AutoCAD Map 3D :: Pline Segments Perpendicular After Digitizing Buildings
Jan 31, 2012Have a lisp or other addon to make pline segments perpendicular after digitizing buildings.
View 2 Replies
ADVERTISEMENT
AutoCAD Civil 3D :: Perpendicular Line From Point Laying On A Line / Pline
Sep 30, 2013 I have a line or a pline segment and i want to start a line from a point laying there and go perpendicular outwards. Is there a way to do it with tracking?
Yes, i saw the command draw line at an angle but i find it a little bit complicated for a simple task like that. I am sure autodesk have a simplest solution about that.
If i am already at the draw line mode and i can easy catch the tracking perpendicular to previous segment but if i want to start from another line and go perpendicular i cannot make the tracking work.
AutoCAD Visual LISP / AutoLISP :: Convert 2D Pline With OCS Into 3D Pline In WCS
May 29, 2012I have LWPOLYLINEs that represent a cross section of a train tunnel. Each LWPOLYLINE lists its 2D points in an Object Coordinate System.My task is to create 3D Polylines in WorldCoordinateSystem using those LWPOLYLINEs.I have posted a drawing with sample objects.
I have attached a sample drawing. Drawing was created with Civil 3D 2013, but I exporttoautocadr12dxf'd it and then save to 2004 dwg so most should be able to open it.
AutoCad :: Calculate Length Of Line Segments And Arc Segments Separately
Jan 19, 2012I have one LW polyline consisting lines and one or two arcs. I want to calculate length of all line segments and arc segments separately and the resulted values to be shown as attributes (seperate attributes for line segments and arc segments).
View 3 Replies View RelatedAutoCAD 2010 :: Some Indication That Shows Direction Of Digitizing?
Mar 13, 2012Is there some indication that shows the “direction” of the digitizing?
For example, in the screenshot below, how to know the start and the end of the line? Which indication the AutoCAD provides rather than the coordinates?
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
AutoCad :: How To Use 2 Button Cordless Pen Stylus For Digitizing / Tracing Drawings
Jul 14, 2011I have both a 16 button cordless puck and a 2 button cordles pen stylus. I have the 16 button cordess puck configured to AutoCad 2011 tablet0.dwg. I want to be able to use the 2 button cordless pen stylus for digitizing/tracing drawings from model ship kit plans. So, do I calibrate or configure the pen stylus so AutoCad 2011 will recognize it?
View 2 Replies View RelatedPhotoshop :: Shading And Digitizing Sketches ...
Jul 14, 2009How to paint digitally in Photoshop and how to converted drawings digitally and paint them ?b) Tutorial or even a book but a tutorial would be prefered, on coloring and adding shadows to your drawings.
View 8 Replies View RelatedGIMP :: Digitizing / Tracing Image With 2.8 (2012)
Jun 25, 2012I am considering using GIMP 2.8 on my system with Mac OS X 10.6.8 to do thefollowing:
(1) Digitise a photograph by tracing over parts of it with lines. The photocould be, say, the roots of a tree. The lines would be colour codeddepending on the state of what they are over. I.e. roots in one state getstraced with one colour, while roots in another state would get a differentcolour. In the end I might end up with a bunch of lines, with the differentcolours of lines organised in different layers.
(2) Calculate the relative proportion of lines of a certain colour to thetotal length of all lines.
To do the above, I am wondering if GIMP has the ability to calculate thelength of lines drawn over an image (in, say, number of pixels). This way, Ican obtain the total pixel length all lines put together, and the totalpixel length of, say, just the blue lines.
Do you think GIMP is suitable for this kind of image analyses? Or should Iuse a vector based program like Inkscape?
AutoCAD Map 3D :: How To Create 2.5D Buildings
Apr 27, 2012I want to create 2.5D Buildings, like at google maps website.
Example:
How to do it?
Photoshop :: Digitizing Family Photo Album And Its Captions
Apr 2, 2012I use CS4 on the Mac. I'm looking for an efficient solution for digitizing family photo albums. I know how to scan and fix the scanned image, if necessary. I know how to organize photos in Adobe Bridge. What I'm clear on is how to create captions for the photos that will will be permanently linked to the photo files and can be output for on-screen or print albums / galleries.
Also, what is a good tool for creating output? InDesign is an obvious possibility for print; but I was wondering if there is some sort of plug-in or companion product for PS designed specifically for generating albums and slideshows.
Photoshop Elements :: Digitizing And Cataloging Mini DV Tapes
Dec 23, 2012I recently got rid of my Canon GL1. before I did, I captured 30+ hours of footage using Premier Elements. Unfortunately, I cant view it without using premiere. All I want to do is save it as useable date for future editing in a format that is versatile as well as be able to catalog it easily.
View 1 Replies View RelatedAutoCad 3D :: Multiple Visual Styles For Buildings
Aug 5, 2012I want to create 2 visual styles for buildings in autocad 2011, I have the main building then a proposed extension to it! I want to show the original building in say x ray visual style n extension in realistic?
I could do something in paperspace using polygonal viewports, but unsure how to do this?
AutoCAD 2010 :: Buildings At Different Angles - Rotate Views
Jun 4, 2012I have a site plan that has buildings at different angles. How do I rotate my view so that the buildings are displayed at a normal x,y view?
View 1 Replies View RelatedAutoCAD Civil 3D :: Multiple Surface Masks For Buildings
Feb 25, 2011I'm now using a different computer. I have a drawing with an existing surface and contours. I have two buildings on site that I'd like to mask the contours that run through them. I used the mask feature for one of them, but that is the limit. How can I mask the contours so they aren't running through the other building.
