when drawing a line whether a normal line or polyline it adds an tail to the top going 90 degrees to the right, and even on paper space it still shows them. but I cant click on the or delete them, they move with the line too.
View 9 RepliesI am having an issue with my dimensions. If I have a dimension that is 1'-3" or larger, my extension line beyond my dimension line extends the normal length, but as soon as my dimension goes under 1'-3", the extension line then gets twice as long outside of the dimension line (see attachment). I have researched...and i can't seem to find a dim variable that will let me change this. is there anything to control this happening once my dimension goes below 1'-3"?
View 1 Replies View RelatedIs there a way to do a jog in a dimension line extention?
(Colossians 3:23-25)
see attached jpg. I want to know if there is a way to get rid of the "extension line" that the diameter dimension creates?
as you can see it runs over the slots on my detail and looks confusing.
win 7 64 bit sp1
cpu intel xeon E5-2687W0@3.106
eight core
two solid state hard drives
32 gig of ram
Autodesk product design
suite premuim 2014 64bit
Nvida quadro 4000
Space Pilot ver. 1.6.2 2010
slphantom (NNTP handle: scottl)
We are working on a road widening scheme where one edge of the road is retained as far as possible while other edge being widened. I like to design a retained channel line by extending the cross fall between the existing center line and the exiting channel line on to the design one.
It is possible in civil 3d to extend the gradient between two feature lines at some offset from reference feature line?
When I use the extend command, only the selected line segment extending to the current line segment but can not be extended to the extension of his line, where is the setting not right? Another computer I will be able to extend the line to the extension part.
View 2 Replies View RelatedIs there a way to remove the extension line from a leader (when using the Leader Text command)? I'm trying to end up with just text, an arrowhead, & a straight line. It would look like this:
<---------- TEXT
as opposed to:
TEXT
/
<----------/
(Is that the best diagram ever, or what?)
The "extension" line on my "autotracker" has gone from being in front of my tool tip (where I'm headed) to following my tip (where I've been)
View 5 Replies View RelatedWhen you make a diameter or radius dimension it always has this static extension line shown in red when you move the dimension far enough away. I can not seem to extend this extension line at all it is always the same length no matter what variable I change. How to lengthen this extension line?
View 9 Replies View RelatedIt's 2012. I haven't found a setting in the dim style or the RMB options to turn off the extension line. I saw the posts showing drawing a sketch in the view but come on, all that to just turn off the line?
IV 2012 all sp & fixes
Sometimes when I plot/publish a DWF or PDF the arrows extend past the extension lines. I need the point of my arrows always end at the extension line?
View 1 Replies View Relatedangle.jpg
How can I draw the bottom line, with an angle of 132 relative to the middle line?
I have to draw a rather weird drawing with a lot of angled lines. Currently I'm using UCS to draw them but it's really tiresome.
I would draw 1 line, then type in UCS, select the X and Y axis, draw that line, escape, then hit in UCS again, rinse and repeat.
Is there a simpler way? I tried polar tracking "relative to last segment" but it still uses the x axis as the base, which is not what I want. I want the line to be the X axis.
I'm learning how to create extension (flex - extension builder) for Illustrator and how to make it communicate with a plugin.
The samples provided in the SDK detailed how to load /unload extension from a menu item from Illustrator, and how to add / remove EventListeners to make the magic happen.
to sum up, this is something like that:
1- click on the menu item
2- load extension
3- add listeners
4- do your stuff......
5- remove listeners
6- unload extension
Basically my plugin is a module/service which is in charge of dealing with / modifying artwork tree. It has no User Interface.
My extension will have a user of this service.
What I would like to do is to load my extension as soon as my plugin is loaded, and unload the extension when the plugin will be unloaded.
Or notify when extension is loaded or unloaded.
Is that possible and hw could I achieve that?
I'm using Inventor 2011 and I can't figure out how to set my dimension settings so it breaks the dimension extension lines automatically when crossing over other dimension extension lines. I saw that others say it just happens, but it is not "just happening" for me. how to set my dimensions so when dimension lines cross each other one of them automatically breaks?
View 9 Replies View RelatedI am trying to draw a line. Now all of a sudden, there is a stupid arrow. how to do i turn this annoying freature off?
