AutoCAD LT 12 and 11
1. How can you input text within a circle or square or triangle? The circle , etc would be just larger then the text within.
2. How about with leader added pointing to location?
3. Can this be done using following Macro:
*^C^Ctext;_mc;;;$M=$(getvar,USERI1);setvar;USERI1;$(+,1,$(getvar,USERI1))
or inputted like underlined text :
%%uTEXT HERE
I have 4 points/corners (with XYZ-coordinates) of a square shape created in the DWG of my AutoCAD Civil 3D 2013 program. I want to create 2 "triangle-shape" parcels (one parcel connects Points #1-#2-#3-#1 and the other parcel connects Points #1-#4-#3-#1. How can I create these 2 "triangle-shape" Parcels from the 4 points/corners of a squre shape?
View 9 Replies View RelatedFor example, I have a 10cmx10cm grid with lines every 1cm. I want to turn this square into a triangle by reducing the length of the top edge to a single point. The final image should show the vertical lines reaching up towards the top centre, while still leaving the horizontal lines 1cm apart.
Using DISTORT will push the vertical lines up towards the top, producing uneven spaces between the lines. How do I avoid this? know it would be easy to recreate the desired triangular grid from scratch, but this is just an example of my problem. I need to apply the solution to graphics which cannot be reproduced again - i.e. bitmaps.
how to input square root in a dimension.
I have tried sqrt(5)
IV 2014 returns "expected [in] but found [ul^0.500]
M6700, Nvidia K3000M, 32GB, 512 SSD
Win 7 Ultimate 64
Inventor 2014
I have a question. I'm using VB.Net 2010 with Autocad2012.
How to make code for promt input user.
Get input points from user and draw circle using VB.Net 2010 with Autocad2012.
there are some points in my dwg that I can't move. I can rotate but not move. I noticed in the point file the ones that I can't move have a grey square in the cell with the point number and the ones I can move have an empty circle. How do I change the square to a circle?
View 7 Replies View RelatedHow I can cut a circle from a square image so that the circle is cut from the exact middle of the square? I use the Elliptical Marquee Tool (M) and drag outwards from the approximate middle of the square (Holding Shift and ALT) but after doing so the transform buttons are greyed out.
So then, how can I position the "circle selection" to the exact center of the square? A few pixels out in any direction will not suffice. I'm using CS6.
I have a square that I want to make into a circle, without distorting it. I want to create a circle using it as a stroke... I"m using CS2, can anyone help
I used the transform and the warp tool and got it into a circle, but there were points where it was pinched and it looked stupid.
I thought maybe there was a way to make a circle and use that "pattern" as a stroke for it, but so far I can't figure it out.
i tried making it a brush and needless to say...
We use that square to put around all of our letterhead and official station documents. I've created a CD-Rom media kit of our stuff and want to put it around the edge of the cd label, but unfortunately for me, cd's are round which is not condusive to the template I have....
Im trying to merge two shapes....a square and a circle. (see attached image)
Ive tried using Boolean options and the Attach command but although it links them it doesnt remove the interior geometry. Im sure this is the easiest question ever posted on this forum but I just cant figure it out.
Im trying to get one single shape that I can extrude.
I have a square selection that I'd like to map into a circle of equal size. I see apply lens and map object...sphere, but neither of these seem to do a proper job.
The algorithm I'm after would basically take the pixels of the square and map them onto their new locations within the circle so that each pixel moves inward toward the center until it reaches its appropriate location along the the line from the origin to its radius.
I'm about to the point to just code it in C++.
I have illustrator CS3 - I am making badges and want to change a picture I already have from a square into a circle. I am taking the notebook with me on site and I am not sure if anything but illustrator can run on it. i.e I know I can do it in photoshop but am worried about the poor little bugger screaming blue murder!
So is this possible in Illustrator? I am open to suggestions for other apps that arent so memory hungry like word; gimp maybe?
I recall the "Paint" program you could make a Circle, and drag the circle till you had a tin can or a barrel.How do we do that in <paint.NET>?
View 5 Replies View RelatedMaking a logo in gimp.... Yes i'm new to photoshopping etc. ANyway i need to make a double circle and a double triangle
Here is a drawing of my logo: [URL]...
I'm just wondering whether there is a way to crop an image in PS in a different shape other than the default square. Like circle crop or pentagon.
View 5 Replies View RelatedWhy would my Layer Masks in Adobe Photoshop CS5 extended Now be a square with a round circle in middle and not rectangular & black or white like they were originally ?
View 6 Replies View RelatedHow to draw a perfect circle and how to make sure it is perfectly centered inside a square in Photoshop elements using the Ellipse option.