View 8 Replies View RelatedAutoCad 2D :: Multiple Buildings Surrounded By Water Wells - Scaling
May 21, 2012I'm working on a drawing of a jobsite. The jobsite has multiple buildings surrounded by water wells. Each well has a unique ID, ie MW-7. In model space everything is drawn at a 1:1 scale. The jobsite is quite large, and in layout view my scale is set to 1"=100'. Everything looks visually pleasing, text size, block sizes (symbol for the well location, etc.). However, I need to create a new layout that zooms into a particular portion of the site. I need my scale to be roughly 1"=50'.
My question is this: How can I set my drawing so that when I zoom into the area of interest, the block symbols and the well IDs stay the same size and don't crowd up the entire page? Otherwise my well IDs are huge! I think it might have something to do with annotative scaling, but I can't get it to work properly. This drawing is being done in AutoCAD 2012
AutoCAD 2010 :: How To Create Complex 3D Solid For Buildings Ceiling
Jun 4, 2013I have a problem when designing one building in 3d. The thing is i want to create a 3d model made only out of 3d solids. So there is this complex ceiling, I made out of 3 meshes and above it, in the above floor, there's a non complex plate.
[URL] ........
This meshes are made based on the actual dimensions of different sides of the floor, are unique and are good approximation of the actual building's ceiling. So, I want to make 3d solid that would have the same bottom shape and the same - even top as in the picture if the space between the objects would be filled out.
AutoCAD 2013 :: Simple Floor Plans For Commercial And Residential Buildings?
Feb 18, 2013I need to be able to do simple floor plans for commercial and residential buildings, what version of autocad do I need?
Will autocad 2013 LT be good enough?
AutoCAD Civil 3D :: Add Hide Boundaries To Existing Houses / Buildings Footprints
May 17, 2012I have a rather large surface and am trying to add hide boundaries to the existing houses/Buildings footprints however whenever I do my whole surface disappears.
View 4 Replies View RelatedAutoCad 2D :: Clear List Of Main Layers Lines Weights And Colors For Residential Buildings?
Oct 29, 2013i want clear list of main layers lines weights and colors for residential buildings? (we use stone out wall and normal blocks inside)
I try BS 1192 and ISO but they are misappointed me.
for ex they use
1-ext wall white .5
2- hatch blue .18 !! (not clear color and not light weight)
3- int. wall color: 9 weight: .25
AutoCAD LT :: Extreme Lag While Drawing PLine
Nov 18, 2013I have terrible lag whenever I am drawing a polyline. It seems like it is taking forever to render the preview of the line when I am dragging the line across the screen. I would prefer to just turn off the line preview if at all possible. So far, I have not been able to find a way to do this. When I say preview of the line, I am talking about the transparent line that follows your cursor after you start a polyline and exists until you click to place the line where you want it.
I am running Windows 7 Pro 64-bit
Dell Precision M6600
8-gb ram
NVIDIA® Quadro® FX 2800M graphics
AutoCAD Civil 3D :: Ellipse To Pline
Aug 8, 2012Recieved a ACAD converted Microstation File for use in an upcoming construction project. Would like to convert all of the existing ellipses to polylines. Have read several threads that lead me to believe redrawing them is about the only real way to do it. Posting here in hopes of a solution. Drawing contains 127 ellipses, and I dont want to redraw all of them!!
Currently on C3D2012.
AutoCad :: Convert 3DSPline Into A Pline?
Jan 12, 2012what I need to do is to flatten a spline into a pline because I need to measure its diameter.
I know how to it with a 2d spline but how can I manage in case I have a 3d one?
AutoCad 2D :: Converting PLine To Revcloud
Dec 11, 2012I'm using AutoCAD 2013 and it will not convert a p-line to revcloud .
View 9 Replies View RelatedPhotoshop :: How To Start Using Buildings In Art
Apr 15, 2013I am wanting to start using buildings in my art, what is the best way to do this? ... do i use the pen tool and cut the buildings out of an image or could i create the buildings from scratch?
View 9 Replies View RelatedPhotoshop :: Buildings Falling Over
Sep 21, 2002I know how to crop pics to get rid of unwanted image, but how do you straighten up buildings which are 'leaning' over? I've got some pics of tall buildings and want to s-t-r-e-t-c-h the tops of them so that they look vertical cos they look a bit strange at the moment.
View 1 Replies View RelatedPhotoshop :: Buildings...prespective
Dec 3, 2006I took this picture in Vegas and would like to straighten out the buildings. For the life of me, I cannot remember the correct term to search under.
View 9 Replies View RelatedAutoCAD 2013 :: Snap To 45° Instead Of Perpendicular
Nov 8, 2013So you know how we have the snaps endpoint, perpendicular, midpoint etc. I want to find something like the snap "perpendicular."
Any way to start a line/pline then have it snap to another line at a 45° angle instead of perpendicular?
The only thing I could find was here
[URL]........
but I am not sure what all they are trying to do.
AutoCAD Map 3D :: PNG Perpendicular Lines Going Over The Images
Oct 11, 2012We have encountered problems when we are trying to plotting charts that have geo referenced png images in them. Some of images will have perpendicular lines going over the images, this will only appear in the plotted versions. The lines won't appear in preview or in the drawing nor in pfd plot.
View 1 Replies View RelatedAutoCad 2D :: How To Draw A Perpendicular Bisector
Nov 8, 2011I'm new to Autocad and have problem drawing a perpendicular bisector . I have an oblique line and want to draw its perpendicular bisector . Is there an easy way to do that?
View 7 Replies View RelatedAutoCAD Civil 3D :: Convert Pline To Alignment?
Oct 30, 2013How to convert pline to Alignment C3D 2014
View 1 Replies View RelatedAutoCAD 2013 :: Draw Arrows By Pline
Oct 20, 2013When I did the confirmation after I drew the arrow, it shrank to be small. Like the pictures attached.
View 9 Replies View Related
