For almost a decade I'm used to AutoCAD standard 3D coordinates display: X to right, Y away and Z straight up. For some reason Inventor is configured differently: X to right, Y straight up and Z toward you.
View 3 RepliesI want to ask if in Autodesk Inventor 2013, can we create a part with a different configuration?
example:I made a cube the size of 10mm x 10mm x 10mm, after which it would be revised measures 15mm x 15mm x 15mm. The second revision to change the size of a 12mm x 12mm x 12mm.
Can all the revision is done in one file?And if I want to revise again be 10mm x 10mm x 10mm, can?
Have I been that provides revision always create a new file and the file number so much that hard to figure out which revision. I am still learning Autodesk Inventor 2013.
I am working on a project in Inventor. Long story short, the file destinations got messed up. I was in the process of getting them all in the same folder so that I could organize them, but now the main project won't open. I'm am not the most Inventor-savvy. how to fix it.
The message that pops up is "Cannot find applets configuration file"
Inventor 2013 on win7 64bit
In our College we use roaming profiles.
If I make changes to configuration while profile is "open" we run into lots of trouble including total dis-functioning of the mold design and OS does not recognize the inventor file extensions and more problems.
A work around solution we found is to completely un install the program from one computer while the profile is "open" so there will be no association between the profile and the local installations on all computers.
However, now I can not save the configuration changes in any of the class computers. ( our OS disk is protected against permanent changes and will reset itself on any restart reboot, unless an administrator does them).
I tried making changes to the configuration both as administrator user and also when giving the local user administrator privileges, but with no successes.
After rebooting, we lose all configurations.
A client was looking to develop a custom interface for documenting iAssemblies.
Would it be possible with iLogic to:
1. Show form.
2. User selects a Browse button to select iAssembly to document.
3. List all iAssembly configurations in the form.
4. User picks configuration.
5. Select OK to create base view, projected view, and Parts List.
This may require API.
How to use different configuration of parts made with iLogoc in assembly? I want to have equal part with different configuration. I have a problem with the equal files.How to use different configuration of an assembly made with iLogic in assembly?
View 4 Replies View RelatedI have an assembly that is identical to another assembly with the exception of 2 or 3 components. I want to create 2 different configurations of the assembly, e.g. 12345-009 for the original assy and 12345-019 for the similar assy that has a couple of different components and/or additional components. I can create the -009 assembly and then do a "Save As" for the -019 assy and do a "Component/Replace" and add (or delete) other components.
I want both of these assemblies to be on the same drawing with a base number of 12345. I know I can do this and create a separate parts list (BOM) for each configuration and put it on the drawing. Is there a way to "merge" the two PLs so that there is a quantity column for each configuration (-009 and -019)? For example, if the same gear is used in both assemblies, I want a quantity of 1 in each column. If a component is used in one but not the other, i want only the quantity to show up in the appropriate configuration column.
I am using Inventor 2011.
I'm creating a drawing for an iassembly, and I can't get the parts list to automatically show a specific configuration's BOM. I've tried filtering, "Ballooned Items Only," and that doesn't change anything. I've tried to create a parts list that looks at the child assembly, and the parts list reverts to the parent iassembly.
In the Browser, there's a lightening bolt next to each parts list in the tree. There are three parts lists/configurations.
The parts list lists parts that aren't in the assembly shown, and/or shows wrong quantities. I can manually update the bom, but I would much rather not. Is there a macro or add in that may be useful? I'll be making many prints from iassemblies, and this would be very useful.
Where is the configuration for the Default Template Measurement units stored? Have tried creating an application options file, but on the clients this setting is not read/stored (still set to inches after import).
Is this setting stored in the registry? Where?
...and why does Inventor default to a non metric measurement unit?
Here in my office we have several pc's running Inventor 2012 and we found out that when a network license is unavailable (the number of licenses is exceeded) then Inventor loses some of its configurations on OPTION window. The fields that are erased and put back to default:
- "General" Tab >> "Load VBA on start-up" is set to false;
- "General" Tab >> "Update physical properties on save" is set to false and "Parts and Assemblies" is unchecked;
- "File" Tab >> "Default VBA project" is set back to default;
- "Contet Center" Tab >> "Location of Libraries" is set to default
- Customized buttons on Ribbonbar loses its icons and we have to recreate them everytime it happens.
have a fix and a new implementation for the new versions to come?
