When I use the extend command, only the selected line segment extending to the current line segment but can not be extended to the extension of his line, where is the setting not right? Another computer I will be able to extend the line to the extension part.
View 2 RepliesWhen you make a diameter or radius dimension it always has this static extension line shown in red when you move the dimension far enough away. I can not seem to extend this extension line at all it is always the same length no matter what variable I change. How to lengthen this extension line?
View 9 Replies View RelatedI am having an issue with my dimensions. If I have a dimension that is 1'-3" or larger, my extension line beyond my dimension line extends the normal length, but as soon as my dimension goes under 1'-3", the extension line then gets twice as long outside of the dimension line (see attachment). I have researched...and i can't seem to find a dim variable that will let me change this. is there anything to control this happening once my dimension goes below 1'-3"?
View 1 Replies View RelatedHow do I extend a line to a block or trim? seems like every time i trim or extend the line to a block the line won't recognized/notice the block. what can i do?
View 1 Replies View RelatedEverything is on one layout/sheet.
Currently there are a total of 3 viewports in an L formation. The fourth viewport, will go in the upper right. But first, I have to get these aligned.
I think the viewports themselves are fine enough. The problems arise because the model is in Model space so, construction line (as far as I can tell) didn't want to snap to a line, (on the model,) in Paper space.(vertical or horizontal) So, I can only see the construction line, in one viewport at a time. Which means, the construction line is not visible in the viewport immediately to the left. So, I can't extend the construction line across both viewports, to to snap them to the construction line.
I had thought this would work with no problem. I know the elevation I need to start an arc at and an elevation at a point along the arc. I drew that portion of the arc and then extended the arc to a line where I need the arc to end. I had expected the arc to extend along it's current grade the way a straight Feature line would. But the end dropped to 0.
I undid the extension, listed the FL arc to get the grade, extended it again and used the Elevation Editor to set the previous grade. But why didn't the extension work? I checked for other FL in the site that might cause this but there were none.
when drawing a line whether a normal line or polyline it adds an tail to the top going 90 degrees to the right, and even on paper space it still shows them. but I cant click on the or delete them, they move with the line too.
View 9 Replies View RelatedI want to use this pic for my phone wallpaper. I tried to enlarge it but the quality drops really bad. It needs to be 960x800. Is it possible to extend the top part of the picture to make it more "square" without cropping the width?
View 1 Replies View Related I set up our company log which gets embossed on most parts as a sketch block in an .ipt. The .ipt contains nothing but the sketch block. To use it, the designer only needs to derive the Logo.ipt file into their part and then use the scale setting to set the derived block to the desired size for that part. The result is a scalable set of line geometry that can easily be used for extrusion or emboss that is standard for all users. It works beautifully, that is until you try to use it in a sheet metal part in 2012.
For some reason, when this same part, which works perfectly in normal parts, is derived into a sheet metal part an error pops up stating that, "Selected part does not have any geometry that can be derived." Say what?
I was able to find a workaround by directly copying the block into the sheet metal part, but you no longer have the ability to go back and scale it if needed. Even more strange, when the block was copied over, it could not be deleted from the new part.
Is this just a bug with 2012? Why does it work in a normal part but not sheet metal?
Is there a way to do a jog in a dimension line extention?
(Colossians 3:23-25)
I have a mac with autodesk 2014 on it. I am trying to import a step file but after I select what to import nothing happens.
View 4 Replies View RelatedI have created the part based on piece of standard angle taken from library. Now I want to make a mirrored copy of this part by Component-Mirror.
Inventor does not let me do it with standard part.
The question is: How I can transform a standard part to normal one, I mean I could get rid of belonging to standard part? Making a copy does not work. The only way is to derive and mirror this part but I wish there could be easy way.
see attached jpg. I want to know if there is a way to get rid of the "extension line" that the diameter dimension creates?
as you can see it runs over the slots on my detail and looks confusing.
win 7 64 bit sp1
cpu intel xeon E5-2687W0@3.106
eight core
two solid state hard drives
32 gig of ram
Autodesk product design
suite premuim 2014 64bit
Nvida quadro 4000
Space Pilot ver. 1.6.2 2010
slphantom (NNTP handle: scottl)
We are working on a road widening scheme where one edge of the road is retained as far as possible while other edge being widened. I like to design a retained channel line by extending the cross fall between the existing center line and the exiting channel line on to the design one.
It is possible in civil 3d to extend the gradient between two feature lines at some offset from reference feature line?
