RAD" or "DIA" after the measured dimension. We can not seem to find anywhere in the setup to change how these type dimensions are inserted as a default or custom setting.
Can we change/customize the radius and diameter dimension formatting?
Inventor 2014 Ultimate
Windows 8 Pro
It is not possible forme to add the fil because it is to large 1.8MB how can I poste then I like to know if it is possible to extend the button flat surface diameter ø12.5 up to the shaped surface. The result should be a total solid block whit a surface shaped hole.
File last up-date with Autodesk Inventor Professional 2013
how to break diameter line into horizontal line at the end ?... there's no such option in editor style (I want to have 2 arrows for this diameter, not one as it is in editor options)
View 2 Replies View RelatedWe have been having an issue with this for a long time in hopes of it being fixed in any new release. If I click Diameter and pull it to the OD of hte circle it shows as in the picture which is what we want. If I pull it to the ID it pulls straight from that point and the dimension is not level.
The only way we can fix it is click on it, go to properties, scroll down to text, and in the text rotation box, type 90.1 and hit enter.
Is there if fix for this issue?
We need re-location the diameter dimension after we change the drawing view's scale. but we didn't know how to change the Startpoint of the dimension (mark with Red word "1"), just find the text location.
Who knows how to set the new point to for the startpoint?
I have been able to dimension any circle on the drawing， but if there're several circles with the same radius ,I just don't know how to dimension the circles with the same radius with only one dimension.
View 1 Replies View RelatedIm drawing the image below for school but I cannot figure out how to create the radius dimensions as they shown.
The only ones I know how to do are they .25 and the .75 diameter. I have tried changing the dimension style in every way I can think of. Just to clarify the 1.31 and .63 radius demotion how the leader starts in the center and the arrow is on the inside of the circle yet the text has the extended leader and is outside the circle and the other radius demotions the text is in the middle of the leader is what I am trying to learn to do.
The standard in the industry I work in is the radius dimension goes on the inside of the arc. However, AutoCAD defaults the dimension to the outside of the arc. Is there a way to make it default to the inside? If not then this is the issue when I use the mirror command.
Attachment 44015
That arc appears and I cannot get rid of it.
I am new to AutoCad, and I'm sure this is a simple question. How do I put radius dimension in fraction format?
View 4 Replies View RelatedSometimes when I am dimensioning an object, my autosnap will pick up the end of an adjacent dimension extension line instead of the end of the object. Is there a way to prevent that?
View 4 Replies View Related