I want to create one Spur Gear in inventor with equations such that i can build more gears from this base model using excel table. For. Eg. I would like to create a gear with 40 No. of teeth of 10DP, and 20°PA, with Pitch Circle Dia, Base CIrcle Dia, Tooth Thickness based on spur gear calculations.
Now i would like to create a series of such spur gears with varying no. of teeth, i.e. 42, 44, 46, 48, 50..etc. Now if i change the No of teeth ,Accordingly the gear should modify its pitch dia, Base circle dia, Tooth Thickness which would be noted in the Equation.
how to create thes equations and use these in creating gear with different no. of teeth.
I have shown below list of gear data for various no. of gear.
i am trying to translate a Point coordinates from Paperspce to world coordinates in model space.The code i used in Land2006 worked OK but now in Civil3d 2012 it doesn't!
Private Sub GetPlais_Click()
Dim tmpnt1 As Variant, tmpnt2 As Variant, tmpPnt1 As Variant
Dim lole(0 To 2) As Double, upri(0 To 2) As Double
Dim returnobj As AcadObject
FrmGrid3.Hide
On Error GoTo Eline
ThisDrawing.Utility.GetEntity returnobj, tmpPnt1, "ÅðÝëåîå ôï ViewPort ðïõ èá äçìéïõñãçèåß ï êÜíáâïò!"
If TypeOf returnobj Is IAcadPViewport Then
[code]........
I'm a GIS analyst trying to learn Cad. I'd like to place a single point in autocad model space at a specific Northing/Easting position. After reading several forum threads I don't think CAD allows me to change the coordinate system of model space from map coords to northing easting coords, as we can in GIS.
View 5 Replies View RelatedI need to get the dimensions of a lot of centers from parts in a drawing for inspection with a laser tracker.
Is there a way of setting a point from an reference and get a table of the values from the centers I select (x, y and z).
I need to get all the coordinates from the blue and white parts (inside and outside)...
I have a 3D part that produced from an assembly document. (pic.1). How can I take the coordinates of the curve that is designed on the right surface (pic.2) in a .txt or better .xls file ?
That curve I want to draw it in Excel.
How to get coordinates of a workpoint using iLogic.
Config :: Intel (R) Xeon (R) CPU E31245 @ 3.30 GHz, 16.0 GB, 64bit win7
Inventor 2013 and Vault Basic 2013
In Inventor, I want to look for a table called "MS6 Report". If the table exists, I want to get its coordinates, and delete the table. If it doesn't exist, I'd just like to let the user place a table. How can I check if a customtable by this name already exists in the document? Here is what I have so far...
if (aDoc.ActiveSheet.CustomTables.Equals("MS6 Report")){//get table coordinates//delete table }else {userInteract = m_inventorApplication. Command Manager.CreateInteractionEvents();keySelect = userInteract.KeyboardEvents;keySelect.OnKeyDown += new Keyboard EventsSink_ OnKey Down EventHandler(keySelect_OnKeyDown);mouseSelect = userInteract.MouseEvents;mouseSelect.OnMouseDown += new MouseEventsSink_ OnMouse DownEventHandler(Table_Update_Placement); }
The else statement works great. No problems there. How can I find, get coordinates of, and delete a custom table by the name of "MS6 Report"?
How can I change the coordinates directions? You know X to -X or Y to -Y.
View 4 Replies View Related Im doing some pictures for a broschure.
There are several products to render out and I like each product to be viewed in same position.
When i rotated the product in a view i like can I save the position coordinates and set them later in another product?
get the same view position all the time?
Is it possible to pull out the x,y,z coordinates to text file from a inventor part. I am aware about this that it maybe need some programming but what kind of programming Language is the best to use ? is it possible to use the build in programming Language called Ilogic? Or is it better to use some .net? At my work we use PDMS to do plant modelling and we want to use inventor for modelling the machines and doing the workshop drawings ect. And we want to be able to take the inventor part coordinates and transfer them to PDMS because it can model the machines just by coordinates taken from a text fil.