[URL]....SAYS:
“Adjust the length or angle of straight segments
1. With the Direct Selection tool, select an anchor point on the segment you want to adjust.
2. Drag the anchor point to the desired position. Shift-drag to constrain the adjustment to multiples of 45°.”
Question: How do I proceed if I’d like to extend a line on one side by its endpoint, while I want to keep its original angle instead of 45° degrees?
And: assuming we’re not working with a standing-alone line, but as part of a construction, as you can see on the screenshot. The point should be move to the intersection on both lines (green and turquois).
I thought, maybe working with functions in GRAPHER – but I hope there is an easier way directly in ILLUSTRATOR.
Is there a way to remove the extension line from a leader (when using the Leader Text command)? I'm trying to end up with just text, an arrowhead, & a straight line. It would look like this:
<---------- TEXT
as opposed to:
TEXT
/
<----------/
(Is that the best diagram ever, or what?)
The "extension" line on my "autotracker" has gone from being in front of my tool tip (where I'm headed) to following my tip (where I've been)
View 5 Replies View RelatedI've been using a very old version of Photoshop for the last 10 years and I'm used to using the shift key to extend a line or paint stroke. By that I mean, I use the paint tool to make a dot and then hold down the shift key and make another dot elsewhere and that creates a straight line. I just purchased CS6 and that function doesn't seem to be happening. Is this something I need to activate in a preference?
View 10 Replies View RelatedIt's 2012. I haven't found a setting in the dim style or the RMB options to turn off the extension line. I saw the posts showing drawing a sketch in the view but come on, all that to just turn off the line?
IV 2012 all sp & fixes
I have made a Family that is based off the Metric Structural Framing - Beams and Braces template. When I import my Family into a project and create a instance of the Family (which is a channel) the channel doesn't extend the whole distance of the geometric line. Its always 1500mm long (thats the default length in the .rfa file). See below image for my problem:
I made my extrusion inside the Left Elevation view and not inside a Floor Plan view; simply because it is easier to create the complex geometry of it. Maybe this has affected its inability to stretch to the length of the line? How can I edit my family so that the extrusion will stretch the whole length of the line/beam?
How do I extend a horizontal line like such... _________ outwards from both directions left and right simultaniously, basically giving the effect that it is growing longer from both ends out, like such ______________________________. ( and still looking very clean and as the same line, as it extends )
View 2 Replies View RelatedI'm trying to load an ink splatter brush set from brusheezy.
The extension is *.abr
When I select load brushes and pick the file nothing happens. I'm not asked to replace or append and my brush palette remains the same.
Any ideas on what the problem may be?
Had to reload elements 7 after disk crash. Restored from backups. Unable to view or edit files with extension cr2
View 1 Replies View RelatedHow can I draw a straight line without that protractor shaped dotted line following my cursor making it lag and also not snap correctly to the next line? Also, I have noticed that I can't set my user interface to auto cad classic settings. There seems to be no option for it in workspace settings.
View 3 Replies View RelatedSometimes when I plot/publish a DWF or PDF the arrows extend past the extension lines. I need the point of my arrows always end at the extension line?
View 1 Replies View RelatedI am working with vector art that has lines that either look like they were cut off and not finished out or extend to the edge of the page so they are straight when they should actually be curved.
Is there any way to take a straight line or part of an image and curve it with ease or will I have to redraw or alter each line?
I'm learning how to create extension (flex - extension builder) for Illustrator and how to make it communicate with a plugin.
The samples provided in the SDK detailed how to load /unload extension from a menu item from Illustrator, and how to add / remove EventListeners to make the magic happen.
to sum up, this is something like that:
1- click on the menu item
2- load extension
3- add listeners
4- do your stuff......
5- remove listeners
6- unload extension
Basically my plugin is a module/service which is in charge of dealing with / modifying artwork tree. It has no User Interface.
My extension will have a user of this service.
What I would like to do is to load my extension as soon as my plugin is loaded, and unload the extension when the plugin will be unloaded.
Or notify when extension is loaded or unloaded.
Is that possible and hw could I achieve that?
I found out that you can't change line color in the line nova because a fix to prevent white on white or something like that. Is there another way to change the line color.
View 6 Replies View RelatedI'm using Inventor 2011 and I can't figure out how to set my dimension settings so it breaks the dimension extension lines automatically when crossing over other dimension extension lines. I saw that others say it just happens, but it is not "just happening" for me. how to set my dimensions so when dimension lines cross each other one of them automatically breaks?
View 9 Replies View Relatedmake flat patern for this part. for screw.
View 1 Replies View RelatedWhen I double click a part in an assembly it does not edit the part.
When I right click "edit" is greyed out.
How do I edit a part in an assembly.