View 2 Replies View RelatedSo when I create a triangle by using the star shape tool and only giving it three points. When I have my triangle, I duplicate it and make it smaller. I center them both up on the canvas, but they don't look centered. As you can see in the picture provided, the bottom has more of a width that the others. I've tried using the alignment tool and the smart guides. I do resize the triangle using shift so it doesn't mess up the shape too.
View 10 Replies View RelatedI must have fat fingered something and I now when I click on the Eraser Tool or the Brush Mask Tool instead of getting a circle or square, I get and icon of the tool instead. They still work but they're harder to use without seeing the circle or square depending on what's selected. I've been using Corel for many years and never had this happen and I can't figure out how to switch back.
View 3 Replies View RelatedI'm using AutoCAD 2012LT and have somehow lost the text command input box, that shows what commands I am typing in, at the bottom of the screen.
I am using the program in Classic View rather than Ribbon view. I've been unable to log into the subscription help center due to the organisation I work for not being on subscription.
My need is to create up to 50 points from the same origin in a three dimensional Cartesian coordinate system but I’d also like to have a labels for each point that show up in the feature tree.
Are there Inventor 2013 plugin (i.e., add-on, 3rd party, AP) to convert a list 3D Cartesian coordinate system locations (i.e., points) to Inventor to work points(x, y, z)?
I found that I cannot create 3D points in the assembly. Is this correct? I did find that an Inventor part may be used to create a 3D sketch that creates points in 3D space. In the past few days, I found two ways to create 3D points within a iPRT; the batch way uses an Excel file but it then does not allow me to name the points in the feature tree. The second way is to create them one at a time but that take way too much time.
I saw another thread on this, but it went unanswered, so I am going to ask it with some better information.I installed inventor pro 2012, and it was working fine for a few days, but it now is missing the input boxes for the Precise Input window. URL....
View 5 Replies View RelatedIs it possible to lock a text box to prevent it from moving but still be able to input & edit text?I want to make a drawing template in CorelDraw x6 using text boxes for "non Corel friendly" people to use but need the actual text boxes to stay in the same place all the time!?
View 3 Replies View RelatedI've created an input text inside a symbol called "Asks" in a timeline triger i use:
message = sym.$("texto"); // texto is a textfield
message.html("Write here: ");
inputMessage = $('<textarea />').attr({'type':'textarea','value':'', 'id':'message'});
inputMessage .css ('font-size', 18);
inputMessage .css ('box-shadow', '#0a81fb');
[Code] ......
How to make a dynamic block of a callout stretch as text is inputed?
For Example:
(TEXT)
(THIS IS MORE TEXT)
(THIS IS EVEN MORE TEXT)
I will attach a dwg of the callout.
How I can update my diesel expression to display the area in square feet not square inches. See expression below.
^C^Cattdia;0;_-insert;AREABLK;1;1;0;$M=$(getvar,AREA);attdia;1
I've copied and pasted sections from old drawings into new ones, and it seems to have completely messed up some fundamental aspects of my AutoCad.
After I pasted I received some error message which I didn't understand. I think it said something about a "Language" problem, (Needless to say I clicked the nice big "OK" button without any thought). Now, every time I open CAD there are these square symbols where there should be text
I am running CAD from my company computer, so can't use the add/remove programmes repair trick. How I can reset all/relevant settings within CAD to get things back to normal?
I'm running the 2010 model.
I am UNABLE to follow a tutorial on how to make a repeatable pattern using 'texture transfer' on some fire I want to make into a pattern!!! every time I select the area I want to use and the 'input map' and paste as new image and I tell Resynthesizer to use that image it ALWAYS errors out as "The Input Map Should Be The Same Size As The Input Texture Image" according to the tutorial another person gave me on this forum he said NOTHING about being the same size!!! in fact, his selection was SMALLER than the actual image that he was using Resynthesizer on!!!
View 4 Replies View RelatedNow, with that task simplified, I'm not sure how to change the color of the text created using this tool.
View 1 Replies View RelatedI am trying to circle one of the letters and each will receive a number sequence afterwards for the comm addresses (is what I want to do anyway). This is a gov project so I have to ensure everything is addressed properly.
Circling the prefix would make this look ideal but I don't know if there's a way to do it. I tried looking but couldn't find a way to do it.
The only way I could think to do it is do it manually with attdef and create a defined block with the prefix area already circled.
Using: Xara Photo & Graphic Design 6
AMD Athlon II X2 255 Processor 3.10 GHz
2.00GB (1.75 GB usable) RAM
64-bit OS
I follow the tutorial in the Xara Help, but cannot get the results shown. I draw the circle, compose the text, and set it to the middle Select both circle and text Arrange/Fit Text to Curve....the text appears around the lower, right side of the cirle After all this I am unable to manipulate the text (It's a piece of cake to do this in Publisher 2010, but it has some minor problems in appearance)
My text input has started to overlap. Everything is in one line after the return. How can I stop this?
View 2 Replies View Related