View 1 Replies View RelatedI try to develop a vba code to get the coordonates of each part of an assembly and after export them to an excel file.
I build this :
Public Sub Export_Layout_COG()
If MsgBox("Cette Macro va exporter les coordonnées du COG de chaque layout, continuer ?", vbYesNo) = vbYes Then
Dim RefDoc As Document
Set RefDoc = ThisApplication.ActiveDocument
Refdocdisplayname = RefDoc.DisplayName
[Code]...
The code return an error on the red line, I don't catch why?
The coordinates that we can apply in Revit (project/shared) aren't exactly the same to have real world projection coordinates (WGS84)??
If not how can we convert the revit shared coordinates to real world projection coordinates?
Why is it, when I go to Flat Pattern/export to DXF that everything ends up upside down.I have part where it is important that the correct side is faced upp, (brusched steel).
When i Export it to dxf, it is upside down, and the bruched facefacing down.
I'm trying to build a VBA code in inventor 2010 to export the Center of gravity coordinates (X,Y,Z) from an inventor assembly to an excel sheet.
But I'm not able to get the iproperties for the COG from my assembly.
So we have a new plotter at work, and I am trying to use it with the publish command. However, because all of our old drawings are saved with our old plotter name, choosing the new plotter isn't an option for all of our old dwgs that havent been set up using the new plotter name. Since our dwgs number in the 1000s, going through each one and renaming them would be impracticable.. but having to individually plot each one is pretty impracticable as well..
So I tried to figure out a workaround, by opening up our new template that has the new plotter configuration on it, hoping I would be able to use it to set all the old dwgs that I have open at the time to the new plot setting.. but the printer name comes up as something different when I try to use it for publish, and if I use it, I get an error and nothing prints. I know the settings used in the new template work, I have been able to print it out. So what I'm asking is, is there anyway I can use the new plotter to publish all of our old drawings?
i tried to print a drawing and it said configuration cannot be used for thefollowing reasons: either driver not found or driver has problem or device cannot be found. however i can print everything else except when i am using autocad?
View 9 Replies View RelatedI'm using ACA 2011
How do I configure dwg to pdf output to version 5, many customers do not have Reader 7 and have no intention of downloading the newer reader. I see no area in the Plot Configuration Editor??
What’s up with that
Since we've migrated to Windows 8 64b we have problems wih plotting some layouts. If I select my plotter it automatically goes to none after selecting and sometimes I get the following error message:
Most of the times I can use the plotter in the other layouts / drawings, but sometimes I have to restart AutoCAD or reboot the computer before the plotter works again. In some layouts we keep getting this problem even after reboot. I've tried reinstalling the plotter (with different drivers), tried different computers, purge and recover the drawings but no luck. The Plotter is a HP Designjet 800.
I need to set the Printer Configuration Search Path and the Plot Style Table Search Path. Currently I am using COM but the issue I have is that I need to run the same application on 2 different machines, one has only Autocad 2010 (xp-32bit), the other has both Autocad 2010 and Autocad 2012(win7-64bit) and I've got some difficulty to have it running.
Can I set those paths without using COM?
How to set or change the active display configuration with .NET. Currently I am sending this task to the command line. See below:
' This subroutine sets the correct display config with the supplied name Public Sub SetCurrentDisplayConfig(ByVal strDisplayConfig As String)Dim strCommand As String = "" strCommand = "-AECDISPLAYCONFIGSETCURRENT " & strDisplayConfig & vbCr AutoApp. Application. DocumentManager. MdiActiveDocument.SendStringToExecute(strCommand, True, False, False) End Sub
Whenever I attempt to print, I get the warning message below referring to a printer that I do not have. I presume it's an AutoCAD default setting, but I cannot find any place allowing me to change this default. It eventually prints, since as the warning message says, it then substitutes my Mac's default printer, Is there any way to change the AutoCAD setting.
View 2 Replies View Related