As well, I want to draw multiple lines on one layer, however everytime I draw a line, i get a new layer!
I'm trying to use the line tool to draw a colored line, I draw the line via Line tool, it appears in grey, I right click>stroke path and select Pencil > OK, the line is still grey and not the foreground color. If I do the same with a Rectangle Tool, it works fine and darws me a nice colored rectangle. What am I doing wrong? This is driving me nuts...!!
View 1 Replies View RelatedI'm in auto cad 2009 and when i am trying to draw a vertical line it is only drawing horizantal while the ortho mode in on.
View 6 Replies View RelatedFirst off I'm using AutoCAD 2008 and I'm trying to input survey points to establish a subdivision.
My units are set as follow: length type: decimal with precision set at: 0.00. Angle type: Surveyor's Units with precision set at: N 0d00'00" E. Units to scale inserted content: feet.
I have a specific point at which i want to start from and that is 1421334.93,78320.62 which is my benchmark. I want to start my next point at 113.66 feet away from this benchmark at a bearing of N 5d27'23" W. So far I have tried using the command @113.66<N5d27'23"W but nothing happens.
I have a particular drawing that every time i try and draw a line or a pline, it only draws in magenta. And i have to go into my properties dialog box to set it by layer and not by color....Is there some setting in the drawing taht is making this happen?
View 2 Replies View RelatedI have a line which is at (0,0) and (2,2). I need to draw a perpendicular to this line from point(1,0).
View 6 Replies View RelatedRecently I've been working with a lot more projects that contain curved architectural features. It appears that I am unable to draw a line to an implied perpendicular point on an arc. I can draw a line to an implied point perpendicular to another line but not an arc. refer to attached images.
Image1 demonstrates the implied point perpendicular to a line.
Image2 demonstrates that there is no implied perpendiuclar point on the arc given by AutoCAD.
Image3 demonstrates that if the arc is manually extended, a point perpendicular to the arc does exist.
It seems like this should work.
Image1
Image2
Image3
Why is that box appear whenever i draw a line? Does it gona affect the printing? how can i make it disappear?
View 3 Replies View RelatedWhat would be the easiest way to create a 3-dash line for a drawing?
I have a user with a need for a 3-dash line. Like a phantom line but with 3 dashes.
I know how to edit the pen-up, pen-down settings in a .lin file. But then what would be the best way to handle the new line when it is sent to the client? Would I need to create a custom line file and sent it with the .dwg files or could I edit the acad.lin file? Would the receiver run into problems with missing linetypes?
I am now using AutoCAD 2007 and I am a new AutoCAD user. How can I draw a vector or a line with one or two arrow ends in AutoCAD ? It is really simple to do that in MS Word
View 9 Replies View RelatedI use Cad2013 . During a line command , I can not see the length beside the courser , so I have enter the length using keyboard and it is very time consuming .
I do not remember if I changed any default settings but It used to work properly .
Win 7-32 bit - cad2013 full version - no plugins - No viruses .
How do I to set and to see or show the existing grips point when drawing new line?
View 8 Replies View RelatedI am running AutoCAD 2012 and i am having a problems with drawing a line.The problem i have with it, i have changed some settings and i can't remember what i changed. But how to change it back.
First let me explain what i am talking about. Once i am in front view and trying to drawing a line vertical and with ortho on, it will not allow me to draw a line vertically either up or down, only horiztonal. It looks like to me that ortho is lock on top ortho only.
I have a basic drawing with dimensions A, B, C, D & E. Can those dimensions be tabulated in such a way that they can be altered within the table so that the drawing redefines itself in line with the new dimensions?
View 3 Replies View Related VB.NET with VS2010, Inventor 2012
I have a drawing view of a part with a sketch that contains some lines. I need to pick one of the sketch lines.
I can pick a line with sketch active using the kSketchCurveLinearFilter
I have not been able to pick it from outside of sketch. Have tried using kDrawingCurveSegmentFilter to get a DrawingCurveSegment but I can not get the sketch line from the DrawingCurveSegment
I assume there is a way to get the sketch line from DrawingCurveSegment or DrawingCurveObject but have not figured it out.
I am a new user of Autocad LT and looking for drawing a tangent line to a point on a circle.
View 7 Replies View Related